You probably have bad hardware. Ethernet errors should not happen. That 
would be my first guess. It looks like you have qube 1 (2700?). Wasn't 
there some sort of ethernet problem with that unit and netbsd?


Thanks,
Alex


Marcel wrote:
> It doesn't work for me... : (    Attached output is the installation and the
> first boot, I've noticed some errors on the tlp0 during copying.
> Any clue what would be the problem here?
> 
> Marcel
> 
> 
> 
> 
> [Console]
> ���Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002
> 
> The NetBSD Foundation, Inc. All rights reserved.
> 
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> 
> The Regents of the University of California. All rights reserved.
> 
> 
> 
> NetBSD 1.6.1 (INSTALL.LCD) #0: Thu Jun 26 22:29:11 CEST 2003
> 
> cdi@merlin.camelot.net:/misc/home/cdi/src/netbsd/1.6.1/src/sys/arch/cobalt/c
> ompile/INSTALL.LCD
> 
> 256 MB memory, 234 MB free, 13208 KB in 3302 buffers
> 
> mainbus0 (root)
> 
> com0 at mainbus0 addr 0x1c800000 level 3: st16650a, working fifo
> 
> com0: console
> 
> cpu0 at mainbus0: QED RM5200 CPU (0x28a0) Rev. 10.0 with built-in FPU Rev.
> 10.0
> 
> cpu0: 32KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries
> 
> cpu0: 32KB/32B 2-way set-associative write-back L1 Data cache
> 
> gt0 at mainbus0 addr 0x14000000
> 
> pci0 at gt0
> 
> pci0: i/o space, memory space enabled, rd/line, wr/inv ok
> 
> pchb0 at pci0 dev 0 function 0: Galileo GT-64111 System Controller, rev 1
> 
> tlp0 at pci0 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1
> 
> tlp0: interrupting at level 1
> 
> tlp0: Ethernet address 00:10:e0:00:5f:6e
> 
> lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3
> 
> lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> 
> Symbios Logic 53c860 (SCSI mass storage, revision 0x02) at pci0 dev 8
> function 0 not configured
> 
> pcib0 at pci0 dev 9 function 0
> 
> pcib0: VIA Technologies VT82C586 (Apollo VP) PCI-ISA Bridge, rev 37
> 
> pciide0 at pci0 dev 9 function 1: VIA Technologies VT82C586 (Apollo VP)
> ATA33 controller
> 
> pciide0: bus-master DMA support present
> 
> pciide0: primary channel configured to compatibility mode
> 
> wd0 at pciide0 channel 0 drive 0: <Maxtor 6E040L0>
> 
> wd0: drive supports 16-sector PIO transfers, LBA addressing
> 
> wd0: 39205 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 80293248 sectors
> 
> wd0: 32-bit data port
> 
> wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
> 
> pciide0: primary channel interrupting at irq 14
> 
> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA
> data transfers)
> 
> pciide0: secondary channel configured to compatibility mode
> 
> pciide0: disabling secondary channel (no drives)
> 
> VIA Technologies VT83C572 USB Controller (USB serial bus, revision 0x02) at
> pci0 dev 9 function 2 not configured
> 
> tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1
> 
> tlp1: interrupting at level 2
> 
> tlp1: Ethernet address 00:10:e0:00:5f:6f
> 
> lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3
> 
> lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> 
> lcd0 at mainbus0
> 
> boot device: <unknown>
> 
> root on tlp0
> 
> nfs_boot: trying DHCP/BOOTP
> 
> nfs_boot: DHCP next-server: 10.0.0.254
> 
> nfs_boot: my_domain=mfg.cobaltmicro.com
> 
> nfs_boot: my_addr=10.0.0.160
> 
> nfs_boot: my_mask=255.0.0.0
> 
> root on 10.0.0.254:/nfsroot
> 
> warning: no /dev/console
> 
> init: Creating mfs /dev
> 
> Wed Mar 9 22:06:51 GMT 2005
> 
> Starting file system checks:
> 
> Coming up: fixing /dev...
> 
> Coming up: fixing /var...
> 
> Preparing the installation...
> 
> Setting tty flags.
> 
> Setting sysctl variables:
> 
> Starting network.
> 
> Hostname: client
> 
> Configuring network interfaces:.
> 
> Building databases...
> 
> kvm_mkdb: machdep.booted_kernel: the value is not available: No such file or
> directory
> 
> Mounting all filesystems...
> 
> Checking quotas: done.
> 
> Setting securelevel: kern.securelevel: 0 -> 1
> 
> /etc/rc: WARNING: No swap space configured!
> 
> starting local daemons:tlp0: receive error: MII error
> 
> tlp0: receive error: CRC error
> 
> Trace/BPT trap
> 
> ------------------------------------------------
> 
> Setting up the disk...
> 
> ------------------------------------------------
> 
> mknod: /dev/lcd: File exists
> 
> ------------------------------------------------
> 
> Clearing partition information...
> 
> ------------------------------------------------
> 
> Trace/BPT trap
> 
> Trace/BPT trap
> 
> Trace/BPT trap
> 
> Trace/BPT trap
> 
> ------------------------------------------------
> 
> Setting up the Ext2 partition...
> 
> ------------------------------------------------
> 
> expr: non-integer argument '*'
> 
> [: -gt: argument expected
> 
> [: 0: unexpected operator
> 
> fdisk: Bad argument to the -s flag.
> 
> : Undefined error: 0
> 
> expr: syntax error
> 
> [: -: bad number
> 
> expr: syntax error
> 
> ------------------------------------------------
> 
> Setting up swap...
> 
> ------------------------------------------------
> 
> expr: non-integer argument '*'
> 
> [: -gt: argument expected
> 
> [: 0: unexpected operator
> 
> fdisk: Bad argument to the -s flag.
> 
> : Undefined error: 0
> 
> expr: syntax error
> 
> [: 0: unexpected operator
> 
> ------------------------------------------------
> 
> Setting up BSD partition...
> 
> ------------------------------------------------
> 
> fdisk: Bad argument to the -s flag.
> 
> : Undefined error: 0
> 
> expr: non-integer argument '*'
> 
> [: -gt: argument expected
> 
> [: 0: unexpected operator
> 
> expr: syntax error
> 
> expr: non-integer argument '*'
> 
> [: -gt: argument expected
> 
> [: 0: unexpected operator
> 
> expr: non-integer argument '*'
> 
> expr: non-integer argument '*'
> 
> [: 0: unexpected operator
> 
> expr: syntax error
> 
> [: -: bad number
> 
> expr: syntax error
> 
> expr: non-integer argument '*'
> 
> [: -gt: argument expected
> 
> [: 0: unexpected operator
> 
> expr: non-integer argument '*'
> 
> expr: non-integer argument '*'
> 
> [: 0: unexpected operator
> 
> expr: syntax error
> 
> [: 0: unexpected operator
> 
> disklabel: line 22: invalid format
> 
> disklabel: line 22: warning, unknown filesystem type: Ext2
> 
> disklabel: line 23: invalid format
> 
> disklabel: line 23: too few fields
> 
> Segmentation fault
> 
> ------------------------------------------------
> 
> Setting up boot partition...
> 
> ------------------------------------------------
> 
> mke2fs 1.19, 13-Jul-2000 for EXT2 FS 0.5b, 95/08/09
> 
> Filesystem label=
> 
> OS type: Linux
> 
> Block size=1024 (log=0)
> 
> Fragment size=1024 (log=0)
> 
> 7712 inodes, 30743 blocks
> 
> 0 blocks (0.00%) reserved for the super user
> 
> First data block=1
> 
> 4 block groups
> 
> 8192 blocks per group, 8192 fragments per group
> 
> 1928 inodes per group
> 
> Superblock backups stored on blocks:
> 
> 8193, 16385, 24577
> 
> Writing inode tables: 0/41/42/43/4done
> 
> Writing superblocks and filesystem accounting information: done
> 
> ------------------------------------------------
> 
> Setting up /var...
> 
> ------------------------------------------------
> 
> /dev/wd0f: 4195296 sectors in 4162 cylinders of 16 tracks, 63 sectors
> 
> 2048.5MB in 13 cyl groups (330 c/g, 162.42MB/g, 19968 i/g)
> 
> super-block backups (for fsck -b #) at:
> 
> 32, 332736, 665440, 998144, 1330848, 1663552, 1996256, 2328960,
> 
> 2661664, 2994368, 3327072, 3659776, 3992480,
> 
> wtfs: write error for sector 16: Read-only file system
> 
> ------------------------------------------------
> 
> Setting up /tmp...
> 
> ------------------------------------------------
> 
> /dev/wd0g: 1024128 sectors in 1016 cylinders of 16 tracks, 63 sectors
> 
> 500.1MB in 12 cyl groups (86 c/g, 42.33MB/g, 10368 i/g)
> 
> super-block backups (for fsck -b #) at:
> 
> 32, 86784, 173536, 260288, 347040, 433792, 520544, 607296, 694048,
> 
> 780800, 867552, 954304,
> 
> ------------------------------------------------
> 
> Setting up root...
> 
> ------------------------------------------------
> 
> /dev/wd0a: 73963008 sectors in 73376 cylinders of 16 tracks, 63 sectors
> 
> 36114.8MB in 224 cyl groups (328 c/g, 161.44MB/g, 20352 i/g)
> 
> super-block backups (for fsck -b #) at:
> 
> 32, 330720, 661408, 992096, 1322784, 1653472, 1984160,
> 
> 2314848, 2645536, 2976224, 3306912, 3637600, 3968288, 4298976,
> 
> 4629664, 4960352, 5290016, 5620704, 5951392, 6282080, 6612768,
> 
> 6943456, 7274144, 7604832, 7935520, 8266208, 8596896, 8927584,
> 
> 9258272, 9588960, 9919648, 10250336, 10580000, 10910688, 11241376,
> 
> 11572064, 11902752, 12233440, 12564128, 12894816, 13225504, 13556192,
> 
> 13886880, 14217568, 14548256, 14878944, 15209632, 15540320, 15869984,
> 
> 16200672, 16531360, 16862048, 17192736, 17523424, 17854112, 18184800,
> 
> 18515488, 18846176, 19176864, 19507552, 19838240, 20168928, 20499616,
> 
> 20830304, 21159968, 21490656, 21821344, 22152032, 22482720, 22813408,
> 
> 23144096, 23474784, 23805472, 24136160, 24466848, 24797536, 25128224,
> 
> 25458912, 25789600, 26120288, 26449952, 26780640, 27111328, 27442016,
> 
> 27772704, 28103392, 28434080, 28764768, 29095456, 29426144, 29756832,
> 
> 30087520, 30418208, 30748896, 31079584, 31410272, 31739936, 32070624,
> 
> 32401312, 32732000, 33062688, 33393376, 33724064, 34054752, 34385440,
> 
> 34716128, 35046816, 35377504, 35708192, 36038880, 36369568, 36700256,
> 
> 37029920, 37360608, 37691296, 38021984, 38352672, 38683360, 39014048,
> 
> 39344736, 39675424, 40006112, 40336800, 40667488, 40998176, 41328864,
> 
> 41659552, 41990240, 42319904, 42650592, 42981280, 43311968, 43642656,
> 
> 43973344, 44304032, 44634720, 44965408, 45296096, 45626784, 45957472,
> 
> 46288160, 46618848, 46949536, 47280224, 47609888, 47940576, 48271264,
> 
> 48601952, 48932640, 49263328, 49594016, 49924704, 50255392, 50586080,
> 
> 50916768, 51247456, 51578144, 51908832, 52239520, 52570208, 52899872,
> 
> 53230560, 53561248, 53891936, 54222624, 54553312, 54884000, 55214688,
> 
> 55545376, 55876064, 56206752, 56537440, 56868128, 57198816, 57529504,
> 
> 57860192, 58189856, 58520544, 58851232, 59181920, 59512608, 59843296,
> 
> 60173984, 60504672, 60835360, 61166048, 61496736, 61827424, 62158112,
> 
> 62488800, 62819488, 63150176, 63479840, 63810528, 64141216, 64471904,
> 
> 64802592, 65133280, 65463968, 65794656, 66125344, 66456032, 66786720,
> 
> 67117408, 67448096, 67778784, 68109472, 68440160, 68769824, 69100512,
> 
> 69431200, 69761888, 70092576, 70423264, 70753952, 71084640, 71415328,
> 
> 71746016, 72076704, 72407392, 72738080, 73068768, 73399456, 73730144,
> 
> ------------------------------------------------
> 
> Setting up boot partition......
> 
> ------------------------------------------------
> 
> 
> 
> ------------------------------------------------
> 
> Copying files...
> 
> ------------------------------------------------
> 
> 
> 
> ------------------------------------------------
> 
> Unpacking base.tgz...
> 
> ------------------------------------------------
> 
> tlp0: receive error: MII error
> 
> tlp0: receive error: CRC error
> 
> tlp0: receive error: MII error
> 
> tlp0: receive error: CRC error
> 
> tlp0: receive error: CRC error
> 
> ------------------------------------------------
> 
> Unpacking comp.tgz...
> 
> ------------------------------------------------
> 
> tlp0: receive error: MII error
> 
> tlp0: receive error: CRC error
> 
> tlp0: receive error: CRC error
> 
> tlp0: receive error: MII error
> 
> tlp0: receive error: CRC error
> 
> ------------------------------------------------
> 
> Unpacking etc.tgz...
> 
> ------------------------------------------------
> 
> 
> 
> ------------------------------------------------
> 
> Unpacking man.tgz...
> 
> ------------------------------------------------
> 
> tlp0: receive error: MII error
> 
> tlp0: receive error: CRC error
> 
> ------------------------------------------------
> 
> Unpacking misc.tgz...
> 
> ------------------------------------------------
> 
> tlp0: receive error: MII error
> 
> tlp0: receive error: CRC error
> 
> ------------------------------------------------
> 
> Unpacking text.tgz...
> 
> ------------------------------------------------
> 
> tlp0: receive error: MII error
> 
> tlp0: receive error: CRC error
> 
> ------------------------------------------------
> 
> Fixing up /dev...
> 
> ------------------------------------------------
> 
> 
> 
> ------------------------------------------------
> 
> Fixing up /etc...
> 
> ------------------------------------------------
> 
> 
> 
> ------------------------------------------------
> 
> Rebooting...
> 
> ------------------------------------------------
> 
> Mar 9 22:15:01 reboot: rebooted by root syncing disks... done
> 
> rebooting...
> 
> 
> 
> ì
> 
> 
>>>NetBSD/cobalt 1.6U Bootloader, Revision 0.1 [@0x81000000]
> 
> 
>>>(cdi@merlin.camelot.net, Fri Jun 27 20:23:25 CEST 2003)
> 
> 
>>>Memory: 262144 k
> 
> 
>>>PROM boot string: root=/dev/hda1 ro
> 
> 
> Loading: wd0a:netbsd
> 
> |/-\|2500768/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-
> \|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|
> /-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-
> \|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|
> /-\|/-\|/+252384- [85488\|/-\+76831|/-\|]=0x2c7f6c
> 
> Starting at 0x80001000
> 
> invalid bootinfo (standalone boot?)
> 
> [ Kernel symbol table missing! ]
> 
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004
> 
> The NetBSD Foundation, Inc. All rights reserved.
> 
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> 
> The Regents of the University of California. All rights reserved.
> 
> 
> 
> NetBSD 2.0 (GENERIC) #0: Wed Dec 1 03:01:00 UTC 2004
> 
> builds@build:/big/builds/ab/netbsd-2-0-RELEASE/cobalt/200411300000Z-obj/big/
> builds/ab/netbsd-2-0-RELEASE/src/sys/arch/cobalt/compile/GENERIC
> 
> total memory = 256 MB
> 
> avail memory = 247 MB
> 
> mainbus0 (root)
> 
> com0 at mainbus0 addr 0x1c800000 level 3: st16650a, working fifo
> 
> com0: console
> 
> cpu0 at mainbus0: QED RM5200 CPU (0x28a0) Rev. 10.0 with built-in FPU Rev.
> 10.0
> 
> cpu0: 32KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries
> 
> cpu0: 32KB/32B 2-way set-associative write-back L1 Data cache
> 
> panel0 at mainbus0 addr 0x1f000000
> 
> gt0 at mainbus0 addr 0x14000000
> 
> pci0 at gt0
> 
> pci0: i/o space, memory space enabled, rd/line, wr/inv ok
> 
> pchb0 at pci0 dev 0 function 0: Galileo GT-64111 System Controller, rev 1
> 
> tlp0 at pci0 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1
> 
> tlp0: interrupting at level 1
> 
> tlp0: Ethernet address 00:10:e0:00:5f:6e
> 
> lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3
> 
> lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> 
> siop0 at pci0 dev 8 function 0: Symbios Logic 53c860 (ultra scsi)
> 
> siop0: interrupting at irq 4
> 
> scsibus0 at siop0: 8 targets, 8 luns per target
> 
> pcib0 at pci0 dev 9 function 0
> 
> pcib0: VIA Technologies VT82C586 (Apollo VP) PCI-ISA Bridge, rev 37
> 
> viaide0 at pci0 dev 9 function 1
> 
> viaide0: VIA Technologies VT82C586 (Apollo VP) ATA33 controller
> 
> viaide0: bus-master DMA support present
> 
> viaide0: primary channel configured to compatibility mode
> 
> viaide0: primary channel interrupting at irq 14
> 
> atabus0 at viaide0 channel 0
> 
> viaide0: secondary channel configured to compatibility mode
> 
> viaide0: secondary channel interrupting at irq 15
> 
> atabus1 at viaide0 channel 1
> 
> VIA Technologies VT83C572 USB Controller (USB serial bus, revision 0x02) at
> pci0 dev 9 function 2 not configured
> 
> tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1
> 
> tlp1: interrupting at level 2
> 
> tlp1: Ethernet address 00:10:e0:00:5f:6f
> 
> lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3
> 
> lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> 
> Kernelized RAIDframe activated
> 
> scsibus0: waiting 2 seconds for devices to settle...
> 
> wd0 at atabus0 drive 0INTRF
> 
> panic: siop_intr: I shouldn't be there !
> 
> Stopped at 0x801b5808: jr ra
> 
> bdslot: nop
> 
> db>
> 
> 
> 
> 
>