At 09:53 PM 3/24/2001 -0800, bob meader wrote:


>Matt Thomas wrote:
>It boots fine off the CD but hangs probing scsibus0.
>
> > (off jazzsiop0).  I have no devices hanging off it;
> > everything is off scsibus1.
>
>My output from my RISCServer 2200 (remember there
>is also a model RISCServer Express 2200..which do you
>have ?) is listed below..
>Where done it fail on your unit?

It's a RiscServer 2200.

Before the memory it prints: R-96

>cpu0 at mainbus0: MIPS R4400 CPU (0x460) Rev. 6.0 with MIPS R4010 FPC Rev. 0.0
>cpu0: L1 cache: 16KB/32B instruction, 16KB/32B data, direct mapped
>cpu0: L2 cache: 2048KB/64B mixed, no snooping
>jazzio0 at mainbus0
>aclock0 at jazzio0 addr 0xe0004000 intr 0: mc146818 or compatible
>lpt0 at jazzio0 addr 0xe0008000 intr 1
>fdc0 at jazzio0 addr 0xe000c000 intr 2
>fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec

I don't have a floppy so no fd0.

>sn0 at jazzio0 addr 0xe0001000 intr 4: bufsize 28480 address 00:00:4c:75:2d:2a
>arcsiop0 at jazzio0 addr 0xe0002000 intr 5: SCSI ID 7
>arcsiop1 at jazzio0 addr 0xe0003000 intr 6: SCSI ID 7
>scsibus1 at arcsiop1: 8 targets, 8 luns per target
>pckbc0 at jazzio0 addr 0xe0005000 intr 7
>pckbd0 at pckbc0 (kbd slot)
>wskbd0 at pckbd0: console keyboard
>pms0 at pckbc0 (aux slot)
>wsmouse0 at pms0 mux 0

No mouse attached either.

>pms at jazzio0 addr 0xe0005000 intr 8 not configured
>com0 at jazzio0 addr 0xe0006000 intr 9: ns16550a, working fifo
>com0: txfifo disabled
>com1 at jazzio0 addr 0xe0007000 intr 10: ns16550a, working fifo
>com1: txfifo disabled
>isabr0 at mainbus0
>isa0 at isabr0 isa_io_base 0xe2000000 isa_mem_base 0xe3000000

Don't have one of these:

>wdc0 at isa0 port 0x1f0-0x1f7 irq 14
>wd0 at wdc0 channel 0 drive 0: <WDC AC11200L>
>wd0: drive supports 16-sector PIO transfers, LBA addressing
>wd0: 1222 MB, 2484 cyl, 16 head, 63 sec, 512 bytes/sect x 2503872 sectors
>wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)



>vga0 at isa0 port 0x3b0-0x3df iomem 0xa0000-0xbffff
>wsdisplay0 at vga0: console (80x25, vt100 emulation), using wskbd0
>scsibus0: waiting 2 seconds for devices to settle...

It never gets passed the above line.

--
Matt Thomas               Internet:   matt@3am-software.com
3am Software Foundry      WWW URL:    http://www.3am-software.com/bio/matt/
Cupertino, CA             Disclaimer: I avow all knowledge of this message