I have an extra Indy, and would like to make it available to the
project -- developers get first dibs.

It is a pretty well-cared-for and clean R4600/133MHz, 256MB, and
full dmesg is attached.

There are a pair of unrecognized GIO bus AUI network cards inside.

It has 2.0.2 installed, and has built its own world in the past,
so I believe the hardware is reasonably solid.  One of the 2
disks is kinda noisy though, so YMMV there.

The Indy is located in Sunnyvale, California, USA.  I'm guessing
it would cost around $30 to ship it inside the USA; I'm not sure
it's worth it to ship outside USA, but if someone is truly
desparate to have it and willing to pay the expense, I'll send
it overseas.

Cheers,
sr.
-- 


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 2.0.2 (GENERIC32_IP2x) #0: Wed Mar 23 00:18:26 UTC 2005
	jmc@faith.netbsd.org:/home/builds/ab/netbsd-2-0-2-RELEASE/sgimips/200503220140Z-obj/home/builds/ab/netbsd-2-0-2-RELEASE/src/sys/arch/sgimips/compile/GENERIC32_IP2x
total memory = 256 MB
(768 KB reserved for ARCS)
avail memory = 245 MB
mainbus0 (root): SGI-IP22 [SGI, 6908785c], 1 processor
cpu0 at mainbus0: QED R4600 Orion CPU (0x2020) Rev. 2.0 with built-in FPU Rev. 2.0
cpu0: 16KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries
cpu0: 16KB/32B 2-way set-associative write-back L1 Data cache
ioc0 at mainbus0 addr 0x1fbd9800: rev 0, machine Indy (Guiness), board rev 0
int0 at mainbus0 addr 0x1fbd9880: bus 66MHz, CPU 133MHz
imc0 at mainbus0 addr 0x1fa00000: revision 3
gio0 at imc0
newport0 at gio0 slot 2 addr 0x1f000000: SGI NG1 (board revision 7, cmap revision 7, xmap revision 7, vc2 revision 0), depth 8
wsdisplay0 at newport0 kbdmux 1
wsmux1: connecting to wsdisplay0
hpc0 at gio0 addr 0x1fb80000: SGI HPC3
zsc0 at hpc0 offset 0x59830
zstty0 at zsc0 channel 1 (console i/o)
zstty1 at zsc0 channel 0
pckbc0 at hpc0 offset 0x59840
sq0 at hpc0 offset 0x54000: SGI Seeq 80c03
sq0: Ethernet address 08:00:69:08:78:5c
wdsc0 at hpc0 offset 0x44000: WD33C93B SCSI, rev=0, target 0
scsibus0 at wdsc0: 8 targets, 8 luns per target
dsclock0 at hpc0 offset 0x60000
haltwo0 at hpc0 offset 0x58000: HAL2 revision 4.1.0
audio0 at haltwo0: half duplex
hpc1 at gio0 addr 0x1fb00000: SGI HPC3
zsc at hpc1 offset 0x59830 not configured
pckbc at hpc1 offset 0x59840 not configured
sq at hpc1 offset 0x54000 not configured
wdsc at hpc1 offset 0x44000 not configured
dsclock at hpc1 offset 0x60000 not configured
haltwo at hpc1 offset 0x58000 not configured
hpc2 at gio0 addr 0x1f980000: SGI HPC3
zsc at hpc2 offset 0x59830 not configured
pckbc at hpc2 offset 0x59840 not configured
sq at hpc2 offset 0x54000 not configured
wdsc at hpc2 offset 0x44000 not configured
dsclock at hpc2 offset 0x60000 not configured
haltwo at hpc2 offset 0x58000 not configured
biomask 07 netmask 07 ttymask 0f clockmask bf
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 1 lun 0: <SEAGATE, ST34555N, 0930> disk fixed
sd0: 4340 MB, 6300 cyl, 8 head, 176 sec, 512 bytes/sect x 8888924 sectors
sd0: sync (200.00ns offset 12), 8-bit (5.000MB/s) transfers, tagged queueing
sd1 at scsibus0 target 2 lun 0: <SGI, SEAGATE ST31200N, 9278> disk fixed
sd1: 1014 MB, 2700 cyl, 9 head, 85 sec, 512 bytes/sect x 2077833 sectors
sd1: sync (200.00ns offset 12), 8-bit (5.000MB/s) transfers, tagged queueing
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs