Hi all

I just tried the DUOTEST kernel on my PB230. 

It doesn't want to boot unless I set a serial console. 

Here is the output on the serial console. It is the same when I try to use
the internal screen but I get a hang at the ******** which I added to the
dump

Any ideas???

Bootstrapping NetBSD/mac68k.
Getting mapping from MMU.
System RAM: 12582912 bytes in 3072 pages.
     Low = 0x0, high = 0xc00000
Checking for Internal Video   PB/IIvx (0x60?00000) internal video at addr 0x60000000 (phys 0x60000000), len 0x8000.
Done.
Bootstrapping the pmap system.
Pmap bootstrapped.
Moving ROMBase from 0x40800000 to 0x9e0000.
Video address 0x60000000 -> 0xbe0000.
[ preserving 360017 bytes of netbsd a.out symbol table ]
Copyright (c) 1996, 1997, 1998, 1999
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.4.1 (DUOTEST) #10: Wed Nov 17 05:04:19 PST 1999
    root@duo230.axlight.com:/usr/src/sys.1.4.1/arch/mac68k/compile/DUOTEST
Apple Macintosh PowerBook Duo 230  (68030)
cpu: delay factor 166
real mem = 12582912
avail mem = 8421376
using 179 buffers containing 733184 bytes of memory
mrg: kernel has no ROM vectors for this machine!
mainbus0 (root)
obio0 at mainbus0
adb0 at obio0 (direct, PowerBook): 2 targets
aed0 at adb0 addr 0: ADB Event device
kbd0 at adb0 addr 2: PowerBook keyboard
ms0 at adb0 addr 3: EMP trackball <PG&E> 2-button, 100 dpi
asc0 at obio0: Apple Sound Chip
intvid0 at obio0 @ 60000000: On-board video
********* ^-- I hang here on internal video boot!
intvid0: 640 x 400, 16 color
grf0 at intvid0
ite0 at grf0 (minimal console)
iwm0 at obio0: Apple GCR floppy disk controller
fd0 at iwm0 drive 0: (HD disk -- not supported)
fd1 at iwm0 drive 1: (HD disk -- not supported)
ncrscsi0 at obio0
scsibus0 at ncrscsi0: 8 targets, 8 luns per target
sd0 at scsibus0 targ 0 lun 0: <IBM, WDS2120, S140> SCSI1 0/direct fixed
sd0: 120MB, 1242 cyl, 4 head, 49 sec, 512 bytes/sect x 245760 sectors
zsc0 at obio0 chip type 0 
zsc0 channel 0: d_speed   9600 DCD clk 0 CTS clk 0
zstty0 at zsc0 channel 0 (console)
zsc0 channel 1: d_speed   9600 DCD clk 0 CTS clk 0
zstty1 at zsc0 channel 1
nubus0 at mainbus0
fpu0 at mainbus0 (emulator)
boot device: sd0
root device (default sd0a): 



Thanks

Alex

--
Alex Barclay                    E-mail: alex@tfo-consulting.com
TFO Consulting			Tel:	+1 719 635 7752
2121 Mt Washington Ave
Colorado Springs, CO 80906