I am trying to use a sun 501-2015 scsi/enet sbus card in a Sparc IPC under
NetBSD 1.4.1, but the kernel panic crashes when trying to configure the
scsi device (while booting off of the mother-board scsi):

Booting from: sd(0,2,0)netbsd
>> NetBSD/sparc Secondary Boot, Revision 1.8
>> (mrg@sun4690, Mon Jul 19 04:22:51 PDT 1999)
Booting netbsd @ 0x4000
1638400+123640+152516+[90888+107539]=0x207ddf
console is ttya
Copyright (c) 1996, 1997, 1998, 1999
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.4.1 (DEI) #0: Fri Feb 11 13:41:57 CST 2000
    sbnoble@dei:/usr/src/sys/arch/sparc/compile/DEI
real mem = 37695488
avail mem = 34295808
using 128 buffers containing 524288 bytes of memory
bootpath: /sbus0/esp0/sd@2,0
mainbus0 (root): Sun 4/40
cpu0 at mainbus0: MB86900/1A or L64801 @ 25 MHz, WTL3170/2 FPU
cpu0: 64K byte write-through, 16 bytes/line, sw flush: cache enabled
memreg0 at mainbus0 ioaddr 0xf4000000
clock0 at mainbus0 ioaddr 0xf2000000: mk48t02 (eeprom)
timer0 at mainbus0 ioaddr 0xf3000000 ipl 10 delay constant 10
auxreg0 at mainbus0 ioaddr 0xf7400000
zs0 at mainbus0 ioaddr 0xf1000000 ipl 12 softpri 6
zstty0 at zs0 channel 0 (console)
zstty1 at zs0 channel 1
zs1 at mainbus0 ioaddr 0xf0000000 ipl 12 softpri 6
kbd0 at zs1 channel 0
ms0 at zs1 channel 1
fdc0 at mainbus0 ioaddr 0xf7200000 ipl 11 softpri 4: chip 82072
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
audioamd0 at mainbus0 ioaddr 0xf7201000 ipl 13 softpri 4
audio0 at audioamd0: full duplex
sbus0 at mainbus0 ioaddr 0xf8000000: clock = 25 MHz
dma0 at sbus0 slot 0 offset 0x400000: rev 1
esp0 at sbus0 slot 0 offset 0x800000 level 3: ESP100A, 25MHz, SCSI ID 7
scsibus0 at esp0: 8 targets, 8 luns per target
probe(esp0:2:0): max sync rate 5.00Mb/s
sd0 at scsibus0 targ 2 lun 0: <SEAGATE, ST410800N, 0025> SCSI2 0/direct fixed
sd0: 8669MB, 4926 cyl, 27 head, 133 sec, 512 bytes/sect x 17755614 sectors
le0 at sbus0 slot 0 offset 0xc00000 level 5: address 08:00:20:0d:c8:e7
le0: 8 receive buffers, 2 transmit buffers
dma1 at sbus0 slot 1 offset 0x81000: rev esc
esp1 at sbus0 slot 1 offset 0x80000 level 3async mem arr: ser=18<SBUSERR,MEMERR>
 sva=0x0 aer=80<WBINVAL> ava=0xfe02402c
parity error register = 0
panic: memory error
halted

Program terminated


Does anyone know if this is a known issue, configuration problem, or
hardware problem?  I've tried both slots 1 and 2 and the crash occurs
regardless of whether devices are connected to the card.

Thanks!

-- 
Seth Noble - President - Data Expedition, Inc. - http://DataExpedition.com/  O-