Port-hp300 archive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]

Free to a good home: 9000/362



I've decided to part with my dear old HP 9000/362.  I dusted it off, installed 
-current, and am willing to ship it anywhere in the US.  It comes with an HIL 
keyboard (no mouse) and ethernet.  It's got 16 MB RAM, a 1 GB SCSI disk, and an 
integrated 640x480 VGA gendiofb.   See below for full dmesg.  I got X to start 
with a blank screen, but couldn't get much further without a mouse.

While installing, I noticed a few things that probably should be fixed.

I couldn't install with the standard utilities.  When I got to the first screen 
("Shall we continue"), it hung with:
sd0(spc0:0:0:0): illegal request, data = 00 00 00 00 20 00 00 00               
sd1(spc0:0:2:0): timed out

I tried "upgrading" instead of "installing", and it didn't help.  I tried 
unplugging the SCSI floppy, but that also didn't help:
sd0(spc0:0:2:0): timed out

The RAMDISK installer utils don't use DHCP, you have to manually enter IP 
information.

Otherwise, it's really impressive that this > 20 year old hardware works with 
an up-to-date OS.

So if you want this gem of a relic, let me know!

  -- MW



>> NetBSD/hp300 Primary Boot, Revision 1.18 (from NetBSD 5.99.53)
>> HP 9000/362 SPU
>> Enter "reset" to reset system.
Boot: [[[le0a:]netbsd][-a][-c][-d][-s][-v][-q]] :- sd2a:netbsd
2969228+139772 [353872+228296]=0x3856c0
Start @ 0xff003400 [1=0xff2f9088-0x3856c0]...
Entry point: 0xff003400
bootinfo found at 0xff002000
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.53 (GENERIC) #0: Mon Jun 27 13:29:24 UTC 2011
        
builds%b7.netbsd.org@localhost:/home/builds/ab/HEAD/hp300/201106270850Z-obj/home/builds/ab/HEAD/src/sys/arch/hp300/compile/GENERIC
HP 9000/362 (25MHz MC68030 CPU+MMU, 25MHz MC68882 FPU)
total memory = 16372 KB
avail memory = 11340 KB
mainbus0 (root)
intio0 at mainbus0
rtc0 at intio0 addr 0x420000
hil0 at intio0 addr 0x428000 ipl 1
nhpib1 at intio0 addr 0x478000 ipl 3: internal HP-IB
hpibbus1 at nhpib1
dma0 at intio0 addr 0x500000 ipl 1: 98620C, 2 channels, 32-bit DMA
dio0 at mainbus0
com0 at dio0 scode 9 ipl 5: ns16550a, working fifo
com0: console
internal parallel at dio0 scode 12 ipl 3 not configured
spc0 at dio0 scode 14 ipl 4: 98265A SCSI, 32-bit DMA, SCSI ID 7
scsibus0 at spc0: 8 targets, 8 luns per target
le0 at dio0 scode 21 ipl 5: address 08:00:09:10:d8:c2
le0: 8 receive buffers, 2 transmit buffers
gendiofb0 at dio0 scode 132 ipl 3: 640x480x8 frame buffer
wsdisplay0 at gendiofb0 kbdmux 1
scsibus0: waiting 2 seconds for devices to settle...
hilkbd0 at hil0 code 1: 109-key keyboard, layout 1f
wskbd0 at hilkbd0 mux 1
sd0 at scsibus0 target 0 lun 0: <TEAC, FC-1     HF   07, RV A> disk removable
sd0(spc0:0:0:0): not ready, data = 00 00 00 00 04 00 00 00
sd0: drive offline
sd0: async, 8-bit transfers
sd1 at scsibus0 target 2 lun 0: <SEAGATE, ST31230N, 0300> disk fixed
sd1: 1010 MB, 3992 cyl, 5 head, 103 sec, 512 bytes/sect x 2069860 sectors
sd1: async, 8-bit transfers
sd0(spc0:0:0:0): not ready, data = 00 00 00 00 04 00 00 00
sd0(spc0:0:0:0): illegal request, data = 00 00 00 00 20 00 00 00
boot device: sd1
root on sd1a dumps on sd1b
root file system type: ffs
/etc/rc.conf is not configured.  Multiuser boot aborted.
Enter pathname of shell or RETURN for /bin/sh: 


[...]

 You have chosen to install NetBSD on your hard disk.  This will change
 information on your hard disk.  You should have made a full backup before
 this procedure!  This procedure will do the following things:
         a) Partition your disk
         b) Create new BSD file systems
         c) Load and install distribution sets
         d) Some initial system configuration
 
 (After you enter the partition information but before your disk is changed,
 you will have the opportunity to quit this procedure.)
 
 Shall we continue?

sd0(spc0:0:0:0): illegal request, data = 00 00 00 00 20 00 00 00               
sd1(spc0:0:2:0): timed out


[...]

# disklabel sd1
# /dev/rsd1c:
type: SCSI
disk: ST31230N
label: 
flags:
bytes/sector: 512
sectors/track: 103
tracks/cylinder: 5
sectors/cylinder: 515
cylinders: 3993
total sectors: 2069860
rpm: 3600
interleave: 1
trackskew: 0
cylinderskew: 0
headswitch: 0           # microseconds
track-to-track seek: 0  # microseconds
drivedata: 0 

8 partitions:
#        size    offset     fstype  [fsize bsize cpg/sgs]
 a:   1969660       200     4.2BSD   1024  8192     0   # (Cyl.    0*- 3824*)
 b:    100000   1969860       swap                      # (Cyl. 3824*- 4019*)
 c:   2069860         0       boot                      # (Cyl.    0 - 4019*)


Home | Main Index | Thread Index | Old Index