Subject: Re: SPARCstation ss5 panic at boot time.
To: Grey Wolf <greywolf@siteROCK.com>
From: Jonathan O'Brien <obrien@hulk.sfsu.edu>
List: port-sparc
Date: 03/30/2000 12:59:18
I think it's the snapshot. I tried to install it on my SS10 and
failed with the same problem. Things work great from kernels built
from source ~3/17.

jonathan

On Thu, 30 Mar 2000, Grey Wolf wrote:

> I just inherited a new SS5 and would obviously prefer it ran BSD.
> 
> I have it set up booting diskless with the netbsd.GENERIC.gz kernel
> found in ftp.netbsd.org:/pub/arch/sparc/snapshot/20000304/binary/
> kernel/.
> 
> This is a visual transliteration so this is about as far as I can read:
> 
> zs1 at obio slot0 offset0x0 level 12 softpri 6
> zs_console flags: 1
> kbd0 at zs1 channel 0 (console input)
> zs_console flags: 0
> ms0 at zs1 channel 1
> slavioconfig at obio0 slot 0 offset 0x800000 not configured
> auxreg0 at obio0 slot 0 offset 0x900000
> power0 at obio slot 0 offset 0x910000 level 2
> fdc0 at obio0 slot 0 offset 0x400000 level 11 softpri 4: chip 82077
> fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
> iommu0 at mainbus0 addr 0x10000000: version 0x5/0x0, page-size 4096, range 64MB
> sbus0 at iommu0: clock = 21.250 MHz
> dma0 at sbus0 slot 5 offset 0x8400000: rev 2
> esp0 at dma0 slot 5 offset 0x8800000 level 4: ESP200, 40MHz, SCSI ID 7
> scsibus0 at esp0: 8 targets, 8 luns per target
> bpp0 at sbus0 slot 5 offset 0xc800000 level 2 (ipl 3): rev 2
> ledma0 at sbus0 slot 5 offset 0x8400020: rev 2
> le0 at ledma0 slot 5 offset 0x8c00000 level 6: address 08:00:20:8e:65:05
> le0: 8 receive buffers, 2 transmit buffers
> le0: supplying EUI64: 08:00:20:ff:fe:8e:65:05
> audiocs0 at sbus0 slot 4 offset 0xc000000 level 9: CS4231A
> audio0 at audiocs0: full duplex
> power-manageent at sbus0 slot 4 offset 0xa000000 not configured
> SUNW,lpvi at sbus0 slot 2 offset 0x300000 level 13 not configured
> bpp1 at sbus0 slot 2 0x200000 level 3: rev esc
> cgsix0 at sbus0 slot 3 offset 0x0 level 9: SUNW,501-2325, 1152x900, rev 11 \
> (console)data fault: pc=0xf01eb368 addr=0xc0 sfsr=1a6<PERR=0,LVL=1,AT=5,\
> FT=1,FAV,OW>
> panic: kernel fault
> halted
> 
> Program terminated
> Type  help  for more information
> ok
> 
> Anyone else see this?
> 
> Anyone got any ideas?
> 
> 				--*greywolf;
> --
> 	OpenSource is NOT exclusive to Linux.  Explore your options!
> 
> 

Jon