I have seen the same behavior on an IPX for about two months with
1.3_Alpha, Beta and now 1.3

Brad

At 2:35 AM +1100 1/11/98, Malcolm Butler wrote:
>I just installed NetBSD 1.3 on my sparc2 clone (a Trigem SDT-400),
>and now it can't seem to find the tape drive (an Archive Viper 150).
>It worked fine with the version 1.2 that I upgraded from.
>Unfortunately, I now want to get some stuff off the backup tape that
>I made prior to upgrading.
>
>There are no hardware changes during the upgrade.  I have three hard
>disk drives, and the tape is SCSI ID 4.  Probing the SCSI bus from the
>PROM monitor appears to find the tape drive successfully.
>
>However, during boot, the kernel generates some error messages (see
>below), and subsequently, attempts to use /dev/rst0 produce "device
>not configured" error messages.
>
>These are the kernel messages at boot time that relate to the SCSI
>interface:
>
>esp0 at sbus0 slot 0 offset 0x800000 pri 3: ESP100A, 20MHz, SCSI ID 7
>scsibus0 at esp0: 8 targets
>probe(esp0:0:0): max sync rate 4.03Mb/s
>sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST3610N, 9290> SCSI2 0/direct fixed
>sd0: 510MB, 1872 cyl, 7 head, 79 sec, 512 bytes/sect x 1046206 sectors
>probe(esp0:1:0): max sync rate 4.03Mb/s
>sd1 at scsibus0 targ 1 lun 0: <QUANTUM, LPS540S, 5900> SCSI2 0/direct fixed
>sd1: 516MB, 2740 cyl, 4 head, 96 sec, 512 bytes/sect x 1057616 sectors
>probe(esp0:3:0): max sync rate 4.03Mb/s
>sd2 at scsibus0 targ 3 lun 0: <MAXTOR, LXT-535S, 8.57> SCSI1 0/direct fixed
>sd2: 510MB, 1546 cyl, 11 head, 61 sec, 512 bytes/sect x 1045242 sectors
>esp0: !TC [intr 10, stat 87, step 1] prevphase 6, resid 0
>esp0: illegal command: 0x90 (state 4, phase 6, prevphase 6)
>esp0: !TC [intr 10, stat 87, step 1] prevphase 6, resid 0
>esp0: illegal command: 0x90 (state 4, phase 6, prevphase 6)
>esp0: !TC [intr 10, stat 87, step 1] prevphase 6, resid 0
>esp0: illegal command: 0x90 (state 4, phase 6, prevphase 6)
>esp0: illegal command: 0x90 (state 4, phase 6, prevphase 6)
>esp0: illegal command: 0x90 (state 4, phase 6, prevphase 6)
>esp0: illegal command: 0x90 (state 4, phase 6, prevphase 6)
>
>
>Thanks for any help.
>
>--
>Malcolm Butler               malb@bellman.apana.org.au
>The kingdom of heaven is like unto a Net  (Matt. 13,xlvii)


Stephen B. Salai                            Phone (716) 325-5553
Cumpston & Shaw                             Fax    (716) 262-3906
Two State Street                            email bsalai@tmonline.com
Rochester, NY 14614