Problems with IOblix serial ports

[John Klos <john%klos.com@localhost>]

Hi,

I just got an IOblix four port serial and two port parallel card for my 
Amiga, but I get a panic when I try to send the first character. I run cu, 
press a key on the keyboard, and get:

uvm_fault(0x334350, 0x1518000, 0x1) -> 0xe
  type 8, code [mmu,,ssw]: 1468200
trap type 8, code = 1468200, v = 1518000
pid = 520, lid = 1, pc = 01518000, ps = 2700, sfc = 1, dfc = 1
Registers:
             0        1        2        3        4        5        6        7
dreg: 01518000 00000001 00000004 00000001 00006E7A 000033D4 00000000 00000000
areg: 01518000 0024AF20 00006C4A 0000699C 0000326C 0000335C 0BF8DC44 0DFFE7E0

Kernel stack (0BF8DACC):
F8DACC: 0029CF12 0BF8DBE0 00000080 0BF8DB50 0029D462 00000008 01468200 01518000
F8DAEC: 0BF8DBE0 0BD90070 00000000 00000000 00000000 00000000 00000001 00000000
F8DB0C: 00000000 00000000 00000001 00000000 00000000 00000008 00000000 00000000
F8DB2C: 00000000 00000000 0CA1D680 09DA4C40 00000001 01518000 00334350 0000000E
F8DB4C: 00000003 0BF8DBC8 0029DAEC 00000008 01468200 01518000 0BF8DBE0 0BED27E0
F8DB6C: 00000000 00000000 08216000 00000000 0000013A 0BED07E0 00000001 00000000
F8DB8C: 00000000 00000000 00000000 00000000 00000000 00000008 00000000 00000000
F8DBAC: 00000000 00000000 0BED27E0 0CA1D680 00000000 00000000 00000000 0BF8DC44
F8DBCC: 00002060 0BF8DBE0 00000008 01468200 01518000 01518000 00000001 00000004
F8DBEC: 00000001 00006E7A 000033D4 00000000 00000000 01518000 0024AF20 00006C4A
F8DC0C: 0000699C 0000326C 0000335C 0BF8DC44 0DFFE7E0 00000000 27000151 80004008
F8DC2C: 01518000 01468200 002675C8 09D70D80 09D70D80 00000000 0BF8DC70 00002378
F8DC4C: 09D70D80 09D70DD4 00002410 00002700 003484B8 0024AF98 24100009 1CF60078
F8DC6C: 00002000 0BF8DC9C 00093628 00002410 00000000 00000001 0B0A2F18 0B0A2F50
F8DC8C: 00002410 00CB5400 00000001 00000001 0BF8DCA8 001DA73E 0B0A30C0 0BF8DD40
F8DCAC: 001DB698 0B0A30C0 0000000C 00000001 00000000 0D000000 0820C000 0BF8A000
panic: MMU fault
Begin traceback...
?(?)
panic(2ec86a,bf8db50,29d462,8,1468200) at 0
panictrap(8,1468200,1518000,bf8dbe0) + 72
trapmmufault(8,1468200,1518000,bf8dbe0,bed27e0,0,0) + 4a6
trap(bf8dbe0,8,1468200,1518000) + 5ba
_prop_dictionary_keysym32_pool(9d70d80) + 11cec98
lev6intr(?)
_spl(2410) + 74
comstart(b0a30c0) + 23a
ttstart(b0a30c0) + 1c
ttwrite(b0a30c0,bf8de80,10) + 45e
comwrite(2000,bf8de80,10) + 9c
cdev_write(2000,bf8de80,10) + 4c
spec_write(bf8de0c) + 76
ufsspec_write(bf8de0c) + 66
VOP_WRITE(bee6338,bf8de80,10,9d898fc) + 56
vn_write(b981b40,b981b40,bf8de80,9d898fc,1) + 114
dofilewrite(3,b981b40,dffe833,1,b981b40,1,bf8df18) + 7e
sys_write(bed27e0,bf8df20,bf8df18) + 7e
sy_call(2f990c,bed27e0,bf8df20,bf8df18) + 22
syscall_plain(4,bed27e0,bf8dfb4) + 112
syscall(4) + 11c
trap0() + e
End traceback...

I tried this with a GENERIC NetBSD 5 kernel, too, and there was no 
change, and I also made sure I had IOBZCLOCK=24000000 in my kernel config 
because I have an older board.

Any ideas? Is anyone else using an IOblix nowadays?

Thanks,
John Klos