Port-arm archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
Re: Dockstar (like SHEEVAPLUG) panics at init with -current after Aug 31, 2012
(2012/12/17 11:47), Andy Ruhl wrote:
> On Sun, Dec 16, 2012 at 1:08 PM, Martin Husemann
> <martin%duskware.de@localhost> wrote:
>> I see the same on GuruPlug.
>
> I set SYMTAB_SPACE to 700000 and I get the same panic. I remember
> having boot issues related to this, but not panics. I think this isn't
> it.
>
> Oh well. I hope it gets fixed. These are cool and cheap little
> machines to play with.
>
> Andy
I got a dockstar and tested with it.
The kernel made from today's -current works:
both diskless and USB disk(sd0).
both conf/SHEEVAPLUG and conf/DREAMPLUG
Could you try the following kernel:
http://www.netbsd.org/~msaitoh/sheeva20121218.ub
environment I'm using:
> CE>> printenv
> baudrate=115200
> loads_echo=0
> rootpath=/mnt/ARM_FS/
> run_diag=yes
> console=console=ttyS0,115200
> CASset=min
> MALLOC_len=1
> ethprime=egiga0
> bootargs_root=root=/dev/mtdblock2 ro
> ethmtu=1500
> usb0Mode=host
> nandEcc=1bit
> ethact=egiga0
> ethaddr=00:10:75:1A:4E:08
> cesvcid=XGWMXFRX8WTTP33Z8L5W5VB5FE
> ceserialno=2GEP0KBB
> ceboardver=REDSTONE:1.0
> "bootcmd=tftpboot=0x2000000 openrd.ub
> bootcmd=tftpboot 0x2000000 dockstar.ub; bootm
> serverip=192.168.1.5
> ipaddr=192.168.1.32
> netmask=255.255.255.0
> stdin=serial
> stdout=serial
> stderr=serial
> mainlineLinux=no
> enaMonExt=no
> enaCpuStream=no
> enaWrAllo=no
> pexMode=RC
> disL2Cache=no
> setL2CacheWT=yes
> disL2Prefetch=yes
> enaICPref=yes
> enaDCPref=yes
> sata_dma_mode=yes
> netbsd_en=no
> vxworks_en=no
> bootdelay=3
> disaMvPnp=no
dmesg (diskless system):
> U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16)
>
> U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60
>
> Soc: 88F6281 A0 (DDR2)
> CPU running @ 1200Mhz L2 running @ 400Mhz
> SysClock = 400Mhz , TClock = 200Mhz
>
> DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
> DRAM CS[0] base 0x00000000 size 128MB
> DRAM Total size 128MB 16bit width
> Flash: 0 kB
> Addresses 8M - 0M are saved for the U-Boot usage.
> Mem malloc Initialization (8M - 7M): Done
> NAND:256 MB
>
> CPU : Marvell Feroceon (Rev 1)
> CLOUD ENGINES BOARD: REDSTONE:1.0
>
> Streaming disabled
> Write allocate disabled
>
>
> USB 0: host mode
> PEX 0: interface detected no Link.
> Net: egiga0 [PRIME], egiga1
> Hit any key to stop autoboot: 0
> Using egiga0 device
> TFTP from server 192.168.1.5; our IP address is 192.168.1.32
> Filename 'dockstar.ub'.
> Load address: 0x2000000
> Loading: #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #####################################
> done
> Bytes transferred = 4845504 (49efc0 hex)
> ## Booting image at 02000000 ...
> Image Name: NetBSD/sheevaplug 6.99.15
> Created: 2012-12-18 12:09:57 UTC
> Image Type: ARM NetBSD Kernel Image (uncompressed)
> Data Size: 4845440 Bytes = 4.6 MB
> Load Address: 00008000
> Entry Point: 00008000
> Verifying Checksum ... OK
> OK
> ## Transferring control to NetBSD stage-2 loader (at address 00008000) ...
>
> NetBSD/evbarm (sheevaplug) booting ...
> USPACE_SVC 1df0
> KSTACK_SIZE 1df0
> [ Kernel symbol table missing! ]
> Loaded initial symtab at 0xc03d9698, strtab at 0xc0413514, # entries 14741
> pmap_postinit: Allocated 35 static L1 descriptor tables
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
> 2006, 2007, 2008, 2009, 2010, 2011, 2012
> The NetBSD Foundation, Inc. All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
>
> NetBSD 6.99.15 (SHEEVAPLUG) #0: Tue Dec 18 21:09:56 JST 2012
>
> msaitoh%tap.execsw.org@localhost:/var/sources/NetBSD-current/src/sys/arch/evbarm/compile/SHEEVAPLUG
> total memory = 128 MB
> avail memory = 120 MB
> cprng kernel: WARNING insufficient entropy at creation.
> mainbus0 (root)
> cpu0 at mainbus0 core 0: Sheeva 88SV131 rev 1 (ARM9E-S core)
> cpu0: DC enabled IC enabled WB enabled EABT branch prediction enabled
> cpu0: 16KB/32B 4-way L1 Instruction cache
> cpu0: 16KB/32B 4-way write-back-locking-C L1 Data cache
> mvsoc0 at mainbus0: Marvell 88F6281 Rev. A0 Kirkwood
> mvsoc0: CPU Clock 1200.000 MHz SysClock 400.000 MHz TClock 200.000 MHz
> mvsoctmr0 at mvsoc0 unit 0 offset 0x20300-0x203ff: Marvell SoC Timer
> mvsocgpp0 at mvsoc0 unit 0 offset 0x10100-0x101ff irq 35: Marvell SoC General
> Purpose I/O Port Interface
> mvsocgpp0: 50 gpio pins
> mvsocgpp0: interrupts 96..103, intr 35
> mvsocgpp0: interrupts 104..111, intr 36
> mvsocgpp0: interrupts 112..119, intr 37
> mvsocgpp0: interrupts 120..127, intr 38
> mvsocgpp0: interrupts 128..135, intr 39
> mvsocgpp0: interrupts 136..143, intr 40
> mvsocgpp0: interrupts 144..151, intr 41
> mvsocgpp0: Data Out: 0xeff00000
> mvsocgpp0: Data Out Enable Control: 0xefffffff
> mvsocgpp0: Data Blink Enable: 0x00000000
> mvsocgpp0: Data In Polarity: 0x00000000
> mvsocgpp0: Data In: 0xeff00080
> mvsocgpp0: Interrupt Cause: 0x00000000
> mvsocgpp0: Interrupt Mask: 0x00000000
> mvsocgpp0: Interrupt Level Mask: 0x00000000
> mvsocgpp0: High Data Out: 0xffffffff
> mvsocgpp0: High Data Out Enable Ctrl: 0xfffc3fff
> mvsocgpp0: High Blink Enable: 0x00004000
> mvsocgpp0: High Data In Polarity: 0x00000000
> mvsocgpp0: High Data In: 0x0003fffd
> mvsocgpp0: High Interrupt Cause: 0x00004000
> mvsocgpp0: High Interrupt Mask: 0x00000000
> mvsocgpp0: High Interrupt Level Mask: 0x00000000
> gpio0 at mvsocgpp0: 50 pins
> mvsocrtc0 at mvsoc0 unit 0 offset 0x10300-0x10317: Marvell SoC Real Time Clock
> com0 at mvsoc0 unit 0 offset 0x12000-0x1201f irq 33: ns16550a, working fifo
> com0: console
> com1 at mvsoc0 unit 1 offset 0x12100-0x1211f irq 34: ns16550a, working fifo
> ehci0 at mvsoc0 unit 0 offset 0x50000-0x51fff irq 19: Marvell USB 2.0
> Interface
> usb0 at ehci0: USB revision 2.0
> gtidmac0 at mvsoc0 unit 0 offset 0x60000-0x60fff: Marvell IDMA Controller/XOR
> Engine
> gtidmac0: XOR Engine 4 channels, intr 5...8
> gttwsi0 at mvsoc0 unit 0 offset 0x11000-0x110ff irq 29: Marvell TWSI
> controller
> iic0 at gttwsi0: I2C bus
> mvcesa0 at mvsoc0 unit 0 offset 0x30000-0x3ffff irq 22: Marvell Cryptographic
> Engines and Security Accelerator
> mvgbec0 at mvsoc0 unit 0 offset 0x70000-0x73fff: Marvell Gigabit Ethernet
> Controller
> mvgbe0 at mvgbec0 port 0 irq 11
> mvgbe0: Ethernet address 00:10:75:1a:4e:08
> makphy0 at mvgbe0 phy 0: Marvell 88E1116R Gigabit PHY, rev. 0
> makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
> 1000baseT-FDX, auto
> mvgbec1 at mvsoc0 unit 1 offset 0x74000-0x77fff: Marvell Gigabit Ethernet
> Controller
> mvgbe at mvgbec1 port 0 not configured
> mvpex0 at mvsoc0 unit 0 offset 0x40000-0x41fff irq 9: Marvell PCI Express
> Interface
> pci0 at mvpex0
> vendor 0x11ab product 0x6281 (miscellaneous memory, revision 0x02) at pci0
> dev 0 function 0 not configured
> mvsoc0: mvsata0 clock disabled
> mvsdio0 at mvsoc0 unit 0 offset 0x90000-0x9ffff irq 28: Marvell Secure
> Digital Input/Output Interface
> sdmmc0 at mvsdio0
> uhub0 at usb0: Marvell EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub1 at uhub0 port 1: Genesys Logic USB2.0 Hub, class 9/0, rev 2.00/6.03,
> addr 2
> uhub1: single transaction translator
> cprng sysctl: WARNING insufficient entropy at creation.
> boot device: <unknown>
> root device: mvgbe0
> dump device:
> file system (default generic): nfs
> root on mvgbe0
> nfs_boot: trying DHCP/BOOTP
> [mvgbe0 LSC D]
> [mvgbe0 LSC U]
> nfs_boot: DHCP next-server: 192.168.1.5
> nfs_boot: my_domain=execsw.org
> nfs_boot: my_addr=192.168.1.32
> nfs_boot: my_mask=255.255.255.0
> nfs_boot: gateway=192.168.1.1
> root on 192.168.1.5:/var/diskless/evbarm-current/root
> root time: 0x50d05d5c
> WARNING: clock lost 4735 days
> WARNING: using filesystem time
> WARNING: CHECK AND RESET THE DATE!
> init path (default /sbin/init):
> init: copying out path `/sbin/init' 11
> Tue Dec 18 21:11:08 JST 2012
> Not checking /: fs_passno = 0 in /etc/fstab
> Starting file system checks:
> Setting tty flags.
> Setting sysctl variables:
> ddb.onpanic: 1 -> 0
> Starting network.
> Hostname: dockstar.execsw.org
> IPv6 mode: autoconfigured host
> Configuring network interfaces: mvgbe0[mvgbe0 LSC U]
> .
> Adding interface aliases:.
> add net default: gateway 192.168.1.1
> Starting route6d.
> Building databases: dev, utmp, utmpx.
> Trimming log files: done.
> Starting syslogd.
> cprng 154408d23: WARNING insufficient entropy at creation.
> Setting date via ntp.
> Starting rpcbind.
> Mounting all filesystems...
> Clearing temporary files.
> Creating a.out runtime link editor directory cache.
> Checking quotas: done.
> /etc/rc: WARNING: /etc/exports is not readable.
> /etc/rc.d/mountd exited with code 1
> Starting nfsd.
> Setting securelevel: kern.securelevel: 0 -> 1
> swapctl: adding 192.168.1.5:/var/diskless/evbarm-current/swapfile as swap
> device at priority 0
> Starting virecover.
> Checking for core dump...
> savecore: no core dump (no dumpdev)
> Starting local daemons:.
> Updating motd.
> Starting ntpd.
> Starting sshd.
> cprng 350118d9: WARNING insufficient entropy at creation.
> Starting inetd.
> Starting cron.
> The following components reported failures:
> /etc/rc.d/mountd
> See /var/run/rc.log for more information.
> Tue Dec 18 21:11:39 JST 2012
>
> NetBSD/evbarm (dockstar.execsw.org) (console)
>
> login: root
> Password:
> Dec 18 21:11:58 dockstar login: ROOT LOGIN (root) on tty console
> Last login: Wed Oct 24 03:15:34 2012 on console
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
> 2006, 2007, 2008, 2009, 2010, 2011, 2012
> The NetBSD Foundation, Inc. All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
>
> NetBSD 6.99.15 (SHEEVAPLUG) #0: Tue Dec 18 21:09:56 JST 2012
>
> Welcome to NetBSD!
>
> You have mail.
> Terminal type is vt100.
> We recommend that you create a non-root account and use su(1) for root access.
> dockstar# sync
> dockstar# shutdown -r now
> Shutdown NOW!
> shutdown: [pid 496]
> dockstar# wall: You have write permission turned off; no reply possible
>
> *** FINAL System shutdown message from root%dockstar.execsw.org@localhost ***
> System going down IMMEDIATELY
>
>
> Dec 18 21:12:08 dockstar shutdown: reboot by root:
>
> System shutdown time has arrived
>
> About to run shutdown hooks...
> Stopping cron.
> Waiting for PIDS: 503.
> Stopping inetd.
> Waiting for PIDS: 541.
> Removing block-type swap devices
> Tue Dec 18 21:12:15 JST 2012
> umass0 at uhub1 port 3 configuration 1 interface 0
> umass0: BUFFALO USB Flash Disk, rev 2.00/40.00, addr 3
> scsibus0 at umass0: 2 targets, 1 lun per target
> sd0 at scsibus0 target 0 lun 0: <BUFFALO, USB Flash Disk, 4000> disk removable
> sd0: 7648 MB, 15744 cyl, 16 head, 63 sec, 512 bytes/sect x 15663104 sectors
>
> Done running shutdown hooks.
> Dec 18 21:12:20 dockstar syslogd[155]: Exiting on signal 15
> syncing disks... done
> unmounting file systems...
> unmounting 0xc27ac008 /swap
> (192.168.1.5:/var/diskless/evbarm-current/swapfile)...
> unmounting 0xc27a9008 /var/sources (192.168.1.15:/var/sources)...
> unmounting 0xc27a7008 /home (192.168.1.2:/disk/home)...
> unmounting 0xc27a6008 /proc (procfs)...
> unmounting 0xc27a5008 /kern (kernfs)...
> unmounting 0xc268d008 /dev/pts (ptyfs)...
> unmounting 0xc25e3008 / (192.168.1.5:/var/diskless/evbarm-current/root)...
> unmounting done
> rebooting...
dmesg (USB sd0):
> U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16)
>
> U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60
>
> Soc: 88F6281 A0 (DDR2)
> CPU running @ 1200Mhz L2 running @ 400Mhz
> SysClock = 400Mhz , TClock = 200Mhz
>
> DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
> DRAM CS[0] base 0x00000000 size 128MB
> DRAM Total size 128MB 16bit width
> Flash: 0 kB
> Addresses 8M - 0M are saved for the U-Boot usage.
> Mem malloc Initialization (8M - 7M): Done
> NAND:256 MB
>
> CPU : Marvell Feroceon (Rev 1)
> CLOUD ENGINES BOARD: REDSTONE:1.0
>
> Streaming disabled
> Write allocate disabled
>
>
> USB 0: host mode
> PEX 0: interface detected no Link.
> Net: egiga0 [PRIME], egiga1
> Hit any key to stop autoboot: 0
> Using egiga0 device
> TFTP from server 192.168.1.5; our IP address is 192.168.1.32
> Filename 'dockstar.ub'.
> Load address: 0x2000000
> Loading: #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #####################################
> done
> Bytes transferred = 4845504 (49efc0 hex)
> ## Booting image at 02000000 ...
> Image Name: NetBSD/sheevaplug 6.99.15
> Created: 2012-12-18 12:09:57 UTC
> Image Type: ARM NetBSD Kernel Image (uncompressed)
> Data Size: 4845440 Bytes = 4.6 MB
> Load Address: 00008000
> Entry Point: 00008000
> Verifying Checksum ... OK
> OK
> ## Transferring control to NetBSD stage-2 loader (at address 00008000) ...
>
> NetBSD/evbarm (sheevaplug) booting ...
> USPACE_SVC 1df0
> KSTACK_SIZE 1df0
> [ Kernel symbol table missing! ]
> Loaded initial symtab at 0xc03d9698, strtab at 0xc0413514, # entries 14741
> pmap_postinit: Allocated 35 static L1 descriptor tables
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
> 2006, 2007, 2008, 2009, 2010, 2011, 2012
> The NetBSD Foundation, Inc. All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
>
> NetBSD 6.99.15 (SHEEVAPLUG) #0: Tue Dec 18 21:09:56 JST 2012
>
> msaitoh%tap.execsw.org@localhost:/var/sources/NetBSD-current/src/sys/arch/evbarm/compile/SHEEVAPLUG
> total memory = 128 MB
> avail memory = 120 MB
> cprng kernel: WARNING insufficient entropy at creation.
> mainbus0 (root)
> cpu0 at mainbus0 core 0: Sheeva 88SV131 rev 1 (ARM9E-S core)
> cpu0: DC enabled IC enabled WB enabled EABT branch prediction enabled
> cpu0: 16KB/32B 4-way L1 Instruction cache
> cpu0: 16KB/32B 4-way write-back-locking-C L1 Data cache
> mvsoc0 at mainbus0: Marvell 88F6281 Rev. A0 Kirkwood
> mvsoc0: CPU Clock 1200.000 MHz SysClock 400.000 MHz TClock 200.000 MHz
> mvsoctmr0 at mvsoc0 unit 0 offset 0x20300-0x203ff: Marvell SoC Timer
> mvsocgpp0 at mvsoc0 unit 0 offset 0x10100-0x101ff irq 35: Marvell SoC General
> Purpose I/O Port Interface
> mvsocgpp0: 50 gpio pins
> mvsocgpp0: interrupts 96..103, intr 35
> mvsocgpp0: interrupts 104..111, intr 36
> mvsocgpp0: interrupts 112..119, intr 37
> mvsocgpp0: interrupts 120..127, intr 38
> mvsocgpp0: interrupts 128..135, intr 39
> mvsocgpp0: interrupts 136..143, intr 40
> mvsocgpp0: interrupts 144..151, intr 41
> mvsocgpp0: Data Out: 0xeff00000
> mvsocgpp0: Data Out Enable Control: 0xefffffff
> mvsocgpp0: Data Blink Enable: 0x00000000
> mvsocgpp0: Data In Polarity: 0x00000000
> mvsocgpp0: Data In: 0xeff00080
> mvsocgpp0: Interrupt Cause: 0x00000000
> mvsocgpp0: Interrupt Mask: 0x00000000
> mvsocgpp0: Interrupt Level Mask: 0x00000000
> mvsocgpp0: High Data Out: 0xffffffff
> mvsocgpp0: High Data Out Enable Ctrl: 0xfffc3fff
> mvsocgpp0: High Blink Enable: 0x00004000
> mvsocgpp0: High Data In Polarity: 0x00000000
> mvsocgpp0: High Data In: 0x0003fffd
> mvsocgpp0: High Interrupt Cause: 0x00004000
> mvsocgpp0: High Interrupt Mask: 0x00000000
> mvsocgpp0: High Interrupt Level Mask: 0x00000000
> gpio0 at mvsocgpp0: 50 pins
> mvsocrtc0 at mvsoc0 unit 0 offset 0x10300-0x10317: Marvell SoC Real Time Clock
> com0 at mvsoc0 unit 0 offset 0x12000-0x1201f irq 33: ns16550a, working fifo
> com0: console
> com1 at mvsoc0 unit 1 offset 0x12100-0x1211f irq 34: ns16550a, working fifo
> ehci0 at mvsoc0 unit 0 offset 0x50000-0x51fff irq 19: Marvell USB 2.0
> Interface
> usb0 at ehci0: USB revision 2.0
> gtidmac0 at mvsoc0 unit 0 offset 0x60000-0x60fff: Marvell IDMA Controller/XOR
> Engine
> gtidmac0: XOR Engine 4 channels, intr 5...8
> gttwsi0 at mvsoc0 unit 0 offset 0x11000-0x110ff irq 29: Marvell TWSI
> controller
> iic0 at gttwsi0: I2C bus
> mvcesa0 at mvsoc0 unit 0 offset 0x30000-0x3ffff irq 22: Marvell Cryptographic
> Engines and Security Accelerator
> mvgbec0 at mvsoc0 unit 0 offset 0x70000-0x73fff: Marvell Gigabit Ethernet
> Controller
> mvgbe0 at mvgbec0 port 0 irq 11
> mvgbe0: Ethernet address 00:10:75:1a:4e:08
> makphy0 at mvgbe0 phy 0: Marvell 88E1116R Gigabit PHY, rev. 0
> makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
> 1000baseT-FDX, auto
> mvgbec1 at mvsoc0 unit 1 offset 0x74000-0x77fff: Marvell Gigabit Ethernet
> Controller
> mvgbe at mvgbec1 port 0 not configured
> mvpex0 at mvsoc0 unit 0 offset 0x40000-0x41fff irq 9: Marvell PCI Express
> Interface
> pci0 at mvpex0
> vendor 0x11ab product 0x6281 (miscellaneous memory, revision 0x02) at pci0
> dev 0 function 0 not configured
> mvsoc0: mvsata0 clock disabled
> mvsdio0 at mvsoc0 unit 0 offset 0x90000-0x9ffff irq 28: Marvell Secure
> Digital Input/Output Interface
> sdmmc0 at mvsdio0
> uhub0 at usb0: Marvell EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub1 at uhub0 port 1: Genesys Logic USB2.0 Hub, class 9/0, rev 2.00/6.03,
> addr 2
> uhub1: single transaction translator
> umass0 at uhub1 port 3 configuration 1 interface 0
> umass0: BUFFALO USB Flash Disk, rev 2.00/40.00, addr 3
> scsibus0 at umass0: 2 targets, 1 lun per target
> sd0 at scsibus0 target 0 lun 0: <BUFFALO, USB Flash Disk, 4000> disk removable
> sd0: 7648 MB, 15744 cyl, 16 head, 63 sec, 512 bytes/sect x 15663104 sectors
> cprng sysctl: WARNING insufficient entropy at creation.
> boot device: <unknown>
> root device: sd0a
> dump device (default sd0b):
> file system (default generic): ffs
> root on sd0a dumps on sd0b
> WARNING: clock lost 4686 days
> WARNING: using filesystem time
> WARNING: CHECK AND RESET THE DATE!
> init path (default /sbin/init):
> init: copying out path `/sbin/init' 11
> Tue Oct 30 21:08:33 JST 2012
> Starting root file system check:
> /dev/rsd0a: file system is clean; not checking
> swapctl: setting dump device to /dev/sd0b
> swapctl: adding /dev/sd0b as swap device at priority 0
> Starting file system checks:
> Setting tty flags.
> Setting sysctl variables:
> ddb.onpanic: 1 -> 0
> Starting network.
> Hostname: sheeva.execsw.org
> IPv6 mode: host
> Configuring network interfaces: mvgbe0
> cprng sysctl: WARNING pseudorandom rekeying.
> .
> Adding interface aliases:.
> Building databases: dev, utmp, utmpx.
> Starting syslogd.
> Setting date via ntp.
> Mounting all filesystems...
> Clearing temporary files.
> Creating a.out runtime link editor directory cache.
> Checking quotas: done.
> Loaded entropy from disk.
> Setting securelevel: kern.securelevel: 0 -> 1
> swapctl: setting dump device to /dev/sd0b
> Starting virecover.
> Checking for core dump...
> savecore: no core dump
> Starting local daemons:.
> Updating motd.
> Starting ntpd.
> Starting sshd.
> Starting inetd.
> Starting cron.
> Tue Dec 18 21:14:12 JST 2012
>
> NetBSD/evbarm (dockstar.execsw.org) (console)
>
--
-----------------------------------------------
SAITOH Masanobu (msaitoh%execsw.org@localhost
msaitoh%netbsd.org@localhost)
Home |
Main Index |
Thread Index |
Old Index