Subject: Re: Raq2 + restore cd NetBSD 2.0 results
To: Marcel <quest@cistron.nl>
From: Alex Pelts <alexp@broadcom.com>
List: port-cobalt
Date: 03/08/2005 11:18:50
It needs more than 512 mb to install automatically. It makes swap which 
is bad for flash disk anyway.

Thanks,
Alex


Marcel wrote:
> All,
> 
> After verifying the cd would boot (virtual pc) I started my laptop with it,
> boots fine. Then I started the Raq2, the LCD shows some info so does the
> console, so far so good. Suddenly kernel panic, disk too small... I'll be
> damned. I use 512MB SSD's and though it would work (CD is only ~200 megs) to
> create two ultra silent webservers, guess not.
> 
> Why does it needs so much space or does it use predefined sizes?
> 
> Marcel
> 
> 
> [Console output]
> 
> 
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002
>     The NetBSD Foundation, Inc.  All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>     The Regents of the University of California.  All rights reserved.
> 
> NetBSD 1.6.1 (INSTALL.LCD) #0: Thu Jun 26 22:29:11 CEST 2003
> 
> cdi@merlin.camelot.net:/misc/home/cdi/src/netbsd/1.6.1/src/sys/arch/cobalt/c
> ompile/INSTALL.LCD
> 256 MB memory, 234 MB free, 13208 KB in 3302 buffers
> mainbus0 (root)
> com0 at mainbus0 addr 0x1c800000 level 3: st16650a,
> com0: console
> cpu0 at mainbus0: QED RM5200 CPU (0x28a0) Rev. 10.0 with built-in FPU Rev.
> 10.0
> cpu0: 32KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries
> cpu0: 32KB/32B 2-way set-associative write-back L1 Data cache
> gt0 at mainbus0 addr 0x14000000
> pci0 at gt0
> pci0: i/o space, memory space enabled, rd/line, wr/inv ok
> pchb0 at pci0 dev 0 function 0: Galileo GT-64111 System Controller, rev 1
> tlp0 at pci0 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1
> tlp0: interrupting at level 1
> tlp0: Ethernet address 00:10:e0:00:5f:6e
> lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3
> lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> Symbios Logic 53c860 (SCSI mass storage, revision 0x02) at pci0 dev 8
> function 0
>  not configured
> pcib0 at pci0 dev 9 function 0
> pcib0: VIA Technologies VT82C586 (Apollo VP) PCI-ISA Bridge, rev 37
> pciide0 at pci0 dev 9 function 1: VIA Technologies VT82C586 (Apollo VP)
> ATA33 co
> ntroller
> pciide0: bus-master DMA support present
> pciide0: primary channel configured to compatibility mode
> wd0 at pciide0 channel 0 drive 1: <512MB CHH>
> wd0: drive supports 1-sector PIO transfers, LBA addressing
> wd0: 488 MB, 993 cyl, 16 head, 63 sec, 512 bytes/sect x 1000944 sectors
> wd0: 32-bit data port
> pciide0: primary channel interrupting at irq 14
> wd0(pciide0:0:1): using PIO mode 0
> pciide0: secondary channel configured to compatibility mode
> pciide0: disabling secondary channel (no drives)
> VIA Technologies VT83C572 USB Controller (USB serial bus, revision 0
>  dev 9 function 2 not configured
> tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1
> tlp1: interrupting at level 2
> tlp1: Ethernet address 00:10:e0:00:5f:6f
> lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3
> lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> lcd0 at mainbus0
> boot device: <unknown>
> root on tlp0
> nfs_boot: trying DHCP/BOOTP
> nfs_boot: DHCP next-server: 10.0.0.254
> nfs_boot: my_domain=mfg.cobaltmicro.com
> nfs_boot: my_addr=10.0.0.160
> nfs_boot: my_mask=255.0.0.0
> root on 10.0.0.254:/nfsroot
> warning: no /dev/console
> init: Creating mfs /dev
> Tue Mar  8 19:53:15 GMT 2005
> Starting file system checks:
> Coming up: fixing /dev...
> Coming up: fixing /var...
> Preparing the installation...
> Setting tty flags.
> Setting sysctl variables:
> Starting network.
> Hostname: client
> Configuring network interfaces:.
> Building databases...
> kvm_mkdb: machdep.booted_kernel: the value is not available: No such file or
> dir
> ectory
> Mounting all filesystems...
> Checking quotas: done.
> Setting securelevel: kern.secu
> /etc/rc: WARNING: No swap space configured!
> starting local daemons:wd0: no disk label
> 
>  ------------------------------------------------ 
>   Setting up the disk...
>  ------------------------------------------------ 
> 
> mknod: /dev/lcd: File exists
> 
>  ------------------------------------------------ 
>   Clearing partition information...
>  ------------------------------------------------ 
> 
> wd0: no disk label
> wd0: no disk label
> wd0: no disk label
> wd0: no disk label
> 
>  ------------------------------------------------
>   Setting up the Ext2 partition...
>  ------------------------------------------------
> 
> wd0: no disk label
> 
>  ------------------------------------------------
>   Setting up swap...
>  ------------------------------------------------
> 
> wd0: no disk label
> 
>  ------------------------------------------------
>   PANIC: disk is too small...
>  ------------------------------------------------
> 
> Tue Mar  8 19:53:58 GMT 2005
> 
> NetBSD/cobalt (client) (tty00)
> 
> login:
> 
> 
> 
>