Trouble with NetBSD 4.0 MP on a Asus CUR-DLS

[Pierre Pronchery <khorben%defora.org@localhost>]

                Hello,

I have trouble booting NetBSD 4.0 MP on the Asus CUR-DLS mainboard,
actually extracted from a HP Netserver E800. It runs the latest BIOS I
could find on HP website.

As dumped below, when dealing with ACPI the system hits a breakpoint (if
I understand correctly, it comes from the system's ACPI, not the
kernel). If I tell the kernel to continue anyway, I get a page fault
shortly before starting init.

Is there anything I can do to fix this?

Cheers,
-- 
khorben

booting hd0a:/netbsd.mp
8987016+408068+354900 [438672+421647]=0xa20874
kenter: 0x00002000
acpi: wakecode is installed at 0x2000, size=376
BIOS CFG: Model-SubM-Rev: fc-01-00, 0x74<EBDA,KBDINT,RTC,IC2>
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.0_STABLE (GENERIC.MP) #0: Fri Feb 15 01:14:15 CET 2008
        
root%beast.defora.lan@localhost:/usr/obj/sys/arch/i386/compile/GENERIC.MP
total memory = 2047 MB
rbus: rbus_min_start set to 0x80000000
avail memory = 2001 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfd8b0
mainbus0 (root)
cpu0 at mainbus0: apid 3 (boot processor)
cpu0: Intel Pentium III (686-class), 1000.09 MHz, id 0x686
cpu0: calibrating local timer
cpu0: apic clock running at 133 MHz
cpu1 at mainbus0: apid 0 (application processor)
cpu1: starting
cpu1: Intel Pentium III (686-class), 1000.04 MHz, id 0x686
ioapic0 at mainbus0 apid 1 (I/O APIC)
ioapic0: pa 0xfec00000, version 11, 16 pins
ioapic1 at mainbus0 apid 2 (I/O APIC)
ioapic1: pa 0xfec01000, version 11, 16 pins
acpi0 at mainbus0: Advanced Configuration and Power Interface
Executed AML Breakpoint opcode
Stopped in pid 0.1 (swapper) at netbsd:cpu_Debugger+0x4:        popl    %ebp
db{3}> continue
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
ACPI-Safe 32-bit timer
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
PNP0A03 [PCI/PCI-X Host Bridge] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0A05 [Generic Container Device] at acpi0 not configured
PNP0200 [AT DMA Controller] at acpi0 not configured
PNP0000 [AT Interrupt Controller] at acpi0 not configured
npx1 at acpi0 (PNP0C04)
npx1: io 0xf0-0xfe irq 13
attimer1 at acpi0 (PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
pcppi1 at acpi0 (PNP0800)
pcppi1: io 0x61
pcppi1: children must have an explicit unit
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
PNP0C01 [System Board] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
PNP0A06 [Generic Container Device] at acpi0 not configured
pckbc1 at acpi0 (PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (PNP0F13): aux port
pckbc2: irq 12
PNP0B00 [AT Real-Time Clock] at acpi0 not configured
PNP0501 [16550A-compatible COM port] at acpi0 not configured
PNP0501 [16550A-compatible COM port] at acpi0 not configured
PNP0400 [Standard LPT printer port] at acpi0 not configured
PNP0700 [PC standard floppy disk controller] at acpi0 not configured
PNP0A03 [PCI/PCI-X Host Bridge] at acpi0 not configured
pcppi1: attached to attimer1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0 mux 1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: ServerWorks CNB20-HE PCI/AGP bridge (rev. 0x06)
pchb1 at pci0 dev 0 function 1
pchb1: ServerWorks CNB20-HE PCI/AGP bridge (rev. 0x06)
pci1 at pchb1 bus 5
pci1: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
hptide0 at pci1 dev 4 function 0
hptide0: Triones/Highpoint HPT370 IDE Controller
hptide0: bus-master DMA support present
hptide0: primary channel wired to native-PCI mode
hptide0: using ioapic1 pin 7 (irq 12) for native-PCI interrupt
atabus0 at hptide0 channel 0
hptide0: secondary channel wired to native-PCI mode
atabus1 at hptide0 channel 1
esiop0 at pci1 dev 5 function 0: Symbios Logic 53c896 (ultra2-wide scsi)
esiop0: using on-board RAM
esiop0: interrupting at ioapic1 pin 8 (irq 9)
scsibus0 at esiop0: 16 targets, 8 luns per target
esiop1 at pci1 dev 5 function 1: Symbios Logic 53c896 (ultra2-wide scsi)
esiop1: using on-board RAM
esiop1: interrupting at ioapic1 pin 9 (irq 11)
scsibus1 at esiop1: 16 targets, 8 luns per target
fxp0 at pci0 dev 2 function 0: i82559 Ethernet, rev 8
fxp0: interrupting at ioapic1 pin 4 (irq 11)
fxp0: Ethernet address 00:e0:18:1e:52:8a
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sip0 at pci0 dev 4 function 0: NatSemi DP83815 10/100 Ethernet, rev 00
sip0: interrupting at ioapic1 pin 1 (irq 10)
sip0: Ethernet address 00:40:f4:5c:54:31
nsphyter0 at sip0 phy 0: DP83815 10/100 media interface, rev. 1
nsphyter0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vga1 at pci0 dev 7 function 0: ATI Technologies Rage XL (rev. 0x27)
wsdisplay0 at vga1 kbdmux 1
wsmux1: connecting to wsdisplay0
wskbd0: connecting to wsdisplay0
pcib0 at pci0 dev 15 function 0
pcib0: ServerWorks OSB4 southbridge (rev. 0x50)
rccide0 at pci0 dev 15 function 1
rccide0: ServerWorks OSB4 IDE Controller (rev. 0x00)
rccide0: bus-master DMA support present
rccide0: primary channel configured to compatibility mode
rccide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus2 at rccide0 channel 0
rccide0: secondary channel configured to compatibility mode
rccide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus3 at rccide0 channel 1
ohci0 at pci0 dev 15 function 2: ServerWorks OSB4/CSB5 USB Host Controller (rev.
 0x04)
ohci0: interrupting at ioapic0 pin 5 (irq 5)
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: ServerWorks OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
ioapic0: enabling
ioapic1: enabling
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
Kernelized RAIDframe activated
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
wd0 at atabus0 drive 0: <HDS722516VLAT80>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 153 GB, 319120 cyl, 16 head, 63 sec, 512 bytes/sect x 321672960 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(hptide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
wd1 at atabus1 drive 0: <Maxtor 6Y120P0>
wd1: drive supports 16-sector PIO transfers, LBA addressing
wd1: 114 GB, 238216 cyl, 16 head, 63 sec, 512 bytes/sect x 240121728 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd1(hptide0:1:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
wd2 at atabus2 drive 0: <WDC WD800BB-00JHC0>
wd2: drive supports 16-sector PIO transfers, LBA addressing
wd2: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd2: 32-bit data port
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd2(rccide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33) (usi
ng DMA)
wd3 at atabus3 drive 0: <SAMSUNG SP2514N>
wd3: drive supports 16-sector PIO transfers, LBA48 addressing
wd3: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
wd3: 32-bit data port
wd3: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd3(rccide0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33) (usi
ng DMA)
boot device: wd2
root on wd2a dumps on wd2b
root file system type: ffs
kernel: supervisor trap page fault, code=0
Stopped at      netbsd:i686_mtrr_reload+0x14a:  popl    %ebx
db{0}> tr
i686_mtrr_reload(c2cc3800,1,0,c2cc3800,ccaf1000) at netbsd:i686_mtrr_reload+0x14
a
cpu_init(c2cc3800,0,0,0,0) at netbsd:cpu_init+0x62
cpu_hatch(c2cc3800,0,0,0,0) at netbsd:cpu_hatch+0xa3