I'm trying to install netbsd 1.5.2 and I just got it booting from the cd and it crashes.  Any ideas on how to fix this?  The Drive it took out of an old network appliance filer, and put into the system.  It's worked before with solaris 2.5.1, but it seems to panic after tickling all the scsi devices.


Bad memory address line test Memory address not alignedType b (boot), c (continue), or n (new command mode)
>n
Type  help  for more information
ok probe-scsi
Target 2 
  Unit 0   Disk     SEAGATE ST12400N        865000949801Copyright (c) 1994 Seagate All rights reserved 0000
Target 6 
  Unit 0   Removable Read Only device     SONY    CD-ROM CDU-8012 3.1e
ok boot sd(0,6,1)
Probing Memory Bank #: 1 2 3 4 5 
Booting from: sd(0,6,1) 
>> NetBSD/sparc Secondary Boot, Revision 1.9
>> (toor@proxima, Tue Aug 21 23:18:13 CST 2001)
Booting netbsd
1311410+773468+152836=0x2326d0
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.5.2 (INSTALL) #0: Wed Aug 22 05:51:09 CST 2001
    toor@proxima:/usr/src/sys/arch/sparc/compile/INSTALL
total memory = 65484 KB
avail memory = 61196 KB
using 128 buffers containing 512 KB of memory
bootpath: /sbus0/esp0/sd@6,0:b
mainbus0 (root): Sun 4/65
cpu0 at mainbus0: MB86900/1A or L64801 @ 25 MHz, WTL3170/2 FPU
cpu0: 64K byte write-through, 16 bytes/line, sw flush: cache enabled
memreg0 at mainbus0 ioaddr 0xf4000000
clock0 at mainbus0 ioaddr 0xf2000000: mk48t02 (eeprom)
timer0 at mainbus0 ioaddr 0xf3000000 ipl 10 delay constant 10
auxreg0 at mainbus0 ioaddr 0xf7400000
zs0 at mainbus0 ioaddr 0xf1000000 ipl 12 softpri 6
zstty0 at zs0 channel 0 (console i/o)
zstty1 at zs0 channel 1
zs1 at mainbus0 ioaddr 0xf0000000 ipl 12 softpri 6
kbd0 at zs1 channel 0
ms0 at zs1 channel 1
fdc0 at mainbus0 ioaddr 0xf7200000 ipl 11 softpri 4: chip 82072
audio at mainbus0 ioaddr 0xf7201000 ipl 13 not configured
sbus0 at mainbus0 ioaddr 0xf8000000: clock = 25 MHz
dma0 at sbus0 slot 0 offset 0x400000: rev 1
esp0 at sbus0 slot 0 offset 0x800000 level 3: ESP100, 25MHz, SCSI ID 7
scsibus0 at esp0: 8 targets, 8 luns per target
le0 at sbus0 slot 0 offset 0xc00000 level 5: address ff:ff:ff:ff:ff:ff
le0: 8 receive buffers, 2 transmit buffers
cgsix0 at sbus0 slot 2 offset 0x0 level 7: SUNW,501-1481, 1152 x 900, rev 2
cgsix0: attached to /dev/fb
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 2 lun 0: <SEAGATE, ST12400N, 8650> SCSI2 0/direct fixed
sd0: 2048 MB, 2621 cyl, 19 head, 84 sec, 512 bytes/sect x 4194685 sectors
cd0 at scsibus0 target 6 lun 0: <SONY, CD-ROM CDU-8012, 3.1e> SCSI2 5/cdrom removable
md0: fixed, 1360 blocksdata fault: pc=0xf0045bbc addr=0xf1a5e1ac ser=8080<WRITE,INVAL>
panic: kernel fault
syncing disks... done
Frame pointer is at 0xf015be18
Call traceback:
  pc = 0xf0114680  args = (0x10e0, 0x1fe0, 0x0, 0xf0166800, 0xf015bf30, 0x9010e0, 0xf015be80) fp = 0xf015be80
  pc = 0xf0046c7c  args = (0x100, 0x0, 0xf0228000, 0x0, 0xf015bfa4, 0x9010e1, 0xf015bee8) fp = 0xf015bee8
  pc = 0xf0121e58  args = (0xf0143f18, 0x100, 0xf1a5e1ac, 0xf015bfb0, 0x2f, 0x2, 0xf015bf50) fp = 0xf015bf50
  pc = 0xf000857c  args = (0x9, 0x8080, 0xf1a5e1ac, 0xf0045bbc, 0x40, 0xf015c058, 0xf015bff8) fp = 0xf015bff8
  pc = 0xf0045b80  args = (0xf039e0f8, 0xf1a5e1a8, 0x1, 0xf004653c, 0xf039e0f0, 0x1a7c000, 0xf015c0a8) fp = 0xf015c0a8
rebooting


Thanks in advance!!
Blake