5.0 on hp382

[Izumi Tsutsui <tsutsui%ceres.dti.ne.jp@localhost>]

I receive a question about 375 and 380, but I only have 382 and 425t.

040 models should also work, but there have been very few reports
about 020/030 models for long years so there might be some botches
on those machines.

Note the GENERIC kernel may require at least 8MB memory
because GENERIC itself is ~3.3MB. For 4MB machines
you might have to build a custom shrinked kernel.

Any tests/reports are appreciated :-)

---
 Self-Test Mode
Copyright 1991,
Hewlett-Packard Company.
All Rights Reserved.

BOOTROM  Rev. 3.01  2 MAY 91
MC68040 Processor
Configuration EEPROM
Utility Chip at 41
HP-HIL
 RESET To Restart
 Self-Test Mode
HP-IB
DMA-C0
 Self-Test Mode
RAM 25165482 Bytes
HP98624 (HP-IB) at 8
HP98644 (RS-232) at 9
HP PARALLEL at 12
HP98265 (SCSI S 32) at 14
HP98643 (LAN) at 21, AUI, 08000918D8D2
Bit Mapped Video at 132 (Console)
 Booting System


>> NetBSD/hp300 Primary Boot, Revision 1.16 (from NetBSD 5.0)
>> HP 9000/382 SPU
>> Enter "reset" to reset system.
Boot: [[[sd0a:]netbsd][-a][-c][-d][-s][-v][-q]] :- 
2647924+63760+340356 [333440+209732]=0x36ff04
Start @ 0xfe803400 [1=0xfeaed214-0x36ff04]...
Entry point: 0xfe803400
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.0 (GENERIC) #0: Sun Apr 26 16:25:34 UTC 2009
        
builds%b0.netbsd.org@localhost:/home/builds/ab/netbsd-5-0-RELEASE/hp300/200904260229Z-obj/home/builds/ab/netbsd-5-0-RELEASE/src/sys/arch/hp300/compile/GENERIC
HP 9000/382 (25MHz MC68040 CPU+MMU+FPU, 4k on-chip physical I/D caches)
total memory = 24564 KB
avail memory = 19440 KB
mainbus0 (root)
intio0 at mainbus0
rtc0 at intio0 addr 0x420000
frodo0 at intio0 addr 0x41c000 ipl 5
dnkbd at frodo0 offset 0x0 not configured
com1 at frodo0 offset 0x40: ns8250 or ns16450, no fifo
com2 at frodo0 offset 0x60: ns8250 or ns16450, no fifo
hil0 at intio0 addr 0x428000 ipl 1
nhpib1 at intio0 addr 0x478000 ipl 3: internal HP-IB
hpibbus1 at nhpib1
dma0 at intio0 addr 0x500000 ipl 1: 98620C, 2 channels, 32-bit DMA
dio0 at mainbus0
nhpib2 at dio0 scode 8 ipl 3: 98624A HP-IB
hpibbus2 at nhpib2
com0 at dio0 scode 9 ipl 5: ns16550a, working fifo
com0: console
internal parallel at dio0 scode 12 ipl 3 not configured
spc0 at dio0 scode 14 ipl 4: 98265A SCSI, 32-bit DMA, SCSI ID 7
scsibus0 at spc0: 8 targets, 8 luns per target
le0 at dio0 scode 21 ipl 5: address 08:00:09:18:d8:d2
le0: 8 receive buffers, 2 transmit buffers
WARNING: select code size unknown for id = 0x39 secid = 0x10
device id = 0x39 secid = 0x10 at dio0 scode 132 ipl 3 not configured
WARNING: select code size unknown for id = 0x39 secid = 0x10
device id = 0x39 secid = 0x10 at dio0 scode 133 ipl 3 not configured
nhpib3 at dio0 scode 134 ipl 3: 98624A HP-IB
hpibbus3 at nhpib3
nhpib4 at dio0 scode 135 ipl 3: 98624A HP-IB
hpibbus4 at nhpib4
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <FUJITSU, M2952S-512, 0147> disk fixed
sd0: 2291 MB, 5714 cyl, 5 head, 164 sec, 512 bytes/sect x 4693462 sectors
sd0: async, 8-bit transfers
sd1 at scsibus0 target 1 lun 0: <TEAC, FC-1     HF   07, RV A> disk removable
sd1(spc0:0:1:0): not ready, data = 00 00 00 00 04 00 00 00
sd1: drive offline
sd1: async, 8-bit transfers
Kernelized RAIDframe activated
sd1(spc0:0:1:0): not ready, data = 00 00 00 00 04 00 00 00
sd1(spc0:0:1:0): illegal request, data = 00 00 00 00 20 00 00 00
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
Thu Apr 30 04:19:57 GMT 2009
swapctl: adding /dev/sd0b as swap device at priority 0
Starting file system checks:
/dev/rsd0a: file system is clean; not checking
/dev/rsd0f: file system is clean; not checking
/dev/rsd0g: file system is clean; not checking
Setting tty flags.

 :

---
Izumi Tsutsui