Kevin Sullivan wrote:

> I recently bought a Sony Clie PEG-N710C.  It's a color PalmOS PDA; very
> nice little box.  Like the Visors, it hotsyncs over USB.  I'm assuming
> that the uvisor driver should be close to correct for the Clie, though I'm
> realy not sure.
>
> There's two ways to use the Clie over USB.  First, when I try to hotsync
> with the PDA plugged into my (NetBSD/i386 1.5.1) laptop, I get:
>
> usbd_new_device bus=0xc0824000 port=1 depth=1 lowspeed=0
> usbd_new_device: adding unit addr=2, rev=110, class=255, subclass=0,
> protocol=0, maxpacket=16, len=18, ls=0
> usbd_new_device: new dev (addr 2), dev=0xc0833180, parent=0xc07fdb40
> usbd_probe_and_attach: trying device specific drivers
> usbd_probe_and_attach: no device specific driver found
> usbd_probe_and_attach: looping over 1 configurations
> usbd_set_config_index: status=0x0001, error=NORMAL_COMPLETION
> usbd_set_config_index: (addr 2) attr=0xc0, selfpowered=1, power=0
> usbd_set_config_index: set config 1
> usbd_probe_and_attach: no interface drivers found
> ugen0 at uhub0 port 1
> ugen0: Sony Sony PEG COM, rev 1.10/1.00, addr 2
> usbd_set_config_index: free old config
> usbd_set_config_index: status=0x0001, error=NORMAL_COMPLETION
> usbd_set_config_index: (addr 2) attr=0xc0, selfpowered=1, power=0
> usbd_set_config_index: set config 1
>
> I can't figure out how the USB vendor and device IDs work.  Does this look
> like the uvisor driver might work, and how might I convince the uvisor
> driver to match this device?

It's impossible to say if the uvisor might work.  You could install the usbutils
package and run usbctl or usbgen to dump the device descriptors.  That might
give me a clue.



>
>
> Also, the Clie can act as a memorystick adapter; under Windows the memory
> stick shows up as another disk drive.  When I try this on NetBSD, I get:
>
> usbd_new_device bus=0xc0824000 port=1 depth=1 lowspeed=0
> usbd_new_device: adding unit addr=2, rev=110, class=0, subclass=0,
> protocol=0, maxpacket=16, len=18, ls=0
> usbd_new_device: new dev (addr 2), dev=0xc09be500, parent=0xc07fdb40
> usbd_probe_and_attach: trying device specific drivers
> usbd_probe_and_attach: no device specific driver found
> usbd_probe_and_attach: looping over 1 configurations
> usbd_set_config_index: status=0x0001, error=NORMAL_COMPLETION
> usbd_set_config_index: (addr 2) attr=0xc0, selfpowered=1, power=6
> usbd_set_config_index: set config 1
> umass0 at uhub0 port 1 configuration 1 interface 0
> umass0: Sony Sony PEG Mass Storage, rev 1.10/1.00, addr 2
> umass0: using SFF8070i over CBI-I
> atapibus0 at umass0 channel 0
>
> So it finds the atapibus but not the memory stick.  Any suggestions?

I'm not sure why you don't get a disk attached.

    -- Lennart