Port-arm archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
NetBSD on ODROID-C1
ODROID-C1 is a quad core Cortex-A5 board (only $35!) from Hardkernel:
http://www.hardkernel.com/main/products/prdt_info.php
So far I have serial console, USB, and SMP working. It boots multiuser on
-current. dmesg below.
Cheers,
Jared
QA5:A;SVN:B72;POC:17F;STS:0;BOOT:0;INIT:10;BOOT:1;INIT:0;READ:0;CHECK:0;PASS:1;
-----------------------------------------------------------------------
* Welcome to Hardkernel's ODROID-C... (Built at 19:33:00 Dec 8 2014) *
-----------------------------------------------------------------------
CPU : AMLogic S805
MEM : 1024MB (DDR3@792MHz)
BID : HKC13C0001
S/N : HKC1CC037EBE432C
0x0000009f
check SD_boot_type:0x1 card_type:0x1
Loading U-boot...success.
U-boot-00000-ge7d4447(odroidc@odroidc-v2011.03) (Feb 04 2015 - 20:50:13)
DRAM: 1 GiB
relocation Offset is: 2ff08000
MMC: SDCARD: 0, eMMC: 1
IR init is done!
vpu clk_level = 3
set vpu clk: 182150000Hz, readback: 182150000Hz(0x701)
mode = 6 vic = 4
set HDMI vic: 4
mode is: 6
viu chan = 1
config HPLL
config HPLL done
reconfig packet setting done
MMC read: dev # 0, block # 33984, count 12288 ... 12288 blocks read: OK
There is no valid bmp file at the given address
============================================================
Vendor: Man 1b534d Snr 76f0b173 Rev: 1.0 Prod: 00000
Type: Removable Hard Disk
Capacity: 3884.0 MB = 3.7 GB (7954432 x 512)
------------------------------------------------------------
Partition Start Sector Num Sectors Type
1 2048 78277 c
2 80325 1494045 83
============================================================
Net: Meson_Ethernet
init suspend firmware done. (ret:0)
Hit Enter key to stop autoboot -- : 0
exit abortboot: 0
reading boot.ini
1392 bytes read
Loading boot.ini from mmc0:1 (vfat)
Executing the script...
setenv m "1080p" # 1080P 1920x1080
setenv vout_mode "hdmi"
setenv m_bpp "32"
setenv disableuhs "disableuhs"
setenv bootargs "root=sd0a"
setenv bootcmd "fatload mmc 0:1 0x21000000 netbsd.ub; bootm 0x21000000"
run bootcmd
reading netbsd.ub
4811648 bytes read
## Booting kernel from Legacy Image at 21000000 ...
Image Name: NetBSD/amlogic 7.99.5
Image Type: ARM NetBSD Kernel Image (uncompressed)
Data Size: 4811584 Bytes = 4.6 MiB
Load Address: 00100000
Entry Point: 00100000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
uboot time: 5027565 us.
## Transferring control to NetBSD stage-2 loader (at address 00100000) ...
[ Kernel symbol table missing! ]
Loaded initial symtab at 0x804ff5f8, strtab at 0x8053aa98, # entries 15159
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 7.99.5 (ODROID-C1) #203: Tue Mar 3 19:18:44 AST 2015
Jared@Jared-PC:/cygdrive/d/netbsd/src/sys/arch/evbarm/compile/obj/ODROID-C1
total memory = 1024 MB
avail memory = 1008 MB
sysctl_createv: sysctl_create(machine_arch) returned 17
mainbus0 (root)
cpu0 at mainbus0 core 0: 1200 MHz Cortex-A5 r0p1 (Cortex V7A core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB/32B 2-way L1 VIPT Instruction cache
cpu0: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu0: 512KB/32B 8-way **unknown 12** L2 PIPT Unified cache
vfp0 at cpu0: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu1 at mainbus0 core 1
cpu2 at mainbus0 core 2
cpu3 at mainbus0 core 3
armperiph0 at mainbus0
armgic0 at armperiph0: Generic Interrupt Controller, 256 sources (245 valid)
armgic0: 32 Priorities, 224 SPIs, 5 PPIs, 16 SGIs
a9tmr0 at armperiph0: A9 Global 64-bit Timer (300 MHz)
a9tmr0: interrupting on irq 27
a9wdt0 at armperiph0: A9 Watchdog Timer, default period is 12 seconds
arml2cc0 at armperiph0: ARM PL310 r3p3 L2 Cache Controller (disabled)
arml2cc0: cache enabled
amlogicio0 at mainbus0
amlogiccom0 at amlogicio0 port 0: console
amlogiccom0: interrupting at irq 122
dwctwo0 at amlogicio0 port 0: USB controller
dwctwo1 at amlogicio0 port 1: USB controller
usb0 at dwctwo0: USB revision 2.0
usb1 at dwctwo1: USB revision 2.0
cpu1: 1200 MHz Cortex-A5 r0p1 (Cortex V7A core)
cpu1: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu1: 32KB/32B 2-way L1 VIPT Instruction cache
cpu1: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu1: 512KB/32B 8-way **unknown 12** L2 PIPT Unified cache
vfp1 at cpu1: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu3: 1200 MHz Cortex-A5 r0p1 (Cortex V7A core)
cpu3: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu3: 32KB/32B 2-way L1 VIPT Instruction cache
cpu3: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu3: 512KB/32B 8-way **unknown 12** L2 PIPT Unified cache
vfp3 at cpu3: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu2: 1200 MHz Cortex-A5 r0p1 (Cortex V7A core)
cpu2: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu2: 32KB/32B 2-way L1 VIPT Instruction cache
cpu2: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu2: 512KB/32B 8-way **unknown 12** L2 PIPT Unified cache
vfp2 at cpu2: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
uhub0 at usb0: vendor 0000 DWC2 root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1 at usb1: vendor 0000 DWC2 root hub, class 9/0, rev 2.00/1.00, addr 1
WARNING: module error: can't find builtin dependency `iic'
WARNING: module error: can't find builtin dependency `au8522'
WARNING: module error: can't find builtin dependency `iic'
WARNING: module error: can't find builtin dependency `iic'
WARNING: module error: can't find builtin dependency `iic'
WARNING: module error: can't find builtin dependency `iic'
uhub2 at uhub1 port 1: vendor 05e3 USB2.0 Hub, class 9/0, rev 2.00/32.98, addr 2
uhub2: multiple transaction translators
umass0 at uhub2 port 1 configuration 1 interface 0
umass0: SanDisk Cruzer, rev 2.00/1.03, addr 3
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <SanDisk, Cruzer, 1.20> disk removable
sd0: 7633 MB, 15509 cyl, 16 head, 63 sec, 512 bytes/sect x 15633408 sectors
boot device: sd0
root on sd0a dumps on sd0b
mountroot: trying nfs...
mountroot: trying msdos...
mountroot: trying ffs...
root file system type: ffs
kern.module.path=/stand/evbarm/7.99.5/modules
WARNING: no TOD clock present
WARNING: using filesystem time
WARNING: CHECK AND RESET THE DATE!
warning: no /dev/console
init: copying out path `/sbin/init' 11
Kernel RNG "kernel" long run test FAILURE: Run of 26 1s found
cprng kernel: failed statistical RNG test
Kernel RNG "kernel" monobit test FAILURE: 10296 ones
cprng kernel: failed statistical RNG test
Kernel RNG "kernel" runs test FAILURE: too few runs of 4 0s (239 < 240)
cprng kernel: failed statistical RNG test
Kernel RNG "kernel" runs test FAILURE: too many runs of 4 0s (384 > 384)
cprng kernel: failed statistical RNG test
Sun Mar 1 18:59:04 UTC 2015
Starting root file system check:
/dev/rsd0a: file system is clean; not checking
Starting file system checks:
random_seed: /var/db/entropy-file: Not present
Setting tty flags.
WARNING: module error: vfs load failed for `compat', error 2
WARNING: module error: vfs load failed for `compat', error 2
WARNING: module error: vfs load failed for `com', error 2
WARNING: module error: vfs load failed for `com', error 2
Setting sysctl variables:
ddb.onpanic: 1 -> 0
Starting network.
Hostname: empusa
IPv6 mode: host
Configuring network interfaces:.
Adding interface aliases:.
Waiting for DAD completion for statically configured addresses...
Building databases: dev, utmp, utmpx.
Starting syslogd.
Mounting all file systems...
Clearing temporary files.
Creating a.out runtime link editor directory cache.
Checking quotas: done.
Setting securelevel: kern.securelevel: 0 -> 1
Starting virecover.
Starting local daemons:.
Updating motd.
Starting inetd.
Starting cron.
Sun Mar 1 18:59:30 UTC 2015
NetBSD/evbarm (empusa) (console)
login: root
Mar 1 18:59:36 empusa login: ROOT LOGIN (root) on tty console
Last login: Sun Mar 1 18:58:56 2015 on console
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 7.99.5 (ODROID-C1) #203: Tue Mar 3 19:18:44 AST 2015
Welcome to NetBSD!
This system is running a beta release of the NetBSD operating system, aimed
at stabilizing the next formal release. It is close to formal release quality,
but may still contain bugs, even serious ones. Please bear this in mind and
use the system with care.
You are encouraged to test this version as thoroughly as possible. Should you
encounter any problem, please report it back to the development team using the
send-pr(1) utility (requires a working MTA). If yours is not properly set up,
use the web interface at: http://www.NetBSD.org/support/send-pr.html
Thank you for helping us test and improve this beta NetBSD release.
Terminal type is vt100.
We recommend that you create a non-root account and use su(1) for root access.
empusa# openssl speed md5
WARNING: can't open config file: /etc/openssl/openssl.cnf
Doing md5 for 3s on 16 size blocks: 318444 md5's in 3.02s
Doing md5 for 3s on 64 size blocks: 301452 md5's in 3.01s
Doing md5 for 3s on 256 size blocks: 252196 md5's in 3.01s
Doing md5 for 3s on 1024 size blocks: 152042 md5's in 3.00s
Doing md5 for 3s on 8192 size blocks: 32272 md5's in 3.00s
OpenSSL 1.0.1k 8 Jan 2015
NetBSD 7.0_BETA
options:bn(32,32) md2(int) rc4(ptr,int) des(idx,cisc,2,long) aes(partial) idea(int) blowfish(idx)
gcc version 4.8.4 (NetBSD nb2 20150115)
The 'numbers' are in 1000s of bytes per second processed.
type 16 bytes 64 bytes 256 bytes 1024 bytes 8192 bytes
md5 1687.12k 6409.61k 21449.23k 51897.00k 88124.07k
empusa#
Home |
Main Index |
Thread Index |
Old Index