--nextPart1160982.eQYJpe5MNB
Content-Type: multipart/mixed;
  boundary="Boundary-01=_G4QAE0EN0mdtx3o"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

--Boundary-01=_G4QAE0EN0mdtx3o
Content-Type: text/plain;
  charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
Content-Disposition: inline

On Saturday 25 February 2006 05:48, Manuel Bouyer wrote:
> On Sat, Feb 25, 2006 at 05:13:30AM +1030, Berndt Josef Wulf wrote:
> > This is not a problme. My custom kernel boots fine with fwohci enabled.=
 I
> > have attached the dmesg.log of the system in question.
>
> fwohci0: interrupting at irq 9
> fwohci0: OHCI version 1.10 (ROM=3D0)
> fwohci0: No. of Isochronous channels is 4.
> fwohci0: EUI64 42:4f:c0:00:1d:4a:34:38
> fwohci0: Phy 1394a available S400, 2 ports.
> fwohci0: Link S400, max_rec 2048 bytes.
> ieee1394if0 at fwohci0: IEEE1394 bus
> fwip0 at ieee1394if0: IP over IEEE1394
> fwohci0: Initiate bus reset
>
> At which point does it hang here with the Xen0 kernel ? With Xen0, does
> it detect fwohci0 at IRQ 9 too ? What about other devices which are
> at IRQ 9 here ?

This is what I get when booting XEN0 + fw support (hand edited):

fwohci0: interrupting at irq 9, event channel 6
fwohci0: OHCI version 1.10 (ROM=3D0)
fwohci0: No. of isochronous channels is 4
uvm_fault (0xc08d8420,0xbff16000,0,2) -> 0xe
kernel: supervisor type pagefault, code=3D0
stoppped in pid 0.1 (swapper) at netbsd: bus_dmamem_map + 0x177: movl %eax,=
=20
0xbfe00000 (%edx)


A trace in the kernel debugger reveals the following abriviated sequence:

_bus_dmamem_map()
fwdma_malloc()
fwohci_init()
fwohci_pci_attach() <- not sure if I copied my handwriting correctly!
pci_probe_device()

I've also attached the XEN0 dmesg.log with fw support disabled

Let me know if you need any other info or tests done.

cheerio Berndt

--Boundary-01=_G4QAE0EN0mdtx3o
Content-Type: text/x-log;
  charset="iso-8859-1";
  name="dmesg.log"
Content-Transfer-Encoding: quoted-printable
Content-Disposition: attachment;
	filename="dmesg.log"

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2=
006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 3.99.15 (XEN0) #0: Fri Feb 24 11:52:51 CST 2006
	wulf@barossa:/sys/arch/i386/compile/XEN0
total memory =3D 56788 KB
avail memory =3D 55612 KB
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium M (Dothan) (686-class), 1995.18 MHz, id 0x6d8
cpu0: features afe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features afe9fbff<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu0: features afe9fbff<FXSR,SSE,SSE2,SS,TM,SBF>
hypervisor0 at mainbus0
debug virtual interrupt using event channel 1
misdirect virtual interrupt using event channel 0
Domain controller: using event channel 2
xencons0 at hypervisor0: Xen Virtual Console Driver
npx0 at hypervisor0: using exception 16
PCI_PROBE_ROOT_BUSES: 0xb 0x0 0x0 0x0 0x0 0x0 0x0 0x0=20
pci0 at hypervisor0 bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82915PM/GM/GMS,82910GML Host Bridge (rev. 0x03)
agp0 at pchb0: can't find internal VGA device config space
ppb0 at pci0 dev 1 function 0: Intel 82915PM/GM PCI Express Bridge (rev. 0x=
03)
pci at ppb0 bus 1 not configured
uhci0 at pci0 dev 29 function 0: Intel 82801FB/FR USB UHCI Controller (rev.=
 0x03)
uhci0: interrupting at irq 11, event channel 4
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801FB/FR USB UHCI Controller (rev.=
 0x03)
uhci1: interrupting at irq 10, event channel 5
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801FB/FR USB UHCI Controller (rev.=
 0x03)
uhci2: interrupting at irq 9, event channel 6
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3: Intel 82801FB/FR USB UHCI Controller (rev.=
 0x03)
uhci3: interrupting at irq 7, event channel 7
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: Intel 82801FB/FR USB EHCI Controller (rev.=
 0x03)
ehci0: interrupting at irq 11, event channel 4
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb1 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0xd3)
pci at ppb1 bus 3 not configured
auich0 at pci0 dev 30 function 2: i82801FB (ICH6) AC-97 Audio
auich0: interrupting at irq 11, event channel 4
auich0: The 2nd codec is ready.
auich0: ac97: SigmaTel STAC9750/51 codec; headphone, 20 bit DAC, 20 bit ADC=
, SigmaTel 3D
auich0: ac97: ext id 605<AC97_22,AMAP,SPDIF,VRA>
Intel 82801FB/FR AC'97 Modem Controller (modem communications, revision 0x0=
3) at pci0 dev 30 function 3 not configured
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801FBM ICH6M LPC Interface Bridge (rev. 0x03)
piixide0 at pci0 dev 31 function 2
piixide0: Intel 82801FBM Serial ATA Controller (ICH6) (rev. 0x03)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel using event channel 8 for irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel using event channel 9 for irq 15
atabus1 at piixide0 channel 1
Intel 82801FB/FR SMBus Controller (SMBus serial bus, revision 0x03) at pci0=
 dev 31 function 3 not configured
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci1 at hypervisor0 bus 1
pci1: i/o space, memory space enabled
vga0 at pci1 dev 0 function 0: ATI Technologies product 0x5460 (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
wsdisplay0: screen 1-3 added (80x25, vt100 emulation)
pci2 at hypervisor0 bus 3
pci2: i/o space, memory space enabled
bce0 at pci2 dev 0 function 0: Broadcom BCM4401-B0 10/100 Ethernet
bce0: interrupting at irq 9, event channel 6
bmtphy0 at bce0 phy 1: BCM4401 10/100 media interface, rev. 0
bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bce0: Ethernet address 00:12:3f:cf:ce:1e
Ricoh 5C476 PCI-CardBus bridge (CardBus bridge, revision 0xb3) at pci2 dev =
1 function 0 not configured
Ricoh 5C552 PCI-CardBus bridge/Firewire (Firewire serial bus, interface 0x1=
0, revision 0x08) at pci2 dev 1 function 1 not configured
Ricoh product 0x0822 (system subclass 0x05, interface 0x01, revision 0x17) =
at pci2 dev 1 function 2 not configured
ath0 at pci2 dev 3 function 0
ath0: interrupting at irq 10, event channel 5
ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: mac 4.2 phy 3.0 5ghz radio 1.7 2ghz radio 2.3
ath0: Use hw queue 0 for WME_AC_BE traffic
ath0: Use hw queue 0 for WME_AC_BK traffic
ath0: Use hw queue 0 for WME_AC_VI traffic
ath0: Use hw queue 0 for WME_AC_VO traffic
ath0: Use hw queue 8 for CAB traffic
ath0: Use hw queue 9 for beacons
Xen clock: using event channel 12
auich0: measured ac97 link rate at 48892 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
crypto: assign driver 0, flags 2
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
raidattach: Asked for 8 units
Kernelized RAIDframe activated
ehci0: handing over full speed device on port 8 to uhci3
uhub4: port 8, device disappeared after reset
umct0 at uhub3 port 2
umct0: USB-RS232 Interface Converter USB Ver1.2 Device, rev 1.10/1.03, addr=
 2
ucom0 at umct0
wd0 at atabus0 drive 0: <HTS548080M9AT00>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sect=
ors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DM=
A)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <_NEC DVD+/-RW ND-6500A, , 202C> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
Searching for RAID components...
boot device: wd0
root on wd0a dumps on wd0b
mountroot: trying lfs...
mountroot: trying ffs...
root file system type: ffs
init: copying out path `/sbin/init' 11
wsdisplay0: screen 4 added (80x25, vt100 emulation)
ath0: link state changed to UP

--Boundary-01=_G4QAE0EN0mdtx3o--

--nextPart1160982.eQYJpe5MNB
Content-Type: application/pgp-signature

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2 (NetBSD)

iD8DBQBEAQ4KcUIHpeIRpjERAm+dAJ4knmHbR5K8jnK25LQrFJa3lGoY+ACfbkWe
VMcKQttgGEX4QUyRhuq+JEQ=
=fdcq
-----END PGP SIGNATURE-----

--nextPart1160982.eQYJpe5MNB--