I created a 3.99 install kernel for an IQ80321 based board and can manage
to get all the way through the kernel load where it halts after "WARNING:
CHECK AND RESET THE DATE!"  Granted I get a lot of errors from the SCSI
controller, should probably disable the driver.

This is the first time I've ever tried getting a different board up and
running.  Any clues I should look for?

thanks

diana


Ethernet eth0: MAC address 00:0e:a4:00:17:d6
IP: 192.168.0.250/255.255.255.0, Gateway: 192.168.0.1
Default server: 192.168.0.1, DNS server IP: 192.168.0.1

RedBoot(tm) bootstrap and debug environment DPA3V2 - built 15:27:54, Feb  6 2004

Platform: IQ80321 (XScale)
Copyright (C) 2000, 2001, 2002, Red Hat, Inc.

RAM: 0x00000000-0x10000000, 0x0001ae70-0x0ffd1000 available
FLASH: 0xf0000000 - 0xf1000000, 128 blocks of 0x00020000 bytes each.
== Executing boot script in 3.000 seconds - enter ^C to abort
^C
RedBoot> load netbsd-THINGY_INSTALL.srec
Using default protocol (TFTP)
Entry point: 0x00200000, address range: 0x00200000-0x007993f4
RedBoot> go
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 3.99.14 (THINGY_INSTALL) #1: Wed Dec 21 15:36:35 MST 2005

deichert@wrench.com:/home/dee/NetBSD/src/sys/arch/evbarm/compile/obj/THINGY_INSTALL
total memory = 256 MB
avail memory = 242 MB
mainbus0 (root)
cpu0 at mainbus0: i80321 600MHz rev 2 (XScale core)
cpu0: DC enabled IC enabled WB enabled LABT branch prediction enabled
cpu0: 32KB/32B 32-way Instruction cache
cpu0: 32KB/32B 32-way write-back-locking Data cache
obio0 at mainbus0
com0 at obio0 addr 0xfe800000 xint 1: ns16550a, working fifo
com0: console
iopxs0 at mainbus0: i80321 I/O Processor, acting as PCI host
iopxs0: configuring PCI bus
iopaau0 at iopxs0
iopiic0 at iopxs0: I2C controller
iic0 at iopiic0: I2C bus
iopiic1 at iopxs0: I2C controller
iic1 at iopiic1: I2C bus
iopwdog0 at iopxs0: 7 second period
pci0 at iopxs0 bus 0
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
wm0 at pci0 dev 0 function 0: Intel i82546EB 1000BASE-T Ethernet, rev. 1
wm0: interrupting at irq 27
wm0: Ethernet address 00:0e:a4:00:17:d6
makphy0 at wm0 phy 1: Marvell 88E1011 Gigabit PHY, rev. 3
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
wm1 at pci0 dev 0 function 1: Intel i82546EB 1000BASE-T Ethernet, rev. 1
wm1: interrupting at irq 27
wm1: Ethernet address 00:0e:a4:00:17:d7
makphy1 at wm1 phy 1: Marvell 88E1011 Gigabit PHY, rev. 3
makphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
artsata0 at pci0 dev 1 function 0
artsata0: Intel 31244 Serial ATA Controller (rev. 0x00)
artsata0: bus-master DMA support present
artsata0: primary channel wired to native-PCI mode
artsata0: using irq 29 for native-PCI interrupt
atabus0 at artsata0 channel 0
artsata0: secondary channel wired to native-PCI mode
atabus1 at artsata0 channel 1
esiop0 at pci0 dev 2 function 0: Symbios Logic 53c1010-66 (ultra3-wide scsi)
esiop0: using on-board RAM
esiop0: interrupting at irq 30
esiop0: switching to single-ended mode
esiop0: DMA IRQ: bus fault DMA fifo empty, DSP=0x7ffbfff8 DSA=0x0:
current T/L/Q invalid
esiop0: scsi bus reset
scsibus0 at esiop0: 16 targets, 8 luns per target
Symbios Logic 53c1010 (66MHz) (SCSI mass storage, revision 0x01) at pci0
dev 2 function 1 not configured
clock: hz=100 stathz=0 profhz=0
md0: internal 3075 KB image area
scsibus0: waiting 2 seconds for devices to settle...
wd0 at atabus0 drive 0: <ST3160023AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 149 GB, 310101 cyl, 16 head, 63 sec, 512 bytes/sect x 312581808 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(artsata0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd1 at atabus1 drive 0: <ST3160023AS>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 149 GB, 310101 cyl, 16 head, 63 sec, 512 bytes/sect x 312581808 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd1(artsata0:1:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
probe(esiop0:0:0:0): request sense for a request sense ?
probe(esiop0:0:0:0): request sense failed with error 22
esiop_cmd (target 0 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 0 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:0:0): generic HBA error
probe(esiop0:0:1:0): request sense for a request sense ?
probe(esiop0:0:1:0): request sense failed with error 22
esiop_cmd (target 1 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 1 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:1:0): generic HBA error
probe(esiop0:0:2:0): request sense for a request sense ?
probe(esiop0:0:2:0): request sense failed with error 22
esiop_cmd (target 2 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 2 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:2:0): generic HBA error
probe(esiop0:0:3:0): request sense for a request sense ?
probe(esiop0:0:3:0): request sense failed with error 22
esiop_cmd (target 3 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 3 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:3:0): generic HBA error
probe(esiop0:0:4:0): request sense for a request sense ?
probe(esiop0:0:4:0): request sense failed with error 22
esiop_cmd (target 4 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 4 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:4:0): generic HBA error
probe(esiop0:0:5:0): request sense for a request sense ?
probe(esiop0:0:5:0): request sense failed with error 22
esiop_cmd (target 5 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 5 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:5:0): generic HBA error
probe(esiop0:0:6:0): request sense for a request sense ?
probe(esiop0:0:6:0): request sense failed with error 22
esiop_cmd (target 6 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 6 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:6:0): generic HBA error
probe(esiop0:0:8:0): request sense for a request sense ?
probe(esiop0:0:8:0): request sense failed with error 22
esiop_cmd (target 8 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 8 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:8:0): generic HBA error
probe(esiop0:0:9:0): request sense for a request sense ?
probe(esiop0:0:9:0): request sense failed with error 22
esiop_cmd (target 9 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 9 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:9:0): generic HBA error
probe(esiop0:0:10:0): request sense for a request sense ?
probe(esiop0:0:10:0): request sense failed with error 22
esiop_cmd (target 10 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 10 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:10:0): generic HBA error
probe(esiop0:0:11:0): request sense for a request sense ?
probe(esiop0:0:11:0): request sense failed with error 22
esiop_cmd (target 11 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 11 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:11:0): generic HBA error
probe(esiop0:0:12:0): request sense for a request sense ?
probe(esiop0:0:12:0): request sense failed with error 22
esiop_cmd (target 12 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 12 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:12:0): generic HBA error
probe(esiop0:0:13:0): request sense for a request sense ?
probe(esiop0:0:13:0): request sense failed with error 22
esiop_cmd (target 13 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 13 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:13:0): generic HBA error
probe(esiop0:0:14:0): request sense for a request sense ?
probe(esiop0:0:14:0): request sense failed with error 22
esiop_cmd (target 14 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 14 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:14:0): generic HBA error
probe(esiop0:0:15:0): request sense for a request sense ?
probe(esiop0:0:15:0): request sense failed with error 22
esiop_cmd (target 15 lun 0 tag -1) not valid
esiop0: unexpected disconnect without command
esiop_cmd (target 15 lun 0 tag -1) not valid
esiop0: scsi bus reset
probe(esiop0:0:15:0): generic HBA error
boot device: <unknown>
root on md0a dumps on md0b
root file system type: ffs
WARNING: CHECK AND RESET THE DATE!