dmesg from Rockchip RK3188+ (Minix Neo X7)

[Jared McNeill <jmcneill%invisible.ca@localhost>]

Cheap TV STB I picked up on Newegg. PCB is marked "VER3.0" and had TTL 
pins to hook up a serial port.

Seems similar to Radxa Rock Pro except it has an RK3188+ instead of 
RK3188, and uses a USB ethernet controller instead of the one built into 
the SoC.

Working so far:
 - SMP (4 cores)
 - CPU frequency scaling - 600MHz to 1.6GHz
 - USB (DWC2)
 - Ethernet (USB Realtek RTL8152B)
 - MMC
 - Power Management IC (ACT8846)
 - I2C
 - RAM detection (but usage is currently limited to 1GB; board has 2GB)


DDR Version 1.04 20130830
In
DDR3
300MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=2 Die Bus-Width=16 Size=2048MB
Memory OK
OUT


U-Boot 2014.01-g89b5cf5 (Dec 30 2014 - 13:39:38)

ChipVer: 310B20130131V101
CPU:    RK3188+
Board:  RK30xx platform Board
total reserving memory(except stack) is :48m
DRAM:  2 GiB
arch_interrupt_init
DMAInit: OK
SdmmcInit=0 0
FwPartOffset=2000 , 0
storage init OK!
Using default environment

In:    serial
Out:   serial
Err:   serial
board_late_init
unsigned!
SecureBootEn = 0 0
##################################################
uboot version: U-Boot 2014.01-g89b5cf5 (Dec 30 2014 - 13:39:38)

#Boot ver: 0000-00-00#0.00

##################################################
setup gpio int
GetParam
check parameter success
partition(uboot): offset=0x00002000, size=0x00002000
partition(misc): offset=0x00004000, size=0x00002000
partition(kernel): offset=0x00006000, size=0x00008000
partition(boot): offset=0x0000E000, size=0x00010000
empty serial no.
checkKey
vbus = 1
lcd_ctrl_init [38]
i2c init OVER in board!
set_lcdc_dclk: lcdc_source_clk = 768, clk = 71, div = 11
rk30_load_screen for lcdc ok!
lcd_enable [55]
In charging!
SecureBootCheckOK:0
booti: do_bootm_linux...

Starting kernel ...

@defgprobe the PL310 L2CC
l
uboot arg = 0, 0xbfa, 0x60088000, 0x610a6be0
initarm: cbar=0x1013c000
KERNEL_BASE=0x80000000, KERNEL_VM_BASE=0xc0000000, KERNEL_VM_BASE - 
KERNEL_BASE=0x40000000, KERNEL_BASE_VOFFSET=0x20000000
initarm: dropping RAM size from 2048MB to 1024MB
ram_size = 0x40000000
bootargs: -s console=ttyFIQ0 androidboot.console=ttyFIQ0 init=/init 
initrd=0x62000000,0x004C0000 
mtdparts=rk29xxnand:0x00002000@0x00002000(uboot),0x00002000@0x00004000(misc),0x00008000@0x00006000(kernel),0x00010000@0x0000e000(boot) 
androidboot.bootloader=fastboot fb.addr=0x63c08000 
chipver=310B20130131V101 androidboot.serialno=0123456789
[ Kernel symbol table missing! ]
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 7.99.3 (ROCKCHIP) #555: Sun Jan  4 13:21:41 AST 2015

jmcneill@localhost.localdomain:/home/jmcneill/netbsd/src/sys/arch/evbarm/compile/obj/ROCKCHIP
total memory = 1024 MB
avail memory = 1008 MB
sysctl_createv: sysctl_create(machine_arch) returned 17
mainbus0 (root)
cpu0 at mainbus0 core 0: 600 MHz Cortex-A9 r4p0 (Cortex V7A core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB/32B 4-way L1 VIPT Instruction cache
cpu0: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu0: 512KB/32B 16-way write-back-locking-D L2 PIPT Unified cache
vfp0 at cpu0: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu1 at mainbus0 core 1
cpu2 at mainbus0 core 2
cpu3 at mainbus0 core 3
armperiph0 at mainbus0
arml2cc0 at armperiph0: ARM PL310 r3p2 L2 Cache Controller (disabled)
arml2cc0: cache enabled
armgic0 at armperiph0: Generic Interrupt Controller, 160 sources (149 
valid)
armgic0: 32 Priorities, 128 SPIs, 5 PPIs, 16 SGIs
a9tmr0 at armperiph0: A9 Global 64-bit Timer (150 MHz)
a9tmr0: interrupting on irq 27
a9wdt0 at armperiph0: A9 Watchdog Timer, default period is 12 seconds
obio0 at mainbus0: On-board I/O
grf iomux: old 00005554, new 55555554, renew 00005554
grf iomux: old 00000000, new 00050001, renew 00000001
grf iomux: old 00001000, new 3c000000, renew 00000000
grf iomux: old 00000000, new 55555555, renew 00005555
grf iomux: old 00000001, new a000a000, renew 0000a001
grf iomux: old 00000006, new f800f800, renew 0000f806
grf iomux: old 00000000, new ffffaaaa, renew 0000aaaa
grf iomux: old 00000000, new 003f000a, renew 0000000a
grf iomux: old 0000f806, new 00030002, renew 0000f806
grf iomux: old 0000c904, new 000f000f, renew 0000c90f
gpio: 0x0000a000 0x00000104 -> 0x0000010c
gpio: 0x0000a004 0x00000104 -> 0x0000010c
gpio: 0x0003e000 0x00000000 -> 0x80000000
gpio: 0x0003e004 0x00000000 -> 0x80000000
gpio: 0x00080000 0x00000000 -> 0x04000000
gpio: 0x00080004 0x00000000 -> 0x04000000
gpio: 0x0000a000 0x0000010c -> 0x4000010c
gpio: 0x0000a004 0x0000010c -> 0x4000010c
gpio: 0x00080000 0x04000000 -> 0x04000400
gpio: 0x00080004 0x04000000 -> 0x04000400
rkiic0 at obio0: addr 0x2002d000-0x2002dfff intr 72 port 0: I2C0
iic0 at rkiic0: I2C bus
rkiic1 at obio0: addr 0x2002f000-0x2002ffff intr 73 port 1: I2C1
iic1 at rkiic1: I2C bus
act8846pm0 at iic1 addr 0x5a
act8846pm0: DCDC1: [1.200V] [ON]
act8846pm0: DCDC2: [1.000V] [ON]
act8846pm0: DCDC3: [1.000V] [ON]
act8846pm0: DCDC4: [3.000V] [ON]
act8846pm0: LDO1: [1.000V] [ON]
act8846pm0: LDO2: [1.200V] [OFF]
act8846pm0: LDO3: [1.800V] [OFF]
act8846pm0: LDO4: [3.300V] [OFF]
act8846pm0: LDO5: [3.300V] [OFF]
act8846pm0: LDO6: [3.300V] [OFF]
act8846pm0: LDO7: [1.800V] [ON]
act8846pm0: LDO8: [2.800V] [OFF]
rkiic2 at obio0: addr 0x20056000-0x20057fff intr 74 port 2: I2C2
iic2 at rkiic2: I2C bus
rkiic3 at obio0: addr 0x2005a000-0x2005bfff intr 75 port 3: I2C3
iic3 at rkiic3: I2C bus
rkiic4 at obio0: addr 0x2005e000-0x2005ffff intr 84 port 4: I2C4
iic4 at rkiic4: I2C bus
rktimer0 at obio0: addr 0x20038000-0x20039fff
: ns16550a, working fifo064000-0x200643ff intr 68 mult 4
com0: console
dwctwo0 at obio0: addr 0x10180000-0x101bffff intr 48: USB controller
dwctwo1 at obio0: addr 0x101c0000-0x101fffff intr 49: USB controller
dwcmmc0 at obio0: addr 0x10214000-0x10217fff intr 55: SD/MMC controller
rkemac0 at obio0: addr 0x10204000-0x10207fff intr 51: Ethernet controller
rkemac0: Ethernet address: f2:00:f2:0a:60:ec
rkemac0: no PHY found!
usb0 at dwctwo0: USB revision 2.0
usb1 at dwctwo1: USB revision 2.0
cpu3: 600 MHz Cortex-A9 r4p0 (Cortex V7A core)
cpu3: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu3: 32KB/32B 4-way L1 VIPT Instruction cache
cpu3: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu3: 512KB/32B 16-way write-back-locking-D L2 PIPT Unified cache
vfp3 at cpu3: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu1: 600 MHz Cortex-A9 r4p0 (Cortex V7A core)
cpu1: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu1: 32KB/32B 4-way L1 VIPT Instruction cache
cpu1: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu1: 512KB/32B 16-way write-back-locking-D L2 PIPT Unified cache
vfp1 at cpu1: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu2: 600 MHz Cortex-A9 r4p0 (Cortex V7A core)
cpu2: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu2: 32KB/32B 4-way L1 VIPT Instruction cache
cpu2: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu2: 512KB/32B 16-way write-back-locking-D L2 PIPT Unified cache
vfp2 at cpu2: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
sdmmc0 at dwcmmc0
uhub0 at usb0: vendor 0000 DWC2 root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1 at usb1: vendor 0000 DWC2 root hub, class 9/0, rev 2.00/1.00, addr 1
ld0 at sdmmc0: <0x03:0x5344:SU08G:0x80:0x1cda770b:0x0ca>
ld0: 7580 MB, 3850 cyl, 64 head, 63 sec, 512 bytes/sect x 15523840 sectors
ld0: 4-bit width, bus clock 48.000 MHz
uhub2 at uhub1 port 1: SMSC USB 2.0 4-Port Hub, class 9/0, rev 2.00/b.b3, 
addr 2
uhub2: multiple transaction translators
cdce0 at uhub2 port 1 configuration 2 interface 0
cdce0: Realtek USB 10/100 LAN, rev 2.10/20.00, addr 3
cdce0: address 10:00:00:2c:64:eb
urtwn0 at uhub2 port 3
urtwn0: Realtek 802.11n WLAN Adapter, rev 2.00/2.00, addr 4
urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R, address 80:1f:02:94:40:12
urtwn0: 1 rx pipe, 2 tx pipes
urtwn0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
urtwn0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 
24Mbps 36Mbps 48Mbps 54Mbps
boot device: <unknown>
root device: ld0a
dump device (default ld0b):
file system (default generic):
root on ld0a dumps on ld0b
root file system type: ffs
kern.module.path=/stand/evbarm/7.99.3/modules
WARNING: no TOD clock present
WARNING: using filesystem time
WARNING: CHECK AND RESET THE DATE!
warning: no /dev/console
init path (default /sbin/init):
init: trying /sbin/init
Kernel RNG "kernel" monobit test FAILURE: 9692 ones
Kernel RNG "kernel" runs test FAILURE: too many runs of 6 0s (216 > 209)
cprng kernel: failed statistical RNG test
Kernel RNG "kernel" poker test failure: parameter X = 1.62560
cprng kernel: failed statistical RNG test
Enter pathname of shell or RETURN for /bin/sh:
Terminal type is vt100.
We recommend that you create a non-root account and use su(1) for root 
access.
# ^DMon Dec 29 15:42:54 UTC 2014
Starting root file system check:
/dev/rld0a: file system is clean; not checking
Starting file system checks:
random_seed: /var/db/entropy-file: Not present
Setting tty flags.
Setting sysctl variables:
ddb.onpanic: 1 -> 0
Starting network.
Hostname: clotho
IPv6 mode: host
Configuring network interfaces:.
Adding interface aliases:.
Waiting for DAD completion for statically configured addresses...
Starting wpa_supplicant.
Starting dhcpcd.
Building databases: dev, utmp, utmpx.
Starting syslogd.
Mounting all file systems...
Clearing temporary files.
Creating a.out runtime link editor directory cache.
Checking quotas: done.
Setting securelevel: kern.securelevel: 0 -> 1
Starting virecover.
Starting local daemons:.
Updating motd.
Starting inetd.
Starting cron.
Mon Dec 29 15:43:39 UTC 2014

NetBSD/evbarm (clotho) (console)

login: root
Dec 29 15:43:49 clotho login: ROOT LOGIN (root) on tty console
Last login: Mon Dec 29 15:38:41 2014 on console
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 7.99.3 (ROCKCHIP) #555: Sun Jan 4 13:21:41 AST 2015

Welcome to NetBSD!

This system is running a beta release of the NetBSD operating system, 
aimed
at stabilizing the next formal release.  It is close to formal release 
quality,
but may still contain bugs, even serious ones.  Please bear this in mind 
and
use the system with care.

You are encouraged to test this version as thoroughly as possible.  Should 
you
encounter any problem, please report it back to the development team using 
the
send-pr(1) utility (requires a working MTA).  If yours is not properly set 
up,
use the web interface at: http://www.NetBSD.org/support/send-pr.html

Thank you for helping us test and improve this beta NetBSD release.


You have new mail.
Terminal type is vt100.
We recommend that you create a non-root account and use su(1) for root 
access.
clotho# sysctl machdep.cpu
machdep.cpu.frequency.target = 600
machdep.cpu.frequency.current = 600
machdep.cpu.frequency.available = 1608 1416 1200 1008 816 600
clotho# sysctl -w machdep.cpu.frequency.target=1608
machdep.cpu.frequency.target: 600 -> 1608
clotho#