At 12:40 PM 6/28/2002, Markus W Kilbinger wrote:
>Hi!
>
>... with:
>
>   NetBSD 1.6B (MATHILDA) #1: Fri Jun 28 21:40:26 MEST 2002
>       kilbi@qie:/usr/src/sys/arch/macppc/compile/MATHILDA
>   total memory = 256 MB
>   avail memory = 228 MB
>   using 2048 buffers containing 13208 KB of memory
>   mainbus0 (root)
>   cpu0 at mainbus0: 7410 (Revision 1.3), ID 0 (primary)
>   cpu0: HID0 8094c0a4<EMCP,DOZE,DPM,EIEC,ICE,DCE,SGE,BTIC,BHT>
>   cpu0: 500.00 MHz
>   cpu0: 1MB backside cache
>   uninorth0 at mainbus0
>   pci0 at uninorth0 bus 0
>   ...
>   boot device: wd0
>   root on wd0a dumps on wd0b
>   root file system type: ffs
>   exec /sbin/init: error 14
>   init: not found
>   panic: no init

Works for me.  Try doing a make clean first.  [For those
that follow port-powerpc, this include the new ppc code
collapse I've been working on.]  Uh, make sure you aren't
using OLDPMAP in your config file.

NetBSD 1.6B (CURRENT) #93: Fri Jun 28 20:17:50 UTC 2002
     mthomas@muck1:/u1/kobj/CURRENT
total memory = 1536 MB
avail memory = 1475 MB
using 768 buffers containing 3072 KB of memory
mainbus0 (root)
cpu0 at mainbus0: 7450 (Revision 2.0), ID 0 (primary)
cpu0: HID0 8450c09c<EMCP,TBEN,NAP,DPM,ICE,DCE,SGE,LRSTK,FOLD,BHT>
cpu0: 733.34 MHz
cpu0: 256KB L2 cache
uninorth0 at mainbus0
pci0 at uninorth0 bus 0
pci0: i/o space, memory space enabled
Apple Computer UniNorth AGP Interface (host bridge) at pci0 dev 11 function 
0 no
t configured
uninorth1 at mainbus0
pci1 at uninorth1 bus 0
pci1: i/o space, memory space enabled
Apple Computer UniNorth Host-PCI Bridge (host bridge) at pci1 dev 11 
function 0
not configured
ppb0 at pci1 dev 18 function 0: Digital Equipment DECchip 21152 PCI-PCI 
Bridge (
rev. 0x03)
pci2 at ppb0 bus 1
pci2: i/o space, memory space enabled
tlp0 at pci2 dev 4 function 0: DECchip 21143 Ethernet, pass 4.1
tlp0: interrupting at irq 52
tlp0: Ethernet address 00:80:c8:b9:70:71
nsphyter0 at tlp0 phy 1: DP83843 10/100 media interface, rev. 0
nsphyter0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
tlp1 at pci2 dev 5 function 0: DECchip 21143 Ethernet, pass 4.1
tlp1: interrupting at irq 52
tlp1: Ethernet address 00:80:c8:b9:70:72
nsphyter1 at tlp1 phy 1: DP83843 10/100 media interface, rev. 0
nsphyter1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
tlp2 at pci2 dev 6 function 0: DECchip 21143 Ethernet, pass 4.1
tlp2: interrupting at irq 52
tlp2: Ethernet address 00:80:c8:b9:70:73
nsphyter2 at tlp2 phy 1: DP83843 10/100 media interface, rev. 0
nsphyter2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
tlp3 at pci2 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1
tlp3: interrupting at irq 52
tlp3: Ethernet address 00:80:c8:b9:70:74
nsphyter3 at tlp3 phy 1: DP83843 10/100 media interface, rev. 0
nsphyter3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ppb1 at pci1 dev 19 function 0: Digital Equipment DECchip 21152 PCI-PCI 
Bridge (
rev. 0x03)
pci3 at ppb1 bus 2
pci3: i/o space, memory space enabled
tlp4 at pci3 dev 4 function 0: DECchip 21143 Ethernet, pass 4.1
tlp4: interrupting at irq 53
tlp4: Ethernet address 00:80:c8:b9:8f:99
nsphyter4 at tlp4 phy 1: DP83843 10/100 media interface, rev. 0
nsphyter4: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
tlp5 at pci3 dev 5 function 0: DECchip 21143 Ethernet, pass 4.1
tlp5: interrupting at irq 53
tlp5: Ethernet address 00:80:c8:b9:8f:9a
nsphyter5 at tlp5 phy 1: DP83843 10/100 media interface, rev. 0
nsphyter5: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
tlp6 at pci3 dev 6 function 0: DECchip 21143 Ethernet, pass 4.1
tlp6: interrupting at irq 53
tlp6: Ethernet address 00:80:c8:b9:8f:9b
nsphyter6 at tlp6 phy 1: DP83843 10/100 media interface, rev. 0
nsphyter6: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
tlp7 at pci3 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1
tlp7: interrupting at irq 53
tlp7: Ethernet address 00:80:c8:b9:8f:9c
nsphyter7 at tlp7 phy 1: DP83843 10/100 media interface, rev. 0
nsphyter7: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
lmc0 at pci1 dev 21 function 0: Lan Media Corporation DS3
lmc0: interrupting at irq 58
lmc0: pass 2.2, serial 00:60:99:00:14:fc, irq 58
obio0 at pci1 dev 23 function 0: addr 0x80000000
zsc0 at obio0 offset 0x13000: irq 22,23
zstty0 at zsc0 channel 0 (console)
zstty1 at zsc0 channel 1
i2s at obio0 offset 0x10000 not configured
adb0 at obio0 offset 0x16000 irq 47: pm_adb_op: timeout. command = 0x0
0 targets
wdc0 at obio0 offset 0x1f000 irq 19: DMA transfer
wd0 at wdc0 channel 0 drive 0: <Maxtor 92049U3>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 19536 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 40010544 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd1 at wdc0 channel 0 drive 1: <IBM-DTLA-305020>
wd1: drive supports 16-sector PIO transfers, LBA addressing
wd1: 19623 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 40188960 sectors
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
ata4 conf[0] = 0xc519465, cyc = 2 (30 ns), act = 6 (90 ns), inact = 3
ata4 conf[1] = 0xc519465, cyc = 2 (30 ns), act = 6 (90 ns), inact = 3
wd0(wdc0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66) 
(using
DMA data transfers)
wd1(wdc0:0:1): using PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66) 
(using
DMA data transfers)
wdc1 at obio0 offset 0x20000 irq 20: DMA transfer
atapibus0 at wdc1 channel 0: 2 targets
cd0 at atapibus0 drive 0: <SONY    CD-RW  CRX155E, , 1.0c> type 5 cdrom 
removabl
e
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
conf[0] = 0x11823, cyc = 4 (120 ns), act = 3 (75 ns), inact = 1
cd0(wdc1:0:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
wdc2 at obio0 offset 0x21000 irq 21: DMA transfer
Apple Computer KeyLargo USB Controller (USB serial bus, interface 0x10) at 
pci1
dev 24 function 0 not configured
Apple Computer KeyLargo USB Controller (USB serial bus, interface 0x10) at 
pci1
dev 25 function 0 not configured
uninorth2 at mainbus0
pci4 at uninorth2 bus 0
pci4: i/o space, memory space enabled
Apple Computer UniNorth Host-PCI Bridge (host bridge) at pci4 dev 11 
function 0
not configured
Lucent Technologies product 0x5811 (Firewire serial bus, interface 0x10) at 
pci4
  dev 14 function 0 not configured
gem0 at pci4 dev 15 function 0: Apple Computer GMAC Ethernet (rev. 0x01)
gem0: interrupting at irq 41
gem0: Ethernet address 00:03:93:53:ea:be, 10KB RX fifo, 4KB TX fifo
brgphy0 at gem0 phy 0: BCM5411 1000BASE-T media interface, rev. 1
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FD
X, auto
lmc0: physical link up
boot device: wd1
root on wd1a dumps on wd1b
root file system type: ffs



-- 
Matt Thomas               Internet:   matt@3am-software.com
3am Software Foundry      WWW URL:    http://www.3am-software.com/bio/matt/
Cupertino, CA             Disclaimer: I avow all knowledge of this message