I had some problems with the install.sh. I had done most of the work
already anyway when I realized I was supposed to use it. Here are by boot
messages. I shall try bringing a SS5 or SS20 up depending on what I can
liberate. I thought the continuing saga of the fd controller got
resolved? This is a Sparc 1+.


NetBSD 1.1 (GENERIC) #7: Tue Nov 21 20:16:32 MET 1995
    pk@neon:/usr/src1/sys/arch/sparc/compile/GENERIC
real mem = 16666624
avail mem = 14262272
using 203 buffers containing 831488 bytes of memory
bootpath: /sbus0/esp0/sd@0,0
mainbus0 (root)
cpu0 at mainbus0: Sun 4/65 (MB86900/1A or L64801 @ 25 MHz, WTL3170/2 FPU)
cpu0: 65536 byte write-through, 16 bytes/line, sw flush cache enabled
memreg0 at mainbus0 ioaddr 0xf4000000
clock0 at mainbus0 ioaddr 0xf2000000: mk48t02 (eeprom)
timer0 at mainbus0 ioaddr 0xf3000000
auxreg0 at mainbus0 ioaddr 0xf7400000
zs0 at mainbus0 ioaddr 0xf1000000 pri 12, softpri 6
zs0a: console i/o
zs1 at mainbus0 ioaddr 0xf0000000 pri 12, softpri 6
fdc0 at mainbus0 ioaddr 0xf7200000fdcresult: timeout
 CFGLOCK: unexpected response pri 11, softpri 4: chip 82077
audio0 at mainbus0 ioaddr 0xf7201000 pri 13, softpri 4
sbus0 at mainbus0 ioaddr 0xf8000000: clock = 25 MHz
dma0 at sbus0 slot 0 offset 0x400000: rev 1
esp0 at sbus0 slot 0 offset 0x800000 pri 3: ESP100 25Mhz, target 7
scsibus0 at esp0
esp0 targ 3 lun 0: <CONNER, CP30540 545MB3.5, AFBD> SCSI2 0/direct fixed
sd0 at scsibus0: 520MB, 2242 cyl, 6 head, 79 sec, 512 bytes/sec
le0 at sbus0 slot 0 offset 0xc00000 pri 5: hardware address 08:00:20:08:e8:79
cgthree0 at sbus0 slot 3 offset 0x0: SUNW,501-1718, 1152 x 900
root on sd0a
Automatic boot in progress: starting file system checks.
/dev/rsd0a: file system is clean; not checking
/dev/rsd0h: file system is clean; not checking
setting tty flags
starting network
...



  When I say "done" about disklabelling, it dies. I do not quite
understand why. I'd netbooted to disklabel.

Label which disk? [done] sd0
/tmp/EdDk.a000246: 24 lines, 668 characters.

You may label the following disks:

sd0

Label which disk? [done] 

You will now have the opportunity to specify mount points for some or
all of the partitions you have on your disk(s).
You will be prompted for device name (for example `/dev/sd0d') and
mount point (full path, e.g. `/usr').

Note that these do not have to be in any particular order.  You will
be given the opportunity to edit the resulting 'fstab' file before
any of the filesystems are mounted.  At that time you will be able
to resolve any filesystem order dependencies.

The following will be used for the root filesystem:
        sd0a    /
install.sh: syntax error at line 911: `done' unexpected
install.sh: syntax error at line 1: `)' unexpected