Re: ACPI call for testing (take two)

[Jasper Wallace <jasper%pointless.net@localhost>]

On Fri, 7 Jan 2011, Jukka Ruohonen wrote:

> On Fri, Jan 07, 2011 at 11:56:32AM +0200, Jukka Ruohonen wrote:
> > Please try the attached patch on as many x86 systems as is possible.
> 
> For convenience, I made also the following 5.99.43 kernels:
> 
>       ftp://ftp.NetBSD.org/pub/NetBSD/misc/jruoho/GENERIC-amd64
>       ftp://ftp.NetBSD.org/pub/NetBSD/misc/jruoho/MONOLITHIC-i386

With the amd64 kernel on a Tyan S3992 motherboard with a pair of amd 
2212's i get constant interupts on ioapic0 pin 9.

unfortunatly boot with -v -x dosn't dump the interrupt routing like it 
does on i386, so i don't know how much help dmesg is, it's attached 
anyway.

-- 
[http://pointless.net/]                                   [0x2ECA0975]

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.43 (GENERIC) #0: Fri Jan  7 13:49:49 EET 2011
        jruoho%camus.bitnet@localhost:/tmp/obj/sys/arch/amd64/compile/GENERIC
total memory = 4095 MB
avail memory = 3954 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
SMBIOS rev. 2.3 @ 0xf9770 (61 entries)
empty empty (empty)
mainbus0 (root)
cpu0 at mainbus0 apid 0cpu0: 16 page colors
cpu0: calibrating local timer
cpu0: apic clock running at 199 MHz
: AMD 686-class, 1995MHz, id 0x40f12
cpu0: PAT enabled
cpu1 at mainbus0 apid 1x86_ipi_init: ESR 00000004
: AMD 686-class, 1995MHz, id 0x40f12
cpu1: PAT enabled
cpu2 at mainbus0 apid 2: AMD 686-class, 1995MHz, id 0x40f12
cpu2: PAT enabled
cpu3 at mainbus0 apid 3: AMD 686-class, 1995MHz, id 0x40f12
cpu3: PAT enabled
ioapic0 at mainbus0 apid 4: pa 0xfec00000, version 11, 16 pins
ioapic1 at mainbus0 apid 5: pa 0xfec01000, version 11, 16 pins
ioapic2 at mainbus0 apid 6: pa 0xfec02000, version 11, 16 pins
acpi0 at mainbus0: Intel ACPICA 20100528
acpi0: X/RSDT: OemId <A M I ,OEMXSDT ,09000620>, AslId <MSFT,00000097>
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
acpi0: ACPI-Safe 32-bit timer
acpi0: warning: timer may be unreliable
P001 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
P002 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
P003 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
P004 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
UAR1 (PNP0501) at acpi0 not configured
UAR2 (PNP0501) at acpi0 not configured
RMSC (PNP0C02) at acpi0 not configured
OMSC (PNP0C02) at acpi0 not configured
pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
SIOR (PNP0C02) at acpi0 not configured
PCIE (PNP0C02) at acpi0 not configured
RMEM (PNP0C01) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
acpi0: fixed power button present
acpi0: fixed power button present
acpi0: SCI interrupting at int 9
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pmsprobe: reset error 5
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
ppb0 at pci0 dev 1 function 0: vendor 0x1166 product 0x0036 (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
ppb1 at pci1 dev 13 function 0: vendor 0x1166 product 0x0104 (rev. 0xc0)
pci2 at ppb1 bus 2
pci2: memory space enabled
svwsata0 at pci1 dev 14 function 0: ServerWorks HT-1000 SATA Controller (rev. 
0x00)
svwsata0: bus-master DMA support present
svwsata0: using ioapic0 pin 11 for native-PCI interrupt
svwsata0: primary channel wired to native-PCI mode
atabus0 at svwsata0 channel 0
svwsata0: secondary channel wired to native-PCI mode
atabus1 at svwsata0 channel 1
svwsata0: secondary channel wired to compatibility mode
atabus2 at svwsata0 channel 2
svwsata0: secondary channel configured to compatibility mode
atabus3 at svwsata0 channel 3
svwsata0: WARNING: power management not supported
piixpm0 at pci0 dev 2 function 0
piixpm0: vendor 0x1166 product 0x0205 (rev. 0x00)
piixpm0: polling
iic0 at piixpm0: I2C bus
pciide0 at pci0 dev 2 function 1: vendor 0x1166 product 0x0214 (rev. 0x00)
pciide0: bus-master DMA support present, but unused (no driver support)
pciide0: primary channel configured to compatibility mode
pciide0: primary channel interrupting at ioapic0 pin 14
atabus4 at pciide0 channel 0
pciide0: secondary channel configured to compatibility mode
pciide0: secondary channel ignored (not responding; disabled or no drives?)
pciide0: WARNING: power management not supported
pcib0 at pci0 dev 2 function 2: vendor 0x1166 product 0x0234 (rev. 0x00)
ohci0 at pci0 dev 3 function 0: vendor 0x1166 product 0x0223 (rev. 0x01)
ohci0: interrupting at ioapic0 pin 10
ohci0: OHCI version 1.0, legacy support
ohci0: SMM does not respond, resetting
usb0 at ohci0: USB revision 1.0
usb0: WARNING: power management not supported
ohci1 at pci0 dev 3 function 1: vendor 0x1166 product 0x0223 (rev. 0x01)
ohci1: interrupting at ioapic0 pin 10
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
usb1: WARNING: power management not supported
ehci0 at pci0 dev 3 function 2: vendor 0x1166 product 0x0223 (rev. 0x01)
ehci0: interrupting at ioapic0 pin 10
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
usb2: WARNING: power management not supported
fxp0 at pci0 dev 4 function 0: i82551 Ethernet, rev 16
fxp0: interrupting at ioapic1 pin 0
fxp0: Ethernet address 00:e0:81:47:b1:31
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ppb2 at pci0 dev 6 function 0: vendor 0x1166 product 0x0130 (rev. 0xa3)
pci3 at ppb2 bus 3
pci3: memory space enabled
ppb3 at pci0 dev 7 function 0: vendor 0x1166 product 0x0130 (rev. 0xa3)
pci4 at ppb3 bus 4
pci4: memory space enabled
bge0 at pci4 dev 4 function 0: Broadcom BCM5780 Gigabit Ethernet
bge0: interrupting at ioapic1 pin 10
bge0: ASIC BCM5714 B3 (0x8003), Ethernet address 00:e0:81:47:b0:f4
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM5780 1000BASE-T media interface, rev. 0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
bge1 at pci4 dev 4 function 1: Broadcom BCM5780 Gigabit Ethernet
bge1: interrupting at ioapic1 pin 11
bge1: ASIC BCM5714 B3 (0x8003), Ethernet address 00:e0:81:47:b0:f5
bge1: setting short Tx thresholds
brgphy1 at bge1 phy 1: BCM5780 1000BASE-T media interface, rev. 0
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ppb4 at pci0 dev 8 function 0: vendor 0x1166 product 0x0132 (rev. 0xa3)
pci5 at ppb4 bus 5
pci5: memory space enabled
ppb5 at pci0 dev 9 function 0: vendor 0x1166 product 0x0132 (rev. 0xa3)
pci6 at ppb5 bus 6
pci6: memory space enabled
ppb6 at pci0 dev 10 function 0: vendor 0x1166 product 0x0132 (rev. 0xa3)
pci7 at ppb6 bus 7
pci7: memory space enabled
ppb7 at pci0 dev 11 function 0: vendor 0x1166 product 0x0132 (rev. 0xa3)
pci8 at ppb7 bus 8
pci8: memory space enabled
vga0 at pci0 dev 12 function 0: vendor 0x1002 product 0x515e (rev. 0x02)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
radeondrm0 at vga0pci_mem_find: void region
pci_mem_find: void region
pci_mem_find: void region
: ATI ES1000 RN50
radeondrm0: Initialized radeon 1.29.0 20080613
pchb0 at pci0 dev 24 function 0: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb1 at pci0 dev 24 function 1: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb2 at pci0 dev 24 function 2: vendor 0x1022 product 0x1102 (rev. 0x00)
amdtemp0 at pci0 dev 24 function 3: AMD CPU Temperature Sensors (K8: core rev 
JH-F2, socket F)
pchb3 at pci0 dev 25 function 0: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb4 at pci0 dev 25 function 1: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb5 at pci0 dev 25 function 2: vendor 0x1022 product 0x1102 (rev. 0x00)
amdtemp1 at pci0 dev 25 function 3: AMD CPU Temperature Sensors (K8: core rev 
JH-F2, socket F)
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
Initializing SSP: cd2de5fd7101136d 4ba02c741f97e621 d3563b4182aa691a 
2869e562250d45c6 f1160c6620827cc8 7881d064bc2e2016 c6fa7d472e9bebd9 
be6b621bb57c0ea5 
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
cpu1: TSC skew=30 drift=-27
cpu2: TSC skew=108 drift=-99
cpu3: TSC skew=58 drift=-3
TSC not known safe on this CPU
uhub0 at usb0: vendor 0x1166 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x1166 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x1166 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
cpu1: running
svwsata0 port 0: device present, speed: 1.5Gb/s
svwsata0 port 3: device present, speed: 1.5Gb/s
svwsata0 port 2: device present, speed: 1.5Gb/s
cpu2: running
cpu3: running
wd0 at atabus0 drive 0: <ST3400620NS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 372 GB, 775221 cyl, 16 head, 63 sec, 512 bytes/sect x 781422768 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(svwsata0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
svwsata0 port 1: PHY offline
wd1 at atabus2 drive 0: <ST3400620NS>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 372 GB, 775221 cyl, 16 head, 63 sec, 512 bytes/sect x 781422768 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd1(svwsata0:2:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd2 at atabus3 drive 0: <WDC WD4000YS-01MPB0>
wd2: drive supports 16-sector PIO transfers, LBA48 addressing
wd2: 372 GB, 775221 cyl, 16 head, 63 sec, 512 bytes/sect x 781422768 sectors
wd2: 32-bit data port
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd2(svwsata0:3:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
atapibus0 at atabus4: 2 targets
cd0 at atapibus0 drive 0: <QSI DVD-ROM SDR-083, , MX09> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
raidattach: Asked for 8 units
Kernelized RAIDframe activated
pad: requested 1 units
pad0: outputs: 44100Hz, 16-bit, stereo
audio0 at pad0: half duplex, playback, capture
Searching for RAID components...
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsdisplay0: screen 5 added (80x50, vt100 emulation)
wsdisplay0: screen 6 added (80x50, vt100 emulation)