It doesn't work for me... : (    Attached output is the installation and the
first boot, I've noticed some errors on the tlp0 during copying.
Any clue what would be the problem here?

Marcel




[Console]
���Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002

The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1982, 1986, 1989, 1991, 1993

The Regents of the University of California. All rights reserved.



NetBSD 1.6.1 (INSTALL.LCD) #0: Thu Jun 26 22:29:11 CEST 2003

cdi@merlin.camelot.net:/misc/home/cdi/src/netbsd/1.6.1/src/sys/arch/cobalt/c
ompile/INSTALL.LCD

256 MB memory, 234 MB free, 13208 KB in 3302 buffers

mainbus0 (root)

com0 at mainbus0 addr 0x1c800000 level 3: st16650a, working fifo

com0: console

cpu0 at mainbus0: QED RM5200 CPU (0x28a0) Rev. 10.0 with built-in FPU Rev.
10.0

cpu0: 32KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries

cpu0: 32KB/32B 2-way set-associative write-back L1 Data cache

gt0 at mainbus0 addr 0x14000000

pci0 at gt0

pci0: i/o space, memory space enabled, rd/line, wr/inv ok

pchb0 at pci0 dev 0 function 0: Galileo GT-64111 System Controller, rev 1

tlp0 at pci0 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1

tlp0: interrupting at level 1

tlp0: Ethernet address 00:10:e0:00:5f:6e

lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3

lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto

Symbios Logic 53c860 (SCSI mass storage, revision 0x02) at pci0 dev 8
function 0 not configured

pcib0 at pci0 dev 9 function 0

pcib0: VIA Technologies VT82C586 (Apollo VP) PCI-ISA Bridge, rev 37

pciide0 at pci0 dev 9 function 1: VIA Technologies VT82C586 (Apollo VP)
ATA33 controller

pciide0: bus-master DMA support present

pciide0: primary channel configured to compatibility mode

wd0 at pciide0 channel 0 drive 0: <Maxtor 6E040L0>

wd0: drive supports 16-sector PIO transfers, LBA addressing

wd0: 39205 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 80293248 sectors

wd0: 32-bit data port

wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)

pciide0: primary channel interrupting at irq 14

wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA
data transfers)

pciide0: secondary channel configured to compatibility mode

pciide0: disabling secondary channel (no drives)

VIA Technologies VT83C572 USB Controller (USB serial bus, revision 0x02) at
pci0 dev 9 function 2 not configured

tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1

tlp1: interrupting at level 2

tlp1: Ethernet address 00:10:e0:00:5f:6f

lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3

lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto

lcd0 at mainbus0

boot device: <unknown>

root on tlp0

nfs_boot: trying DHCP/BOOTP

nfs_boot: DHCP next-server: 10.0.0.254

nfs_boot: my_domain=mfg.cobaltmicro.com

nfs_boot: my_addr=10.0.0.160

nfs_boot: my_mask=255.0.0.0

root on 10.0.0.254:/nfsroot

warning: no /dev/console

init: Creating mfs /dev

Wed Mar 9 22:06:51 GMT 2005

Starting file system checks:

Coming up: fixing /dev...

Coming up: fixing /var...

Preparing the installation...

Setting tty flags.

Setting sysctl variables:

Starting network.

Hostname: client

Configuring network interfaces:.

Building databases...

kvm_mkdb: machdep.booted_kernel: the value is not available: No such file or
directory

Mounting all filesystems...

Checking quotas: done.

Setting securelevel: kern.securelevel: 0 -> 1

/etc/rc: WARNING: No swap space configured!

starting local daemons:tlp0: receive error: MII error

tlp0: receive error: CRC error

Trace/BPT trap

------------------------------------------------

Setting up the disk...

------------------------------------------------

mknod: /dev/lcd: File exists

------------------------------------------------

Clearing partition information...

------------------------------------------------

Trace/BPT trap

Trace/BPT trap

Trace/BPT trap

Trace/BPT trap

------------------------------------------------

Setting up the Ext2 partition...

------------------------------------------------

expr: non-integer argument '*'

[: -gt: argument expected

[: 0: unexpected operator

fdisk: Bad argument to the -s flag.

: Undefined error: 0

expr: syntax error

[: -: bad number

expr: syntax error

------------------------------------------------

Setting up swap...

------------------------------------------------

expr: non-integer argument '*'

[: -gt: argument expected

[: 0: unexpected operator

fdisk: Bad argument to the -s flag.

: Undefined error: 0

expr: syntax error

[: 0: unexpected operator

------------------------------------------------

Setting up BSD partition...

------------------------------------------------

fdisk: Bad argument to the -s flag.

: Undefined error: 0

expr: non-integer argument '*'

[: -gt: argument expected

[: 0: unexpected operator

expr: syntax error

expr: non-integer argument '*'

[: -gt: argument expected

[: 0: unexpected operator

expr: non-integer argument '*'

expr: non-integer argument '*'

[: 0: unexpected operator

expr: syntax error

[: -: bad number

expr: syntax error

expr: non-integer argument '*'

[: -gt: argument expected

[: 0: unexpected operator

expr: non-integer argument '*'

expr: non-integer argument '*'

[: 0: unexpected operator

expr: syntax error

[: 0: unexpected operator

disklabel: line 22: invalid format

disklabel: line 22: warning, unknown filesystem type: Ext2

disklabel: line 23: invalid format

disklabel: line 23: too few fields

Segmentation fault

------------------------------------------------

Setting up boot partition...

------------------------------------------------

mke2fs 1.19, 13-Jul-2000 for EXT2 FS 0.5b, 95/08/09

Filesystem label=

OS type: Linux

Block size=1024 (log=0)

Fragment size=1024 (log=0)

7712 inodes, 30743 blocks

0 blocks (0.00%) reserved for the super user

First data block=1

4 block groups

8192 blocks per group, 8192 fragments per group

1928 inodes per group

Superblock backups stored on blocks:

8193, 16385, 24577

Writing inode tables: 0/41/42/43/4done

Writing superblocks and filesystem accounting information: done

------------------------------------------------

Setting up /var...

------------------------------------------------

/dev/wd0f: 4195296 sectors in 4162 cylinders of 16 tracks, 63 sectors

2048.5MB in 13 cyl groups (330 c/g, 162.42MB/g, 19968 i/g)

super-block backups (for fsck -b #) at:

32, 332736, 665440, 998144, 1330848, 1663552, 1996256, 2328960,

2661664, 2994368, 3327072, 3659776, 3992480,

wtfs: write error for sector 16: Read-only file system

------------------------------------------------

Setting up /tmp...

------------------------------------------------

/dev/wd0g: 1024128 sectors in 1016 cylinders of 16 tracks, 63 sectors

500.1MB in 12 cyl groups (86 c/g, 42.33MB/g, 10368 i/g)

super-block backups (for fsck -b #) at:

32, 86784, 173536, 260288, 347040, 433792, 520544, 607296, 694048,

780800, 867552, 954304,

------------------------------------------------

Setting up root...

------------------------------------------------

/dev/wd0a: 73963008 sectors in 73376 cylinders of 16 tracks, 63 sectors

36114.8MB in 224 cyl groups (328 c/g, 161.44MB/g, 20352 i/g)

super-block backups (for fsck -b #) at:

32, 330720, 661408, 992096, 1322784, 1653472, 1984160,

2314848, 2645536, 2976224, 3306912, 3637600, 3968288, 4298976,

4629664, 4960352, 5290016, 5620704, 5951392, 6282080, 6612768,

6943456, 7274144, 7604832, 7935520, 8266208, 8596896, 8927584,

9258272, 9588960, 9919648, 10250336, 10580000, 10910688, 11241376,

11572064, 11902752, 12233440, 12564128, 12894816, 13225504, 13556192,

13886880, 14217568, 14548256, 14878944, 15209632, 15540320, 15869984,

16200672, 16531360, 16862048, 17192736, 17523424, 17854112, 18184800,

18515488, 18846176, 19176864, 19507552, 19838240, 20168928, 20499616,

20830304, 21159968, 21490656, 21821344, 22152032, 22482720, 22813408,

23144096, 23474784, 23805472, 24136160, 24466848, 24797536, 25128224,

25458912, 25789600, 26120288, 26449952, 26780640, 27111328, 27442016,

27772704, 28103392, 28434080, 28764768, 29095456, 29426144, 29756832,

30087520, 30418208, 30748896, 31079584, 31410272, 31739936, 32070624,

32401312, 32732000, 33062688, 33393376, 33724064, 34054752, 34385440,

34716128, 35046816, 35377504, 35708192, 36038880, 36369568, 36700256,

37029920, 37360608, 37691296, 38021984, 38352672, 38683360, 39014048,

39344736, 39675424, 40006112, 40336800, 40667488, 40998176, 41328864,

41659552, 41990240, 42319904, 42650592, 42981280, 43311968, 43642656,

43973344, 44304032, 44634720, 44965408, 45296096, 45626784, 45957472,

46288160, 46618848, 46949536, 47280224, 47609888, 47940576, 48271264,

48601952, 48932640, 49263328, 49594016, 49924704, 50255392, 50586080,

50916768, 51247456, 51578144, 51908832, 52239520, 52570208, 52899872,

53230560, 53561248, 53891936, 54222624, 54553312, 54884000, 55214688,

55545376, 55876064, 56206752, 56537440, 56868128, 57198816, 57529504,

57860192, 58189856, 58520544, 58851232, 59181920, 59512608, 59843296,

60173984, 60504672, 60835360, 61166048, 61496736, 61827424, 62158112,

62488800, 62819488, 63150176, 63479840, 63810528, 64141216, 64471904,

64802592, 65133280, 65463968, 65794656, 66125344, 66456032, 66786720,

67117408, 67448096, 67778784, 68109472, 68440160, 68769824, 69100512,

69431200, 69761888, 70092576, 70423264, 70753952, 71084640, 71415328,

71746016, 72076704, 72407392, 72738080, 73068768, 73399456, 73730144,

------------------------------------------------

Setting up boot partition......

------------------------------------------------



------------------------------------------------

Copying files...

------------------------------------------------



------------------------------------------------

Unpacking base.tgz...

------------------------------------------------

tlp0: receive error: MII error

tlp0: receive error: CRC error

tlp0: receive error: MII error

tlp0: receive error: CRC error

tlp0: receive error: CRC error

------------------------------------------------

Unpacking comp.tgz...

------------------------------------------------

tlp0: receive error: MII error

tlp0: receive error: CRC error

tlp0: receive error: CRC error

tlp0: receive error: MII error

tlp0: receive error: CRC error

------------------------------------------------

Unpacking etc.tgz...

------------------------------------------------



------------------------------------------------

Unpacking man.tgz...

------------------------------------------------

tlp0: receive error: MII error

tlp0: receive error: CRC error

------------------------------------------------

Unpacking misc.tgz...

------------------------------------------------

tlp0: receive error: MII error

tlp0: receive error: CRC error

------------------------------------------------

Unpacking text.tgz...

------------------------------------------------

tlp0: receive error: MII error

tlp0: receive error: CRC error

------------------------------------------------

Fixing up /dev...

------------------------------------------------



------------------------------------------------

Fixing up /etc...

------------------------------------------------



------------------------------------------------

Rebooting...

------------------------------------------------

Mar 9 22:15:01 reboot: rebooted by root syncing disks... done

rebooting...



ì

>> NetBSD/cobalt 1.6U Bootloader, Revision 0.1 [@0x81000000]

>> (cdi@merlin.camelot.net, Fri Jun 27 20:23:25 CEST 2003)

>> Memory: 262144 k

>> PROM boot string: root=/dev/hda1 ro

Loading: wd0a:netbsd

|/-\|2500768/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-
\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|
/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-
\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|
/-\|/-\|/+252384- [85488\|/-\+76831|/-\|]=0x2c7f6c

Starting at 0x80001000

invalid bootinfo (standalone boot?)

[ Kernel symbol table missing! ]

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004

The NetBSD Foundation, Inc. All rights reserved.

Copyright (c) 1982, 1986, 1989, 1991, 1993

The Regents of the University of California. All rights reserved.



NetBSD 2.0 (GENERIC) #0: Wed Dec 1 03:01:00 UTC 2004

builds@build:/big/builds/ab/netbsd-2-0-RELEASE/cobalt/200411300000Z-obj/big/
builds/ab/netbsd-2-0-RELEASE/src/sys/arch/cobalt/compile/GENERIC

total memory = 256 MB

avail memory = 247 MB

mainbus0 (root)

com0 at mainbus0 addr 0x1c800000 level 3: st16650a, working fifo

com0: console

cpu0 at mainbus0: QED RM5200 CPU (0x28a0) Rev. 10.0 with built-in FPU Rev.
10.0

cpu0: 32KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries

cpu0: 32KB/32B 2-way set-associative write-back L1 Data cache

panel0 at mainbus0 addr 0x1f000000

gt0 at mainbus0 addr 0x14000000

pci0 at gt0

pci0: i/o space, memory space enabled, rd/line, wr/inv ok

pchb0 at pci0 dev 0 function 0: Galileo GT-64111 System Controller, rev 1

tlp0 at pci0 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1

tlp0: interrupting at level 1

tlp0: Ethernet address 00:10:e0:00:5f:6e

lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3

lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto

siop0 at pci0 dev 8 function 0: Symbios Logic 53c860 (ultra scsi)

siop0: interrupting at irq 4

scsibus0 at siop0: 8 targets, 8 luns per target

pcib0 at pci0 dev 9 function 0

pcib0: VIA Technologies VT82C586 (Apollo VP) PCI-ISA Bridge, rev 37

viaide0 at pci0 dev 9 function 1

viaide0: VIA Technologies VT82C586 (Apollo VP) ATA33 controller

viaide0: bus-master DMA support present

viaide0: primary channel configured to compatibility mode

viaide0: primary channel interrupting at irq 14

atabus0 at viaide0 channel 0

viaide0: secondary channel configured to compatibility mode

viaide0: secondary channel interrupting at irq 15

atabus1 at viaide0 channel 1

VIA Technologies VT83C572 USB Controller (USB serial bus, revision 0x02) at
pci0 dev 9 function 2 not configured

tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1

tlp1: interrupting at level 2

tlp1: Ethernet address 00:10:e0:00:5f:6f

lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3

lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto

Kernelized RAIDframe activated

scsibus0: waiting 2 seconds for devices to settle...

wd0 at atabus0 drive 0INTRF

panic: siop_intr: I shouldn't be there !

Stopped at 0x801b5808: jr ra

bdslot: nop

db>