Synology DS109+ booting NetBSD (to root prompt)

[Matt Thomas <matt%3am-software.com@localhost>]

U-Boot 1.3.3 (Dec  1 2008 - 22:03:05)

CPU:   8533, Version: 1.1, (0x80340011)
Core:  E500, Version: 2.2, (0x80210022)
Clock Configuration:
      CPU:1067 MHz, CCB: 534 MHz,
      DDR: 267 MHz (534 MT/s data rate), LBC:  33 MHz
L1:    D-cache 32 kB enabled
      I-cache 32 kB enabled
I2C:   ready
DRAM:  Initializing
   DDR: 512 MB
FLASH:  4 MB
L2 cache 256KB: enabled
Using default environment

In:    serial
Out:   serial
Err:   serial

CPLD revision: 1.0
Synology Model: DS-109+
DRAM Type: DIMM
Fan Status: Good

Net:   SK98#0
Press Ctrl+C to abort autoboot in 2 second
DS109p>setenv serverip 192.168.7.118
DS109p>setenv ipaddr 192.168.7.145
DS109p>tftp 20000 synology.bin
Using SK98#0 device
TFTP from server 192.168.7.118; our IP address is 192.168.7.145
Filename 'synology.bin'.
Load address: 0x20000
Loading: #################################################################
        #################################################################
        #################################################################
        ###################################################
done
Bytes transferred = 3607196 (370a9c hex)
DS109p>go 20000
## Starting application at 0x00020000 ...
initppc(0x20000, 0x3b6000, 0x1, 0x1ff9837c, 0x1ff9837c, 0xfffffffe)<enter> 
consdev=<> cmdline=<> root= porpllsr=0x00c48020 sys_clk=33333333 
comcnfreq=533333328 openpic-reset(ctpr=15) cache(DC=32KB/32,IC=32KB/32) bptr=0 
memprobe=512MB e500_tlbinit(0x3b6000,512MB) hid0=0x80004080/0x80804080 
hid1=0xc4003000 pordevsr=0x2a220860 devdisr=0x7000008 msgbuf=0x1fffe000 
exception_init=0x2c0f24 kv_nsegtabs=0x38 kv_segtabs=0x3b6000 
uvm_page_physload(0x3ee,0x1fffd,0x3ee,0x1fffd,0)powerpc_fixup_stubs: 786 fixups 
done in 619058 cycles
initppc done!
Loaded initial symtab at 0x327548, strtab at 0x354568, # entries 11426
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
   2006, 2007, 2008, 2009, 2010, 2011, 2012
   The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
   The Regents of the University of California.  All rights reserved.

NetBSD 6.99.10 (SYNOLOGY-$Revision: 1.13 $)
total memory = 512 MB
avail memory = 498 MB
cprng kernel: WARNING insufficient entropy at creation.
mainbus0 (root)
cpunode0 at mainbus0 node 0
cpunode0: 256KB/32B 4-banked 8-way unified L2 cache
cpu0 at cpunode0
cpu0: 1.06 GHz MPC8533 1.1 with an e500v2 2.2 core, ID 0 (Primary)
cpu0: 32KB/32B 8-way L1 data cache
cpu0: 32KB/32B 8-way L1 instruction cache
cpu0: 2 TLBs, 3 concurrent 8-bit PIDs (256 total)
cpu0: tlb0: 512 fixed-size (4KB) 4-way set associative entries
cpu0: tlb1: 16 variable-size (4KB..4GB) fully associative entries
e500wdog0 at cpunode0: default period is 5 seconds (wdog is active)
duart0 at cpunode0: 2 ports
com0 at duart0 port 1: ns16550a, working fifo
com0: console
com1 at duart0 port 2: ns16550a, working fifo
duart0: interrupting on irq 26
tsec at cpunode0 instance 1 not configured
tsec at cpunode0 instance 2 not configured
diic0 at cpunode0: 2 ports
iic0 at diic0: I2C bus
iic1 at diic0: I2C bus
diic0: interrupting on irq 27
gpio at cpunode0 not configured
ddrc at cpunode0 not configured
obio0 at cpunode0: 2 of 8 ports enabled
obio0: cs0: 4MB 8-bit GPCM region at 0xffc00000
obio0: cs1: 32KB 8-bit GPCM region at 0xf8000000
pq3pcie0 at cpunode0 instance 1: PCI-Express x4 controller
pci0 at pq3pcie0 bus 0
ppb0 at pci0 dev 0 function 0: Freescale Semiconductor product 0x0031 (rev. 
0x11)
ppb0: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci1 at ppb0 bus 1
siisata0 at pci1 dev 0 function 0: CMD Technology SiI3132 SATALink (rev. 0x01)
siisata0: interrupting at msi 1
atabus0 at siisata0 channel 0
atabus1 at siisata0 channel 1
pcie at cpunode0 instance 2 not configured
pcie at cpunode0 instance 3 not configured
pq3pci0 at cpunode0: 32-bit PCI controller
pci2 at pq3pci0 bus 0
Freescale Semiconductor product 0x0031 (PowerPC processor, revision 0x11) at 
pci2 dev 0 function 0 not configured
ohci0 at pci2 dev 14 function 0: NEC USB Host Controller (rev. 0x44)
csr: 02100006
ohci0: interrupting at extirq 0
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
ehci0 at pci2 dev 14 function 1: NEC USB2 Host Controller (rev. 0x05)
ehci0: interrupting at extirq 0
ehci0: companion controller, 3 ports each: ohci0
usb1 at ehci0: USB revision 2.0
skc0 at pci2 dev 15 function 0: extirq 0
skc0: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
sk0 at skc0 port A: Ethernet address 00:11:22:33:44:54
makphy0 at sk0 phy 0: Marvell 88E1011 Gigabit PHY, rev. 5
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
cpunode0: 8 input pins, 8 output pins
gpio0 at cpunode0: 8 pins
gpio1 at cpunode0: 8 pins
uhub0 at usb0: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1 at usb1: NEC EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
siisata0 port 0: device present, speed: 3.0Gb/s
wd0 at atabus0 drive 0
wd0: <ST3250312AS>
wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
cprng sysctl: WARNING insufficient entropy at creation.

Not sure the PCI irqs are correct.  But it's a start!