Subject: GENERIC.MPACPI hangs on Dell Lattitude D820
To: None <port-i386@netbsd.org>
From: Petter Lindquist <pollen@astrakan.hig.se>
List: port-i386
Date: 05/29/2006 14:56:41
kernel:
ftp://ftp.netbsd.org/pub/NetBSD-daily/HEAD/200605230000Z/i386/binary/kernel=
/netbsd-GENERIC.MPACPI.gz

picture of hang: http://www.hig.se/~petter/netbsd/IMG_1084.JPG
(No, I can't go into debugger...)

Full dmesg.boot from a GENERIC.MP kernel:
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 3.99.18 (GENERIC.MP) #0: Thu May  4 07:33:37 UTC 2006

builds@b3.netbsd.org:/home/builds/ab/HEAD/i386/200605040000Z-obj/home/build=
s/ab/HEAD/src/sys/arch/i386/compile/GENERIC.MP
total memory =3D 2046 MB
avail memory =3D 2001 MB
BIOS32 rev. 0 found at 0xffa10
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium Pro, II or III (686-class), 1995.11 MHz, id 0x6e8
cpu0: features bfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features bfe9fbff<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu0: features bfe9fbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu0: features2 c1a9<SSE3,MONITOR,VMX,EST,TM2,xTPR>
cpu0: "Genuine Intel(R) CPU           T2500  @ 2.00GHz"
cpu0: I-cache 32 KB 64B/line 8-way, D-cache 32 KB 64B/line 8-way
cpu0: L2 cache 2 MB 64B/line 8-way
cpu0: using thermal monitor 1
cpu0: Enhanced SpeedStep (1004 mV)  - unknown CPU or operating point.
cpu0: 64 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel product 0x27a0 (rev. 0x03)
ppb0 at pci0 dev 1 function 0: Intel product 0x27a1 (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga1 at pci1 dev 0 function 0: NVIDIA product 0x01d8 (rev. 0xa1)
vga1: WARNING: ignoring 64-bit BAR @ 0x14
vga1: WARNING: ignoring 64-bit BAR @ 0x1c
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio
Controller
azalia0: interrupting at irq 11
azalia0: host: 82801GB/GR High Definition Audio Controller (rev. 1)
azalia0: host: High Definition Audio rev. 1.0
ppb1 at pci0 dev 28 function 0: Intel 82801GB/GR PCI Express Port #1 (rev.
0x01)
pci2 at ppb1 bus 11
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 28 function 1: Intel 82801GB/GR PCI Express Port #2 (rev.
0x01)
pci3 at ppb2 bus 12
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
Intel product 0x4222 (miscellaneous network, revision 0x02) at pci3 dev 0
function 0 not configured
ppb3 at pci0 dev 28 function 2: Intel 82801GB/GR PCI Express Port #3 (rev.
0x01)
pci4 at ppb3 bus 9
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
bge0 at pci4 dev 0 function 0: Broadcom BCM5752 Gigabit Ethernet
bge0: interrupting at irq 5
bge0: firmware handshake timed out, val =3D 0
bge0: RX CPU self-diagnostics failed!
bge0: chip initialization failed
ppb4 at pci0 dev 28 function 3: Intel 82801GB/GR PCI Express Port #4 (rev.
0x01)
pci5 at ppb4 bus 13
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
uhci0 at pci0 dev 29 function 0: Intel 82801GB/GR USB UHCI Controller
(rev. 0x01)
uhci0: interrupting at irq 10
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801GB/GR USB UHCI Controller
(rev. 0x01)
uhci1: interrupting at irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801GB/GR USB UHCI Controller
(rev. 0x01)
uhci2: interrupting at irq 9
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3: Intel 82801GB/GR USB UHCI Controller
(rev. 0x01)
uhci3: interrupting at irq 5
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: Intel 82801GB/GR USB EHCI Controller
(rev. 0x01)
ehci0: interrupting at irq 10
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb5 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0xe1)
pci6 at ppb5 bus 3
pci6: i/o space, memory space enabled
cbb0 at pci6 dev 1 function 0: O2 Micro product 0x7135 (rev. 0x21)
cbb0: using ioapic for interrupt
fwohci0 at pci6 dev 1 function 4: O2 Micro product 0x00f7 (rev. 0x02)
fwohci0: interrupting at irq 11
fwohci0: OHCI version 1.10 (ROM=3D0)
fwohci0: No. of Isochronous channels is 8.
fwohci0: EUI64 34:4f:c0:00:2c:28:1c:50
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
cbb0: bad Vcc request. sock_ctrl 0xa141100, sock_status 0xb010a01
cbb0: disabling socket
new status 0xb010801
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 4
pcmcia0 at cardslot0
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801GBM LPC Interface Bridge (rev. 0x01)
pciide0 at pci0 dev 31 function 2
pciide0: Intel product 0x27c4 (rev. 0x01)
pciide0: bus-master DMA support present, but unused (no driver support)
pciide0: primary channel wired to compatibility mode
pciide0: primary channel interrupting at irq 14
atabus0 at pciide0 channel 0
pciide0: secondary channel wired to compatibility mode
pciide0: secondary channel interrupting at irq 15
atabus1 at pciide0 channel 1
Intel 82801GB/GR SMBus Controller (SMBus serial bus, revision 0x01) at
pci0 dev 31 function 3 not configured
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: using exception 16
pcppi0: attached to attimer0
isapnp0: no ISA Plug 'n Play devices found
fwohci0: node_id=3D0xc800ffc0, gen=3D1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <=3D 0, cable IRM =3D 0 (me)
ieee1394if0: bus manager 0 (me)
azalia0: codec: 0x8384/0x7690 (rev. 34.1)
azalia0: codec: High Definition Audio rev. 1.0
azalia0: playback: encodings=3D1<PCM>
azalia0: playback: PCM
formats=3De07e0<24bit,20bit,16bit,192kHz,176.4kHz,96kHz,88.2kHz,48kHz,44.1k=
Hz>
azalia0: playback: max channels=3D2
azalia0: recording: encodings=3D1<PCM>
azalia0: recording: PCM
formats=3De07e0<24bit,20bit,16bit,192kHz,176.4kHz,96kHz,88.2kHz,48kHz,44.1k=
Hz>
azalia0: recording: max channels=3D2
azalia0: codec: 0x14f1/0x2bfa (rev. 0.0)
azalia0: codec: High Definition Audio rev. 0.9
azalia0: codec[1]: No audio functions
audio0 at azalia0: full duplex, independent
Kernelized RAIDframe activated
uhub5 at uhub0 port 2
uhub5: Dell product 0xa005, class 9/0, rev 2.00/50.18, addr 2
uhub5: 4 ports with 1 removable, self powered
umass0 at uhub4 port 5 configuration 1 interface 0
umass0: SanDisk Corp. Cruzer Micro, rev 2.00/20.33, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <SanDisk, Cruzer Micro, 2033> disk
removable
sd0: fabricating a geometry
sd0: 500 MB, 500 cyl, 64 head, 32 sec, 512 bytes/sect x 1024000 sectors
uhub6 at uhub1 port 1
uhub6: vendor 0x0b97 product 0x7761, class 9/0, rev 1.10/1.10, addr 2
uhub6: 3 ports with 2 removable, bus powered
wd0 at atabus0 drive 0: <ST9100824AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 95396 MB, 193821 cyl, 16 head, 63 sec, 512 bytes/sect x 195371568
sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <TSSTcorp DVD+/-RW TS-L532B, , DE03> cdrom
removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
sd0(umass0:0:0:0): no door lock
sd0: fabricating a geometry
sd0: fabricating a geometry
findroot: unable to read block 41158531
sd0: fabricating a geometry
sd0: fabricating a geometry
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
ugen0 at uhub5 port 3
ugen0: Dell TrueMobile 350 Bluetooth USB Adapter, rev 2.00/24.22, addr 3
ugen1 at uhub6 port 2
ugen1: O2 O2Micro CCID SC Reader, rev 1.10/1.10, addr 3
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)


--=20
/P=E5llen - http://www.astrakan.hig.se/~pollen
          telnet://mumindalen.astrakan.hig.se