dmesg from Rockchip RK3188/PX2

To: port-arm%netbsd.org@localhost
Subject: dmesg from Rockchip RK3188/PX2
From: FUKAUMI Naoki <naoki%fukaumi.org@localhost>
Date: Wed, 31 Dec 2014 13:33:20 +0900

Hi,

by jmcneill's hard work, NetBSD for Rockchip is getting better.
thank you very much for your work!

[Radxa Rock Pro]
------------------------------------------------------------------------
DDR Version 1.04 20130830
In
DDR3
300MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=2 Die Bus-Width=16 Size=2048MB
Memory OK
OUT


U-Boot 2014.01-gf05df7b (Dec 30 2014 - 13:38:39)

ChipVer: 310B20121130V100
CPU:	RK3188
Board:	RK30xx platform Board
total reserving memory(except stack) is :48m
DRAM:  2 GiB
arch_interrupt_init
DMAInit: OK
storage init OK!
Using default environment

In:    serial
Out:   serial
Err:   serial
board_late_init
unsigned!
SecureBootEn = 0 0
##################################################
uboot version: U-Boot 2014.01-gf05df7b (Dec 30 2014 - 13:38:39)

#Boot ver:

##################################################
setup gpio int
GetParam
LMemApiReadLba:0
check parameter success
partition(uboot): offset=0x00002000, size=0x00002000
partition(misc): offset=0x00004000, size=0x00002000
partition(kernel): offset=0x00006000, size=0x00008000
partition(boot): offset=0x0000E000, size=0x00010000
empty serial no.
checkKey
vbus = 1
lcd_ctrl_init [38]
i2c init OVER in board!
set_lcdc_dclk: lcdc_source_clk = 768, clk = 71, div = 11
rk30_load_screen for lcdc ok!
lcd_enable [55]
In charging!
LMemApiReadLba:0
LMemApiReadLba:0
LMemApiReadLba:0
LMemApiReadLba:0
LMemApiReadLba:0
SecureBootCheckOK:0
booti: do_bootm_linux...

Starting kernel ...

@defgprobe the PL310 L2CC
l
uboot arg = 0, 0xbfa, 0x60088000, 0x610a5be0
initarm: cbar=0x1013c000

KERNEL_BASE=0x80000000, KERNEL_VM_BASE=0xc0000000, KERNEL_VM_BASE -KERNEL_BASE=0x40000000, KERNEL_BASE_VOFFSET=0x20000000

initarm: dropping RAM size from 2048MB to 1024MB
ram_size = 0x40000000

bootargs: console=ttyFIQ0 androidboot.console=ttyFIQ0 init=/initinitrd=0x62000000,0x004D0000mtdparts=rk29xxnand:0x00002000@0x00002000(uboot),0x00002000@0x00004000(misc),0x00008000@0x00006000(kernel),0x00010000@0x0000e000(boot)androidboot.bootloader=fastboot fb.addr=0x63c08000chipver=310B20121130V100 androidboot.serialno=0123456789

[ Kernel symbol table missing! ]
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 7.99.3 (ROCKCHIP) #1: Wed Dec 31 13:17:42 JST 2014
	fun@build:/home/fun/rockchip/netbsd-src/sys/arch/evbarm/compile/obj/ROCKCHIP
total memory = 1024 MB
avail memory = 1008 MB
sysctl_createv: sysctl_create(machine_arch) returned 17
mainbus0 (root)
cpu0 at mainbus0 core 0: 600 MHz Cortex-A9 r4p0 (Cortex V7A core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB/32B 4-way L1 VIPT Instruction cache
cpu0: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu0: 512KB/32B 16-way write-back-locking-D L2 PIPT Unified cache
vfp0 at cpu0: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu1 at mainbus0 core 1
cpu2 at mainbus0 core 2
cpu3 at mainbus0 core 3
armperiph0 at mainbus0
arml2cc0 at armperiph0: ARM PL310 r3p2 L2 Cache Controller (disabled)
arml2cc0: cache enabled
armgic0 at armperiph0: Generic Interrupt Controller, 160 sources (149 valid)
armgic0: 32 Priorities, 128 SPIs, 5 PPIs, 16 SGIs
a9tmr0 at armperiph0: A9 Global 64-bit Timer (150 MHz)
a9tmr0: interrupting on irq 27
a9wdt0 at armperiph0: A9 Watchdog Timer, default period is 12 seconds
obio0 at mainbus0: On-board I/O
grf iomux: old 00005554, new 55555554, renew 00005554
grf iomux: old 00000000, new 00050001, renew 00000001
grf iomux: old 00001000, new 3c000000, renew 00000000
gpio: 0x0000a000 0x00000104 -> 0x0000010c
gpio: 0x0000a004 0x00000104 -> 0x0000010c
gpio: 0x0003e000 0x00000000 -> 0x80000000
gpio: 0x0003e004 0x00000000 -> 0x80000000

com0 at obio0: addr 0x20064000-0x200643ff intr 68 mult 4: ns16550a,working fifo

com0: console
dwctwo0 at obio0: addr 0x10180000-0x101bffff intr 48: USB controller
dwctwo1 at obio0: addr 0x101c0000-0x101fffff intr 49: USB controller
dwcmmc0 at obio0: addr 0x10214000-0x10217fff intr 55: SD/MMC controller
dwcmmc2 at obio0: addr 0x1021c000-0x1021ffff intr 57: SD/MMC controller
rkiic0 at obio0: addr 0x2002c000-0x2002dfff intr 72 port 0: I2C0
iic0 at rkiic0: I2C bus
rkiic1 at obio0: addr 0x2002e000-0x2002ffff intr 73 port 1: I2C1
iic1 at rkiic1: I2C bus
rkiic2 at obio0: addr 0x20054000-0x20057fff intr 74 port 2: I2C2
iic2 at rkiic2: I2C bus
rkiic3 at obio0: addr 0x20058000-0x2005bfff intr 75 port 3: I2C3
iic3 at rkiic3: I2C bus
rkiic4 at obio0: addr 0x2005c000-0x2005ffff intr 84 port 4: I2C4
iic4 at rkiic4: I2C bus
usb0 at dwctwo0: USB revision 2.0
usb1 at dwctwo1: USB revision 2.0
cpu1: 600 MHz Cortex-A9 r4p0 (Cortex V7A core)
cpu1: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu1: 32KB/32B 4-way L1 VIPT Instruction cache
cpu1: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu1: 512KB/32B 16-way write-back-locking-D L2 PIPT Unified cache
vfp1 at cpu1: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu2: 600 MHz Cortex-A9 r4p0 (Cortex V7A core)
cpu2: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu2: 32KB/32B 4-way L1 VIPT Instruction cache
cpu2: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu2: 512KB/32B 16-way write-back-locking-D L2 PIPT Unified cache
vfp2 at cpu2: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu3: 600 MHz Cortex-A9 r4p0 (Cortex V7A core)
cpu3: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu3: 32KB/32B 4-way L1 VIPT Instruction cache
cpu3: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu3: 512KB/32B 16-way write-back-locking-D L2 PIPT Unified cache
vfp3 at cpu3: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
sdmmc0 at dwcmmc0
sdmmc1 at dwcmmc2
uhub0 at usb0: vendor 0000 DWC2 root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1 at usb1: vendor 0000 DWC2 root hub, class 9/0, rev 2.00/1.00, addr 1
sdmmc1: couldn't enable card: 60
ld0 at sdmmc0: <0x02:0x544d:SA04G:0x04:0x9c38c4f0:0x09b>
ld0: 3776 MB, 1917 cyl, 64 head, 63 sec, 512 bytes/sect x 7733248 sectors
ld0: 4-bit width, bus clock 24.000 MHz

uhub2 at uhub1 port 1: Genesys Logic USB2.0 Hub, class 9/0, rev2.00/85.36, addr 2

uhub2: single transaction translator
ugen0 at uhub2 port 1
ugen0: Realtek 802.11n WLAN Adapter, rev 2.00/2.00, addr 3
boot device: <unknown>
root device:
------------------------------------------------------------------------

[Rayeager PX2]
------------------------------------------------------------------------
DDR Version 1.04 20130517
In
DDR3
300MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=2 Die Bus-Width=16 Size=2048MB
Memory OK
OUT


U-Boot 2014.01-gf3bf10e (Dec 30 2014 - 13:42:29)

ChipVer: 300A20111111V101
CPU:	RK3066
Board:	RK30xx platform Board
total reserving memory(except stack) is :48m
DRAM:  2 GiB
arch_interrupt_init
DMAInit: OK
SdmmcInit=2 0
FwPartOffset=2000 , 0
storage init OK!
Using default environment

In:    serial
Out:   serial
Err:   serial
board_late_init
unsigned!
SecureBootEn = 0 0
##################################################
uboot version: U-Boot 2014.01-gf3bf10e (Dec 30 2014 - 13:42:29)

#Boot ver: 2014-12-05#0.02

##################################################
setup gpio int
GetParam
check parameter success
partition(uboot): offset=0x00002000, size=0x00002000
partition(misc): offset=0x00004000, size=0x00002000
partition(kernel): offset=0x00006000, size=0x00008000
partition(boot): offset=0x0000E000, size=0x00010000
empty serial no.
checkKey
vbus = 1
lcd_ctrl_init [38]
i2c init OVER in board!
set_lcdc_dclk: lcdc_source_clk = 768, clk = 71, div = 11
rk30_load_screen for lcdc ok!
lcd_enable [55]
backlight --- brightness:50
In charging!
SecureBootCheckOK:0
booti: do_bootm_linux...

Starting kernel ...

@defgprobe the PL310 L2CC
l
uboot arg = 0, 0xbfa, 0x60088000, 0x610a5be0
initarm: cbar=0x1013c000

KERNEL_BASE=0x80000000, KERNEL_VM_BASE=0xc0000000, KERNEL_VM_BASE -KERNEL_BASE=0x40000000, KERNEL_BASE_VOFFSET=0x20000000

initarm: dropping RAM size from 2048MB to 1024MB
ram_size = 0x40000000

[ Kernel symbol table missing! ]
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 7.99.3 (ROCKCHIP) #0: Wed Dec 31 12:52:28 JST 2014
	fun@build:/home/fun/rockchip/netbsd-src/sys/arch/evbarm/compile/obj/ROCKCHIP
total memory = 1024 MB
avail memory = 1008 MB
sysctl_createv: sysctl_create(machine_arch) returned 17
mainbus0 (root)
cpu0 at mainbus0 core 0: 600 MHz Cortex-A9 r4p0 (Cortex V7A core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB/32B 4-way L1 VIPT Instruction cache
cpu0: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu0: 512KB/32B 16-way write-back-locking-D L2 PIPT Unified cache
vfp0 at cpu0: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu1 at mainbus0 core 1
armperiph0 at mainbus0
arml2cc0 at armperiph0: ARM PL310 r3p2 L2 Cache Controller (disabled)
arml2cc0: cache enabled
armgic0 at armperiph0: Generic Interrupt Controller, 160 sources (149 valid)
armgic0: 32 Priorities, 128 SPIs, 5 PPIs, 16 SGIs
a9tmr0 at armperiph0: A9 Global 64-bit Timer (150 MHz)
a9tmr0: interrupting on irq 27
a9wdt0 at armperiph0: A9 Watchdog Timer, default period is 12 seconds
obio0 at mainbus0: On-board I/O
grf iomux: old 00000040, new 14001400, renew 00001440
grf iomux: old 00000000, new 04000000, renew 00000000
grf iomux: old 00000000, new 50004000, renew 00004000
grf iomux: old 00000000, new 55551555, renew 00001555
grf iomux: old 00009000, new c0008000, renew 00009000
grf iomux: old 00000028, new 003c0028, renew 00000028
grf iomux: old 00000000, new 30000000, renew 00000000
grf iomux: old 0000180a, new 08000800, renew 0000180a
gpio: 0x00034000 0x00000000 -> 0x00002000
gpio: 0x00034004 0x00000000 -> 0x00002000
gpio: 0x0003c000 0x00000000 -> 0x80000000
gpio: 0x0003c004 0x00000000 -> 0x80000000
gpio: 0x00084000 0x00800000 -> 0x00c00000
gpio: 0x00084004 0x00800000 -> 0x00c00000

com0 at obio0: addr 0x20064000-0x200643ff intr 68 mult 4: ns16550a,working fifo

com0: console
dwctwo0 at obio0: addr 0x10180000-0x101bffff intr 48: USB controller
dwctwo1 at obio0: addr 0x101c0000-0x101fffff intr 49: USB controller
dwcmmc0 at obio0: addr 0x10214000-0x10217fff intr 55: SD/MMC controller
dwcmmc2 at obio0: addr 0x1021c000-0x1021ffff intr 57: SD/MMC controller
rkiic0 at obio0: addr 0x2002c000-0x2002dfff intr 72 port 0: I2C0
iic0 at rkiic0: I2C bus
rkiic1 at obio0: addr 0x2002e000-0x2002ffff intr 73 port 1: I2C1
iic1 at rkiic1: I2C bus
rkiic2 at obio0: addr 0x20054000-0x20057fff intr 74 port 2: I2C2
iic2 at rkiic2: I2C bus
rkiic3 at obio0: addr 0x20058000-0x2005bfff intr 75 port 3: I2C3
iic3 at rkiic3: I2C bus
rkiic4 at obio0: addr 0x2005c000-0x2005ffff intr 84 port 4: I2C4
iic4 at rkiic4: I2C bus
usb0 at dwctwo0: USB revision 2.0
usb1 at dwctwo1: USB revision 2.0
cpu1: 600 MHz Cortex-A9 r4p0 (Cortex V7A core)
cpu1: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu1: 32KB/32B 4-way L1 VIPT Instruction cache
cpu1: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu1: 512KB/32B 16-way write-back-locking-D L2 PIPT Unified cache
vfp1 at cpu1: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
sdmmc0 at dwcmmc0
sdmmc1 at dwcmmc2
uhub0 at usb0: vendor 0000 DWC2 root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1 at usb1: vendor 0000 DWC2 root hub, class 9/0, rev 2.00/1.00, addr 1
sdmmc1: couldn't enable card: 60
ld0 at sdmmc0: <0x02:0x544d:SA04G:0x04:0x9c38c4f0:0x09b>
ld0: 3776 MB, 1917 cyl, 64 head, 63 sec, 512 bytes/sect x 7733248 sectors
ld0: 4-bit width, bus clock 24.000 MHz

uhub2 at uhub1 port 1: Terminus Technology USB 2.0 Hub, class 9/0, rev2.00/1.11, addr 2

uhub2: single transaction translator
umass0 at uhub2 port 1 configuration 1 interface 0
umass0: JMicron USB to ATA/ATAPI bridge, rev 2.00/1.00, addr 3
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <SAMSUNG, HM250HI, 2AC1> disk fixed
sd0: 232 GB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
boot device: <unknown>
root device:
------------------------------------------------------------------------

--
FUKAUMI Naoki

Prev by Date: u-boot for Rockchip
Next by Date: Size issues with kernels?
Previous by Thread: u-boot for Rockchip
Next by Thread: Size issues with kernels?
Indexes:

Home | Main Index | Thread Index | Old Index