Port-sgimips archive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]

Re: kernel panic on IP32 R12000

Well what I do not understand is that 1) the machine boot from the install cdrom as
boot -f  pci(0)scsi(0)cdrom(4)rdisk(0)partition(8)ip3xboot
witch invokes
with this dmesg:
> boot -f pci(0)scsi(0)cdrom(4)rdisk(0)partition(8)ip3xboot
50624+1376 entry: 0x80002000

NetBSD/sgimips 4.99.49 Bootstrap, Revision 1.2
(builds@wb30, Mon Jan 21 21:48:00 PST 2008)

devopen: pci(0)scsi(0)cdrom(4)rdisk(0)partition(0) type scsi file ip3x
[ Kernel symbol table missing! ]
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
   2006, 2007, 2008
   The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
   The Regents of the University of California.  All rights reserved.

NetBSD 4.99.49 (INSTALL32_IP3x) #0: Mon Jan 21 22:58:54 PST 2008
total memory = 256 MB
(6848 KB reserved for ARCS)
avail memory = 234 MB
mainbus0 (root): SGI-IP32 [SGI, 1], 1 processor
cpu0 at mainbus0: MIPS R12000 CPU (0xe23) Rev. 2.3 with unknown FPC type (0x900)
Rev. 0.0
cpu0: 32KB/64B 2-way set-associative L1 Instruction cache, 64 TLB entries
cpu0: 32KB/32B 2-way set-associative write-back L1 Data cache
cpu0: 1024KB/64B 2-way set-associative write-back L2 Data cache
crime0 at mainbus0 addr 0x14000000: rev 1.4 (CRIME_ID: 1000000000a1)
crmfb0 at mainbus0 addr 0x16000000: SGI CRIME Graphics Display Engine
crmfb0: initial resolution 1280x1024
so we need 10 x 8 tiles -> 00500000
crmfb0: allocated 5242880 byte fb @ 0x80060000 (0xa17b0000)
wsdisplay0 at crmfb0 kbdmux 1
mace0 at mainbus0 addr 0x1f000000
lpt0 at mace0 offset 0x380000 intr 4 intrmask 0xf0000
com0 at mace0 offset 0x390000 intr 4 intrmask 0x3f00000: ns16550a, working fifo
com0: console
com1 at mace0 offset 0x398000 intr 4 intrmask 0xfc000000: ns16550a, working fifo
mcclock0 at mace0 offset 0x3a0000 intrmask 0x0
mec0 at mace0 offset 0x280000 intr 3 intrmask 0x0: MAC-110 Ethernet, rev 1
mec0: Ethernet address 08:00:69:0e:85:21
nsphy0 at mec0 phy 8: DP83840 10/100 media interface, rev. 1
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
mavb0 at mace0 offset 0x300000 intr 6 intrmask 0x0: can't power up conversion re
macepci0 at mace0 offset 0x80000 intr 7 intrmask 0x0: rev 1
pci0 at macepci0 bus 0
ahc0 at pci0 dev 1 function 0: Adaptec aic7880 Ultra SCSI adapter
ahc0: interrupting at crime interrupt 8
ahc0: Using left over BIOS settings
ahc0: Host Adapter has no SEEPROM. Using default SCSI target parameters
ahc0: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
scsibus0 at ahc0: 16 targets, 8 luns per target
ahc1 at pci0 dev 2 function 0: Adaptec aic7880 Ultra SCSI adapter
ahc1: interrupting at crime interrupt 9
ahc1: Using left over BIOS settings
ahc1: Host Adapter has no SEEPROM. Using default SCSI target parameters
ahc1: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
scsibus1 at ahc1: 16 targets, 8 luns per target
md0: internal 4096 KB image area
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 2 lun 0: <SGI, IBM DDRS-39130W, S95D> disk fixed
sd0: 8682 MB, 8387 cyl, 10 head, 212 sec, 512 bytes/sect x 17781520 sectors
sd0: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers, tagged queueing
cd0 at scsibus0 target 4 lun 0: <TOSHIBA, DVD-ROM SD-M1401, 1F09> cdrom removable
cd0: sync (50.00ns offset 15), 8-bit (20.000MB/s) transfers
sd1 at scsibus1 target 2 lun 0: <SEAGATE, ST318275LW, 0001> disk fixed
sd1: 17366 MB, 11721 cyl, 10 head, 303 sec, 512 bytes/sect x 35566480 sectors
sd1: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers, tagged queueing
boot device: sd0
root on md0a dumps on md0b
root file system type: ffs
WARNING: clock gained 5 days
warning: no /dev/console
Created mfs /dev (163 blocks, 320 inodes)
./MAKEDEV: missing ./MAKEDEV.local
tset: not found
erase ^?, werase ^W, kill ^U, intr ^C
and then goes to the install menu...
I know that it is a special kernel
why would it work when the netbsd on the install crashes if it is based on the same kernell, YES.. NO?

Michael Lorenz wrote: -----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1


On Jan 27, 2008, at 10:53, Thomas E. Spanjaard wrote:

Luc Pernot wrote:

               Processor: 300 Mhz R12000, with FPU

I wasn't aware NetBSD supported the R12k.

Is the R12k really /that/ different from the R10k?
The panic was about cache support, the R10k code might just work here.

have fun

Home | Main Index | Thread Index | Old Index