On Sun, Apr 10, 2005 at 03:38:49PM -0400, Michael wrote:
> Hello,
>
>>> tadpole# mount -t msdos /dev/wd0c /mnt
>>> mount_msdos: /dev/wd0c on /mnt: Operation not supported by device
>>
>> This can be because the kernel doesn't have support for MSDOS filesystem
>

> True. Why didn't I think of that? 

> Anyway, a dd of the first couple of sectors from the CF card should
> show something recognizable, all I want to know is if data transfers
> actually work.

Why do things small? =)

I did a 'dd if=/dev/wd0c of=cf.img bs=512 count=1024

It got 323584 bytes into it and through an error, which it claimed it
corrected, but it quit writing to the file.

> Mike - I'll make a kernel with MSDOSFS support ASAP.

Attached is the dmesg with said errors, plus the entries from when I
plugged in this Prism 2.5 WLAN card.

-- 
Michael Parson
mparson@bl.org

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 3.99.3 (MORGOTH) #203: Fri Apr  8 10:35:12 EDT 2005
	root@morgoth:/data/src/sys/arch/sparc/compile/MORGOTH
total memory = 65204 KB
avail memory = 61096 KB
bootpath: /iommu@0,10000000/sbus@0,10001000/ledma@4,8400010/le@4,8c00000
mainbus0 (root): Tadpole_S3GX: hostid 80ae2037
cpu0 at mainbus0: MB86904 @ 110 MHz, on-chip FPU
cpu0: 16K instruction (32 b/l), 8K data (16 b/l): cache enabled
obio0 at mainbus0
clock0 at obio0 slot 0 offset 0x202000: mk48t08
timer0 at obio0 slot 0 offset 0xd00000: delay constant 52
zs0 at obio0 slot 0 offset 0x100000 level 12 powered via auxio2 softpri 6
zstty0 at zs0 channel 0
zstty1 at zs0 channel 1
zs1 at obio0 slot 0 offset 0x0 level 12 softpri 6
kbd0 at zs1 channel 0: baud rate 1200 (console input)
wskbd0 at kbd0: console keyboard
ms0 at zs1 channel 1: baud rate 1200
wssunkbd_enable
open...
kbd_sun_open
init...
slavioconfig at obio0 slot 0 offset 0x800000 not configured
auxreg0 at obio0 slot 0 offset 0x900000
auxiotwo0 at obio0 slot 0 offset 0x910000
tctrl0 at obio0 slot 0 offset 0xd1000020 level 11
tctrl0: main power available
clk-ctrl at obio0 slot 0 offset 0x3c0000 not configured
com0 at obio0 slot 0 offset 0x3a0000 level 13: ns16550a, working fifo
iommu0 at mainbus0 addr 0x10000000: version 0x4/0x0, page-size 4096, range 64MB
sbus0 at iommu0: clock = 22 MHz
pnozz0 at sbus0 slot 0 offset 0x8000000 level 2: rev 4, 800x600, depth 8 (console)
wsdisplay0 at pnozz0 kbdmux 1: console (default, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
pnozz0: attached to /dev/fb
dma0 at sbus0 slot 4 offset 0x8400000: DMA rev 2
esp0 at dma0 slot 4 offset 0x8800000 level 4: ESP200, 40MHz, SCSI ID 7
scsibus0 at esp0: 8 targets, 8 luns per target
SUNW,bpp at sbus0 slot 4 offset 0xc800000 level 3 not configured
ledma0 at sbus0 slot 4 offset 0x8400010: DMA rev 2
le0 at ledma0 slot 4 offset 0x8c00000 level 6: address 00:00:83:ae:20:37
le0: 8 receive buffers, 2 transmit buffers
tslot0 at sbus0 slot 1 offset 0x2000000 level 11: 2 slots
pcmcia0 at tslot0 socket 0
pcmcia1 at tslot0 socket 1
wdc0 at pcmcia1 function 0: <HITACHI, FLASH, 5.0>
wdc0: i/o mapped mode
atabus0 at wdc0 channel 0
dbri0 at sbus0 slot 2 offset 0x40 level 9dbri0: need to power up first....done
: rev s3
configuring interrupts...
mmcodec_init: PIO reads c
dbri0: onboard CS4215 detected
pipe setup: 4
pipe setup: 20
pipe setup: 6
pipe setup: 21
pipe setup: 17
pipe setup: 18
pipe setup: 19
dbri0: cs4215 found at offset 0
audio0 at dbri0: half duplex
scsibus0: waiting 2 seconds for devices to settle...
wd0 at atabus0 drive 0: <Hitachi XX.V.3.3.0.0>
wd0: drive supports 1-sector PIO transfers, LBA addressing
wd0: 122 MB, 978 cyl, 8 head, 32 sec, 512 bytes/sect x 250368 sectors
wd0: drive supports PIO mode 4
sd0 at scsibus0 target 3 lun 0: <IC25N020, ATCS04-0, 1.06> disk fixed
sd0: 19077 MB, 38760 cyl, 16 head, 63 sec, 512 bytes/sect x 39070080 sectors
sd0: sync (100.00ns offset 15), 8-bit (10.000MB/s) transfers
root on le0
nfs_boot: trying DHCP/BOOTP
nfs_boot: timeout...
nfs_boot: timeout...
nfs_boot: timeout...
nfs_boot: trying RARP (and RPC/bootparam)
nfs_boot: client_addr=192.168.15.4 (RARP from 192.168.15.2)
nfs_boot: server_addr=192.168.15.2
nfs_boot: hostname=tadpole
nfs_boot: timeout...
nfs_boot: timeout...
nfs_boot: timeout...
root on 192.168.15.2:/home/netboot
root file system type: nfs
wd0: no disk label
wd0: no disk label
wd0 detached
atabus0 detached
wdc0 detached
wdc0 at pcmcia1 function 0: <HITACHI, FLASH, 5.0>
wdc0: i/o mapped mode
atabus0 at wdc0 channel 0
wd0 at atabus0 drive 0: <Hitachi XX.V.3.3.0.0>
wd0: drive supports 1-sector PIO transfers, LBA addressing
wd0: 122 MB, 978 cyl, 8 head, 32 sec, 512 bytes/sect x 250368 sectors
wd0: drive supports PIO mode 4
wd0: no disk label
wdc0:0:0: lost interrupt
	type: ata tc_bcount: 2048 tc_skip: 0
wd0c: device timeout reading fsbn 408 of 408-411 (wd0 bn 408; cn 1 tn 4 sn 24), retrying
wd0: soft error (corrected)
wi0 at pcmcia0 function 0: <11Mbps, Wireless LAN PC Card, Version 01.02, >
wi0:wi0: record read mismatch, rid=fc01, got=1fc
 802.11 address 00:02:72:f0:03:94
wi0: record read mismatch, rid=fd0b, got=bfd
wi0: using Unknown Lucent chipwi0: record read mismatch, rid=fd20, got=20fd

wi0: Lucent Firmware: Station (0.0.0)
wi0: record read mismatch, rid=fd10, got=10fd
wi0: using default channel list
wi0: record read mismatch, rid=fc03, got=3fc
wi0: record read mismatch, rid=fd4f, got=4ffd
wi0: record read mismatch, rid=fdc6, got=c6fd
wi0: no supported rate list
wi0: failed to attach controller
wi0 detached
wi0 at pcmcia0 function 0: <11Mbps, Wireless LAN PC Card, Version 01.02, >
wi0:wi0: record read mismatch, rid=fc01, got=1fc
 802.11 address 00:02:72:f0:03:94
wi0: record read mismatch, rid=fd0b, got=bfd
wi0: using Unknown Lucent chipwi0: record read mismatch, rid=fd20, got=20fd

wi0: Lucent Firmware: Station (0.0.0)
wi0: record read mismatch, rid=fd10, got=10fd
wi0: using default channel list
wi0: record read mismatch, rid=fc03, got=3fc
wi0: record read mismatch, rid=fd4f, got=4ffd
wi0: record read mismatch, rid=fdc6, got=c6fd
wi0: no supported rate list
wi0: failed to attach controller