Hi.
I am newbi.

I try to install NetBSD via FTP on my Power Center 150.
It boot up  from floppy.

The problem is that it can not ping.
Even it  can not  ping localhost.

> mc0 at obio0 offset 0x11000: irq 14,2,3: address 00:05:9a:20:df:7b
There is a NIC and the other machines can send packets to this machine.
What is the problem?  What should I do next?

I try 1.4.1 and 1.4.2.
Both of them comes the same results.

Thank you for your time and any help would be greatly appreciated.

The below is boot log.
-
NetBSD 1.4.2 (INSTALL) #0: Wed Mar 15 22:11:01 PST 2000
    toddpw@leia.toddpw.net:/usr/src/sys/arch/macppc/compile/INSTALL
CPU: 604 (Revision 303)
real mem  = 41943040
avail mem = 32804864
using 800 buffers containing 3276800 bytes of memory
no active packagemainbus0 (root)
cpu0 at mainbus0
pci0 at mainbus0 bus 0
pci0: i/o enabled, memory enabled
pchb0 at pci0 dev 11 function 0
pchb0: vendor 0x106b product 0x0001 (rev. 0x03)
obio0 at pci0 dev 16 function 0: addr 0xf3000000
esp0 at obio0 offset 0x10000 irq 12: NCR53C94, 25MHz, SCSI ID 7
scsibus0 at esp0: 8 targets, 8 luns per target
probe(esp0:0:0): max sync rate 6.25Mb/s
sd0 at scsibus0 targ 0 lun 0: <IBM, DCAS-32160, S61A> SCSI2 0/direct
fixed
sd0: 2063MB, 8188 cyl, 3 head, 172 sec, 512 bytes/sect x 4226725
sectors
probe(esp0:3:0): max sync rate 6.25Mb/s
probe(esp0:3:0): esp0: timed out [ecb 0xe00b78c8 (flags 0x7, dleft 20,
stat 2)],
 <state 4, nexus 0xe00b78c8, phase(l 1, c 1, p 1), resid 20, msg(q 0,o
0) DMA ac
tive>
probe(esp0:3:0): sync negotiation disabled
probe(esp0:3:0): esp0: timed out [ecb 0xe00b78c8 (flags 0x47, dleft
20, stat 2)]
, <state 4, nexus 0xe00b78c8, phase(l 1, c 1, p 1), resid 20, msg(q
20,o 0) DMA
active> AGAIN
esp0: SCSI bus reset
esp0: illegal command: 0x42 (state 2, phase 3, prevphase 1)
esp0: SCSI bus reset
esp0: illegal command: 0x42 (state 2, phase 3, prevphase 1)
esp0: SCSI bus reset
esp0: illegal command: 0x42 (state 2, phase 3, prevphase 1)
probe(esp0:4:0): max sync rate 6.25Mb/s
esp0: illegal command: 0x42 (state 2, phase 3, prevphase 1)
esp0: SCSI bus reset
probe(esp0:4:0): max sync rate 6.25Mb/s
esp0: illegal command: 0x42 (state 2, phase 3, prevphase 1)
probe(esp0:4:0): max sync rate 6.25Mb/s
esp0: illegal command: 0x42 (state 2, phase 3, prevphase 1)
esp0: SCSI bus reset
probe(esp0:4:0): max sync rate 6.25Mb/s
esp0: illegal command: 0x42 (state 2, phase 3, prevphase 1)
sd1 at scsibus0 targ 5 lun 0: <IOMEGA, ZIP 100, E.08> SCSI2 0/direct
removable
sd1: drive offline
mc0 at obio0 offset 0x11000: irq 14,2,3: address 00:05:9a:20:df:7b
zsc0 at obio0 offset 0x13000: irq 15,16
zstty0 at zsc0 channel 0 (console)
zstty1 at zsc0 channel 1
awacs at obio0 offset 0x14000 not configured
swim3 at obio0 offset 0x15000 not configured
adb0 at obio0 offset 0x16000 irq 18: 2 targets
akbd0 at adb0 addr 2: extended keyboard
wskbd0 at akbd0
ams0 at adb0 addr 3: EMP trackball <LT02> 3-button, 200 dpi
wsmouse at ams0 not configured
nvram0 at obio0 offset 0x1d000
md0: internal 1600K image area
boot device: <unknown>
root on md0a dumps on md0b
-
Kazutaka Uemura
hamadryad@bigfoot.com