Re: Serial port using hpcmips

[ehafener <ehafener%gmail.com@localhost>]

Here is the dmesg output:

NEC MobilePro 770 (NEC VR4121 rev0.0 131.072MHz)
total memory = 32768 KB
avail memory = 27852 KB
timecounter: Timecounters tick every 10.000 msec
mainbus0 (root)
cpu0 at mainbus0: NEC VR4100 CPU (0xc60) Rev. 6.0 with software
emulated floating point
cpu0: 16KB/16B direct-mapped L1 Instruction cache, 32 TLB entries
cpu0: 8KB/16B direct-mapped write-back L1 Data cache
vr4102ip0 at mainbus0
vrbcu0 at vr4102ip0 addr 0x0b000000-001f
vrbcu0: CPU 131.072MHz, bus 32.768MHz, ram 65.536MHz
vrcmu0 at vr4102ip0 addr 0x0b000060-007f
vrgiu0 at vr4102ip0 addr 0x0b000100-011f
vrdmaau0 at vr4102ip0 addr 0x0b000020-0037
vrdcu0 at vr4102ip0 addr 0x0b000040-004b
vrrtc0 at vr4102ip0 addr 0x0b0000c0-00df
vrkiu0 at vr4102ip0 addr 0x0b000180-019f
hpckbd0 at vrkiu0
wskbd0 at hpckbd0: console keyboard
vrpmu0 at vr4102ip0 addr 0x0b0000a0-00bf
vrpmu: Deadman's switch detected
vrdsu0 at vr4102ip0 addr 0x0b0000e0-00e7
vrled0 at vr4102ip0 addr 0x0b000240-024f
vrpiu0 at vr4102ip0 addr 0x0b000120-013f, 0x0b0002a0-02bf
wsmouse0 at vrpiu0 mux 0
vrpiu0: WARNING: powerhook_establish is deprecated
vrc4172pwm0 at vr4102ip0 addr 0x15003880-3885
vraiu0 at vr4102ip0 addr 0x0b000160-017f
audio0 at vraiu0: half duplex
vrisab0 at vrgiu0: ISA port 0x14000000-0x18000000 mem 0x10000000-0x14000000
isa0 at vrisab0
pcic0 at isa0 port 0x3e0-0x3e1 iomem 0x70000-0x73fff irq 589827
pcic0: controller 0 (Ricoh RF5C396) has sockets A and B
pcmcia0 at pcic0 controller 0 socket 0
pcmcia1 at pcic0 controller 0 socket 1
bivideo0 at mainbus0: pseudo video controller, console
bivideo0: framebuffer address: 0xaa000000
bivideo0: WARNING: powerhook_establish is deprecated
hpcfb0 at bivideo0: 640x240 pixels, 65536 colors, 80x24 chars
hpcfb0: WARNING: powerhook_establish is deprecated
wsdisplay0 at hpcfb0 kbdmux 1: console (std, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
btnmgr0 at mainbus0
wskbd1 at btnmgr0 mux 1
wskbd1: connecting to wsdisplay0
hpcapm0 at mainbus0: pseudo power management module
apmdev0 at hpcapm0: Power Management spec V1.2
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "vrrtc" frequency 32768 Hz quality 100
pcic0: using irq 589827 for socket events
wdc1 at pcmcia0 function 0: <SanDisk, SDP, 5/3 0.6>
pcic0: port 0x14000400-0x1400040f
wdc1: i/o mapped mode
pcmcia0: card irq 3
atabus0 at wdc1 channel 0
wd0 at atabus0 drive 0: <SanDisk SDCFH-002G>
wd0: drive supports 1-sector PIO transfers, LBA addressing
wd0: 1907 MB, 3875 cyl, 16 head, 63 sec, 512 bytes/sect x 3906560 sectors
wd0: drive supports PIO mode 4
ne0 at pcmcia1 function 0: <Network Everywhere, Ethernet 10BaseT PC
Card, 2.0,  >
pcic0: port 0x14000420-0x1400043f
pcmcia1: card irq 3
boot device: wd0
root on wd0a dumps on wd0b
pcmcia0: card irq 3
pcmcia0: card irq 3
root file system type: ffs

I'm using the standard generic kernel.

Thanks!



On 9/6/11, Andy Ruhl <acruhl%gmail.com@localhost> wrote:
> On Tue, Sep 6, 2011 at 11:21 AM, ehafener <ehafener%gmail.com@localhost> 
> wrote:
>> I have a mobilepro 770 which has a functioning serial port (at least
>> it works in Windows CE).  I have NetBSD 5.0.2 hpcmips installed on it.
>>  I am interested in using the serial port to control relays on a robot
>> but can't seem to get the serial port configured.
>>
>> I looked it /etc/ttys and noticed this file is abbreviated in hpcmips
>> when compared to i386.
>>
>> I ran dmesg and didn't see anything that looked like the serial port.
>>
>> Any help would be greatly appreciated.
>
> You should post the dmesg. If you built a custom kernel, you should
> post the config for it as well.
>
> You might need to uncomment something related to serial ports and
> build a kernel to get the serial port.
>
> Andy
>