--=-=-=
Content-Transfer-Encoding: quoted-printable


executive summary: T60 mostly works, and I need help with wm(4) which
won't read eeprom.

I have a new Lenova Thinkpad T60 (2613-ECU).  I'm running
GENERIC.MPACPI with the addition of "foo at cardbus" for most of
what's in GENERIC_LAPTOP.  I modified rbus_min_start to 2 GB because I
have 2 GB of RAM.

With GENERIC.MPACPI, both cpus are found.

I set the builtin SATA controller to compatibility mode in the BIOS;
NetBSD did not find the "AHCI" SATA version.  Then wd0 was found
(before it was not; cd0 was there both ways).

"X -configure;<mv config file in place>;xinit" works, but on exiting
the text consoles are messed up (large font, only part of the screen
is showing).  Someone (who I won't name unless they want to speak up
in public) tells me they have a binary ATI driver working; they and I
hope to get that into pkgsrc.

I disabled the trackpad in the bios and the trackpoint and 3 buttons
work fine.

The big problem is wm0.  On Brian's machine, wm0 works fine.  The
wm(4) is on PCI Express, but the builtin ath(4) is too and that works
fine.

It seems wm(4) should print the expected and computed checksum; I'm
not sure what's going on but I suspect either failure to actually read
the eeprom or disagreement about the checksum rules.  If anyone has
clues about how to proceed with wm0 debugging, I'd appreciate it very
much.

The cbb0 errors below are mysterious.  They were much worse before I
set rbus_min_start to 2 GB.  With rbus_min_start=3D2GB and cardbus
attachments in the kernel config, ath(4) and rtw(4) worked well enough
to wiconfig -D and see local networks.  I hope tlp(4) does too; I'll
try that soon.

I haven't played with audio, bluetooth, TCPA, or the fingerprint
reader.

Thanks to Brian de Alwis for helping me with some of this, especially
in confirming that it mostly works before I ordered one.


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2=
006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.1 (GENERIC.MPACPI) #6: Tue Aug 22 15:09:47 EDT 2006
	gdt@fnord.ir.bbn.com:/n0/obj/auto-current/i386/sys/arch/i386/compile/GENER=
IC.MPACPI
total memory =3D 2046 MB
avail memory =3D 2001 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
timecounter: selected timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfd6b0
mainbus0 (root)
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel Pentium M (Yonah) (686-class), 2161.45 MHz, id 0x6e8
cpu0: features bfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features bfe9fbff<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu0: features bfe9fbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu0: features2 c1a9<SSE3,MONITOR,VMX,EST,TM2,xTPR>
cpu0: "Genuine Intel(R) CPU           T2600  @ 2.16GHz"
cpu0: I-cache 32 KB 64B/line 8-way, D-cache 32 KB 64B/line 8-way
cpu0: L2 cache 2 MB 64B/line 8-way
cpu0: using thermal monitor 1
cpu0: Enhanced SpeedStep (1404 mV)  - unknown CPU or operating point.
cpu0: calibrating local timer
cpu0: apic clock running at 166 MHz
cpu0: 64 page colors
cpu1 at mainbus0: apid 1 (application processor)
cpu1: starting
cpu1: Intel Pentium M (Yonah) (686-class), 2161.25 MHz, id 0x6e8
cpu1: features bfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu1: features bfe9fbff<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu1: features bfe9fbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu1: features2 c1a9<SSE3,MONITOR,VMX,EST,TM2,xTPR>
cpu1: "Genuine Intel(R) CPU           T2600  @ 2.16GHz"
cpu1: I-cache 32 KB 64B/line 8-way, D-cache 32 KB 64B/line 8-way
cpu1: L2 cache 2 MB 64B/line 8-way
cpu1: using thermal monitor 1
cpu1: Enhanced SpeedStep (1404 mV)  - unknown CPU or operating point.
ioapic0 at mainbus0 apid 1 (I/O APIC)
ioapic0: pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 2
ioapic0: remapped to apic 1
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId <LENOVO,TP-79   ,00001091>, AslId < LTP,00000000>
acpi0: found ECDT, GPE 28
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
timecounter: selected timecounter "ACPI-Fast" frequency 3579545 Hz quality =
1000
ACPI-Fast 24-bit timer
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C01 [System Board] at acpi0 not configured
acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PNP0C0E): ACPI Sleep Button
PNP0A08 [PCI Express/PCI-X Mode-2 Host Bridge] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configu=
red
PNP0000 [AT Interrupt Controller] at acpi0 not configured
attimer1 at acpi0 (PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
PNP0103 [HPET Timer] at acpi0 not configured
PNP0200 [AT DMA Controller] at acpi0 not configured
pcppi1 at acpi0 (PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx0 at acpi0 (PNP0C04)
npx0: io 0xf0 irq 13
npx0: using exception 16
PNP0B00 [AT Real-Time Clock] at acpi0 not configured
pckbc0 at acpi0 (PNP0303): kbd port
pckbc0: io 0x60,0x64 irq 1
pckbc1 at acpi0 (IBM0057): aux port
pckbc1: irq 12
ATM1200 at acpi0 not configured
acpiec0 at acpi0 (PNP0C09-0): ACPI Embedded Controller
acpiec0: io 0x62,0x66
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
acpibat0 at acpi0 (PNP0C0A-0): ACPI Battery (Control Method)
acpiacad0 at acpi0 (ACPI0003-0): ACPI AC Adapter
IBM0068 at acpi0 not configured
acpitz0 at acpi0: ACPI Thermal Zone
acpitz0: unable to get polling interval; using default of 30.0s
acpitz0: passive cooling mode only
acpitz0: critical 127.0C
acpitz1 at acpi0: ACPI Thermal Zone
acpitz1: unable to get polling interval; using default of 30.0s
acpitz1: critical 99.0C passive 57.0C
pcppi1: attached to attimer1
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82945GM/PM/GMS Host Bridge (rev. 0x03)
agp0 at pchb0: can't find internal VGA device config space
ppb0 at pci0 dev 1 function 0: Intel product 0x27a1 (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci1 dev 0 function 0: ATI Technologies product 0x7145 (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 17 (irq 11)
azalia0: host: Intel 82801GB/GR High Definition Audio Controller (rev. 2)
azalia0: host: High Definition Audio rev. 1.0
ppb1 at pci0 dev 28 function 0: Intel 82801GB/GR PCI Express Port #1 (rev. =
0x02)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
wm0 at pci2 dev 0 function 0: Intel i82573L Gigabit Ethernet, rev. 0
wm0: interrupting at ioapic0 pin 16 (irq 11)
wm0: PCI-Express bus
wm0: No EEPROM
wm0: unable to read Ethernet address
ppb2 at pci0 dev 28 function 1: Intel 82801GB/GR PCI Express Port #2 (rev. =
0x02)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ath0 at pci3 dev 0 function 0
ath0: interrupting at ioapic0 pin 17 (irq 11)
ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbp=
s 36Mbps 48Mbps 54Mbps
ath0: mac 10.3 phy 6.1 radio 10.2
ppb3 at pci0 dev 28 function 2: Intel 82801GB/GR PCI Express Port #3 (rev. =
0x02)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci0 dev 28 function 3: Intel 82801GB/GR PCI Express Port #4 (rev. =
0x02)
pci5 at ppb4 bus 12
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
uhci0 at pci0 dev 29 function 0: Intel 82801GB/GR USB UHCI Controller (rev.=
 0x02)
uhci0: interrupting at ioapic0 pin 16 (irq 11)
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801GB/GR USB UHCI Controller (rev.=
 0x02)
uhci1: interrupting at ioapic0 pin 17 (irq 11)
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801GB/GR USB UHCI Controller (rev.=
 0x02)
uhci2: interrupting at ioapic0 pin 18 (irq 11)
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3: Intel 82801GB/GR USB UHCI Controller (rev.=
 0x02)
uhci3: interrupting at ioapic0 pin 19 (irq 11)
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: Intel 82801GB/GR USB EHCI Controller (rev.=
 0x02)
ehci0: interrupting at ioapic0 pin 19 (irq 11)
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb5 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0xe2)
pci6 at ppb5 bus 21
pci6: i/o space enabled
cbb0 at pci6 dev 0 function 0: Texas Instruments PCI1510 PCI-CardBus Bridge=
 (rev. 0x00)
cbb0: can't map socket base address 0xe4300000
pci_io_find: expected type i/o, found mem
cbb0: can't map socket base address 0xc2b5ba50: io mode
cbb0: interrupting at ioapic0 pin 16 (irq 11)
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 22
pcmcia0 at cardslot0
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801GBM LPC Interface Bridge (rev. 0x02)
piixide0 at pci0 dev 31 function 2
piixide0: Intel 82801GBM/GHM Serial ATA Controller (ICH7) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus1 at piixide0 channel 1
Intel 82801GB/GR SMBus Controller (SMBus serial bus, revision 0x02) at pci0=
 dev 31 function 3 not configured
isa0 at pcib0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
isapnp0: no ISA Plug 'n Play devices found
ioapic0: enabling
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[0]: Analog Devices AD1981HD (rev. 2.0)
azalia0: codec[0]: High Definition Audio rev. 1.0
azalia0: playback: max channels=3D2, encodings=3D1<PCM>
azalia0: playback: PCM formats=3De007f<24bit,20bit,16bit,48kHz,44.1kHz,32kH=
z,22.05kHz,16kHz,11.025kHz,8kHz>
azalia0: recording: max channels=3D2, encodings=3D1<PCM>
azalia0: recording: PCM formats=3D6007f<20bit,16bit,48kHz,44.1kHz,32kHz,22.=
05kHz,16kHz,11.025kHz,8kHz>
azalia0: codec[1]: 0x14f1/0x2bfa (rev. 0.0)
azalia0: codec[1]: High Definition Audio rev. 0.9
azalia0: codec[1]: No support for modem function groups
azalia0: codec[1] has no audio function groups
audio0 at azalia0: full duplex, independent
swwdog0: software watchdog initialized
Kernelized RAIDframe activated
IPsec: Initialized Security Association Processing.
ugen0 at uhub3 port 2
ugen0: STMicroelectronics Biometric Coprocessor, rev 1.00/0.01, addr 2
wd0 at atabus0 drive 0: <HTS541010G9SA00>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 95396 MB, 193821 cyl, 16 head, 63 sec, 512 bytes/sect x 195371568 sect=
ors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DM=
A)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <MATSHITADVD-RAM UJ-842, , RB01> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
cpu1: CPU 1 running
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

# inserted after boot
rtw0 at cardbus0 function 0: Realtek RTL8180 802.11 MAC/BBP
rtw0: interrupting at 11
rtw0: hardware version D
rtw0: SROM version 1.2
rtw0: RF: Philips SA2400A, PA: Philips SA2411
rtw0: analog PHY
rtw0: CS threshold 11
rtw0: Geographic Location USA
rtw0: 802.11 address [redacted]
rtw0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
rtw0 detached

ath1 at cardbus0 function 0
ath1: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath1: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath1: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbp=
s 36Mbps 48Mbps 54Mbps
ath1: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath1: mac 5.6 phy 4.1 5 GHz radio 1.7 2 GHz radio 2.3
ath1: interrupting at 11
ath1 detached

# this has never worked anywhere; it's an 802.11g USB interface
ugen1 at uhub4 port 5
ugen1: GlobespanVirata Cohiba 3887 rev0, rev 2.00/10.50, addr 2
ugen1: at uhub4 port 5 (addr 2) disconnected
ugen1 detached


=2D-=20
    Greg Troxel <gdt@ir.bbn.com>

--=-=-=
Content-Type: application/pgp-signature

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.5 (NetBSD)

iD8DBQFE62HQ+vesoDJhHiURAv2dAJ0fLWogTFDbFhCrGtra9NvCFMnmtQCaA5Hc
vwvondEfoMKXk/SDUq4Eg8g=
=Oq3h
-----END PGP SIGNATURE-----
--=-=-=--