Hello there I have installed NetBSD 3.0 sparc on a SparcStation 20 and 
have updated to stable, built and installed a kernel. However I have the 
following problem even with the GENERIC kernel, there is no consol cursor 
so it's very difficult to edit files at the console. The graphics 
card is a TGX, has any one come across this problem? I have also done a 
CVS update of the source but have yet to build and install user land.
Would this help?

Any help appreciated, regards John.

Dmesg follows:-

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005
     The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
     The Regents of the University of California.  All rights reserved.

NetBSD 3.0_STABLE (ARTHUR1) #0: Sat Mar 11 17:15:04 GMT 2006
         johng@arthur.powinv.co.uk:/usr/src/sys/arch/sparc/compile/ARTHUR1
total memory = 127 MB
avail memory = 120 MB
bootpath: 
/iommu@f,e0000000/sbus@f,e0001000/espdma@f,400000/esp@f,800000/sd@3,0
mainbus0 (root): SUNW,SPARCstation-20I: hostid 723c01ea
cpu0 at mainbus0: TMS390Z50 v0 or TMS390Z55 @ 60 MHz, on-chip FPU
cpu0: physical 20K instruction (64 b/l), 16K data (32 b/l), 1024K external 
(32 b/l): cache enabled
obio0 at mainbus0
clock0 at obio0 slot 0 offset 0x200000: mk48t08
timer0 at obio0 slot 0 offset 0x300000: delay constant 28
zs0 at obio0 slot 0 offset 0x100000 level 12 softpri 6
zstty0 at zs0 channel 0
zstty1 at zs0 channel 1
zs1 at obio0 slot 0 offset 0x0 level 12 softpri 6
kbd0 at zs1 channel 0: baud rate 1200 (console input)
ms0 at zs1 channel 1: baud rate 1200
fdc0 at obio0 slot 0 offset 0x700000 level 11 softpri 4: chip 82077
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
auxreg0 at obio0 slot 0 offset 0x800000
power0 at obio0 slot 0 offset 0xa01000 level 2
iommu0 at mainbus0 ioaddr 0xe0000000: version 0x3/0x0, page-size 4096, 
range 64MB
sbus0 at iommu0: clock = 20 MHz
dma0 at sbus0 slot 15 offset 0x400000: DMA rev 2
esp0 at dma0 slot 15 offset 0x800000 level 4: ESP200, 40MHz, SCSI ID 7
scsibus0 at esp0: 8 targets, 8 luns per target
ledma0 at sbus0 slot 15 offset 0x400010: DMA rev 2
le0 at ledma0 slot 15 offset 0xc00000 level 6: address 00:40:dc:01:01:ea
le0: 8 receive buffers, 2 transmit buffers
bpp0 at sbus0 slot 15 offset 0x4800000 level 2 (ipl 3): DMA rev 2
SUNW,DBRIe at sbus0 slot 15 offset 0x8010000 level 9 not configured
cgsix0 at sbus0 slot 2 offset 0x0 level 9: TGX120,170-0006, 1152 x 900, 
rev 11 (console)cgsix0: attached to /dev/fb

eccmemctl0 at mainbus0 ioaddr 0x0: version 0x0/0x2
Kernelized RAIDframe activated
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 3 lun 0: <WDIGTL, ENTERPRISE, 1.91> disk fixed
sd0: 4157 MB, 5720 cyl, 8 head, 186 sec, 512 bytes/sect x 8515173 sectors
sd0: sync (100.00ns offset 15), 8-bit (10.000MB/s) transfers, tagged 
queueing
root on sd0a dumps on sd0b
root file system type: ffs