Re: ACPI call for testing (take two)

To: current-users%NetBSD.org@localhost, port-amd64%NetBSD.org@localhost
Subject: Re: ACPI call for testing (take two)
From: Thilo Jeremias <thilo%nispuk.com@localhost>
Date: Tue, 11 Jan 2011 09:58:44 +0100
Jukka Ruohonen wrote:
> On Mon, Jan 10, 2011 at 08:41:56PM +0100, Thilo Jeremias wrote:
>   
>> cpu1 FPU synch IPI                               23        0 misc
>> cpu1 TLB IPI                                     23        0 misc
>> ioapic0 pin 9                           10756400675    98765 intr
>> acpicpu0 C1 (HALT)                      10377200592    95284 misc
>> acpicpu1 C1 (HALT)                         13742398      126 misc
>> ioapic0 pin 19                               812934        7 intr
>> ioapic0 pin 20                                 6938        0 intr
>> ioapic0 pin 14                               427946        3 intr
>> ioapic0 pin 15                              1178474       10 intr
>> ioapic0 pin 21                                   36        0 intr
>> ioapic0 pin 4                                   156        0 intr
>> kpreempt defer: critical section                  3        0 misc
>> kpreempt defer: kernel_lock                     115        0 misc
>> kpreempt immediate                             3661        0 misc
>>     
>
> So it indeed seems to cause a storm on pin 9, which is most likely the SCI.
> Can you try booting with options -x -v (see boothowto(8)) and posting the
> dmesg, so that we can see whether it is doing something stupid like trying
> to route the SCI as a PCI interrupt.
>
> - Jukka.
>   

Indeed:  acpi0: SCI interrupting at int 9

thilo


>> NetBSD/x86 BIOS Boot, Revision 5.3 (from NetBSD 5.99.13)
>> Memory: 636/2029440 k
> boot -x -v
booting hd0a:netbsd (howto 0xa0000)
10091124+546144+428700 [511936+499022]=0xb86240
Loading ffs 
BIOS CFG: Model-SubM-Rev: fc-01-00, 0x0x74<EBDA,KBDINT,RTC,IC2>
rbus: rbus_min_start set to 0x80000000
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.43 (GENERIC) #5: Sun Jan  9 12:17:42 CET 2011
        thilo@rescue:/mnt/obj.51head/sys/arch/i386/compile/GENERIC
total memory = 1982 MB
avail memory = 1936 MB
Prep module path=ffs len=216779 pa=c87000
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfa210
SMBIOS rev. 2.4 @ 0xf0000 (43 entries)
Winfast   ( )
mainbus0 (root)
cpu0 at mainbus0 apid 0cpu0: 8 page colors
cpu0: calibrating local timer
cpu0: apic clock running at 200 MHz
timecounter: Timecounter "lapic" frequency 200092312 Hz quality -100
: AMD 686-class, 2099MHz, id 0x60fb1
cpu0: PAT enabled
cpu1 at mainbus0 apid 1: AMD 686-class, 2099MHz, id 0x60fb1
cpu1: PAT enabled
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 3, 24 pins
ioapic0: misconfigured as apic 0
ioapic0: remapped to apic 2
ioapic1 at mainbus0 apid 3: pa 0xfecc0000, version 3, 24 pins
acpi0 at mainbus0: Intel ACPICA 20100528
acpi0: X/RSDT: OemId <K8M890,AWRDACPI,42302e31>, AslId <AWRD,00000000>
ALKB: Links after initial probe:
Link Device ALKB:
Index  IRQ  Rtd  Ref  IRQs
    0   21   N     0  21 polarity 1 trigger 0

ALKB: Links after initial validation:
Link Device ALKB:
Index  IRQ  Rtd  Ref  IRQs
    0   21   N     0  21 polarity 1 trigger 0

ALKB: Links after disable:
Link Device ALKB:
Index  IRQ  Rtd  Ref  IRQs
    0   21   Y     0  21 polarity 1 trigger 0

ALKA: Links after initial probe:
Link Device ALKA:
Index  IRQ  Rtd  Ref  IRQs
    0   20   N     0  20 polarity 1 trigger 0

ALKA: Links after initial validation:
Link Device ALKA:
Index  IRQ  Rtd  Ref  IRQs
    0   20   N     0  20 polarity 1 trigger 0

ALKA: Links after disable:
Link Device ALKA:
Index  IRQ  Rtd  Ref  IRQs
    0   20   Y     0  20 polarity 1 trigger 0

ALKC: Links after initial probe:
Link Device ALKC:
Index  IRQ  Rtd  Ref  IRQs
    0   22   N     0  22 polarity 1 trigger 0

ALKC: Links after initial validation:
Link Device ALKC:
Index  IRQ  Rtd  Ref  IRQs
    0   22   N     0  22 polarity 1 trigger 0

ALKC: Links after disable:
Link Device ALKC:
Index  IRQ  Rtd  Ref  IRQs
    0   22   Y     0  22 polarity 1 trigger 0

ALKD: Links after initial probe:
Link Device ALKD:
Index  IRQ  Rtd  Ref  IRQs
    0   23   N     0  23 polarity 1 trigger 0

ALKD: Links after initial validation:
Link Device ALKD:
Index  IRQ  Rtd  Ref  IRQs
    0   23   N     0  23 polarity 1 trigger 0

ALKD: Links after disable:
Link Device ALKD:
Index  IRQ  Rtd  Ref  IRQs
    0   23   Y     0  23 polarity 1 trigger 0

timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
acpi0: ACPI-Fast 24-bit timer
acpi0: warning: timer may be unreliable
acpicpu0 at acpi0 (CPU0): ACPI CPU
acpicpu0: C1: HLT, lat   0 us, pow     0 mW, flags 0x00
acpicpu1 at acpi0 (CPU1): ACPI CPU
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
PMIO (PNP0C02) at acpi0 not configured
SYSR (PNP0C02) at acpi0 not configured
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
npx1 at acpi0 (COPR, PNP0C04): io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
UAR1 (PNP0501) at acpi0 not configured
UAR2 (PNP0501) at acpi0 not configured
LPT1 (PNP0400) at acpi0 not configured
pckbc1 at acpi0 (PS2M, PNP0F13) (aux port): irq 12
pckbc2 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
EXPL (PNP0C02) at acpi0 not configured
MEM (PNP0C01) at acpi0 not configured
FAN (PNP0C0B) at acpi0 not configured
acpitz0 at acpi0 (THRM): ACPI Thermal Zone
acpitz0: polling interval 30.0 seconds
acpitz0: active cooling level 0: 73.0C
acpitz0: levels: critical 75.0 C, passive 73.0 C
apm0 at acpi0: Power Management spec V1.2
acpi0: fixed power button present
acpi0: SCI interrupting at int 9
attimer1: attached to pcppi1
pckbd0 at pckbc2 (kbd slot)
pckbc2: using irq 1 for kbd slot
wskbd0 at pckbd0 mux 1
pms0 at pckbc2 (aux slot)
pckbc2: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x1106 product 0x0336 (rev. 0x00)
agp0 at pchb0 (v3): aperture at 0xd0000000, size 0x10000000
pchb1 at pci0 dev 0 function 1: vendor 0x1106 product 0x1336 (rev. 0x00)
pchb2 at pci0 dev 0 function 2: vendor 0x1106 product 0x2336 (rev. 0x00)
pchb3 at pci0 dev 0 function 3: vendor 0x1106 product 0x3336 (rev. 0x00)
pchb4 at pci0 dev 0 function 4: vendor 0x1106 product 0x4336 (rev. 0x00)
vendor 0x1106 product 0x5336 (interrupt system, interface 0x20) at pci0
dev 0 function 5 not configured
pchb5 at pci0 dev 0 function 7: vendor 0x1106 product 0x7336 (rev. 0x00)
ppb0 at pci0 dev 1 function 0: vendor 0x1106 product 0xb188 (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga1 at pci1 dev 0 function 0: vendor 0x1106 product 0x3230 (rev. 0x11)
wsdisplay0 at vga1 kbdmux 1
wsmux1: connecting to wsdisplay0
wskbd0: connecting to wsdisplay0
viadrm0 at vga1pci_mem_find: void region
pci_mem_find: void region
pci_mem_find: void region
pci_mem_find: void region
: VIA K8M890
viadrm0: AGP at 0xd0000000 128MB
viadrm0: Initialized via 2.11.1 20070202
ppb1 at pci0 dev 2 function 0: vendor 0x1106 product 0xa238 (rev. 0x00)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 3 function 0: vendor 0x1106 product 0xc238 (rev. 0x00)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
bktr0 at pci0 dev 5 function 0
bktr0: interrupting at ioapic0 pin 16
bktr0: buffer size 3555328, addr 0x8000000
bktr0: GPIO is 0x00bff706
bktr0: subsystem 0x107d 0xff06
bktr0: Leadtek WinFast TV2000/VC100, Philips FR1236 NTSC FM tuner.
radio0 at bktr0
radio0: WARNING: power management not supported
bktr0: WARNING: power management not supported
vendor 0x109e product 0x0878 (miscellaneous multimedia, revision 0x11)
at pci0 dev 5 function 1 not configured
rtk0 at pci0 dev 9 function 0: Realtek 8139 10/100BaseTX (rev. 0x10)
rtk0: interrupting at ioapic0 pin 19
rtk0: Ethernet address 00:15:58:6d:63:81
rlphy0 at rtk0 phy 7: Realtek internal PHY
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
viaide0 at pci0 dev 15 function 0: VIA Technologies VT8237 SATA
Controller (rev. 0x80)
viaide0: bus-master DMA support present
viaide0: primary channel configured to native-PCI mode
viaide0: using ioapic0 pin 20 for native-PCI interrupt
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to native-PCI mode
atabus1 at viaide0 channel 1
viaide1 at pci0 dev 15 function 1
viaide1: VIA Technologies VT8237 ATA133 controller
viaide1: bus-master DMA support present
viaide1: primary channel configured to compatibility mode
viaide1: primary channel interrupting at ioapic0 pin 14
atabus2 at viaide1 channel 0
viaide1: secondary channel configured to compatibility mode
viaide1: secondary channel interrupting at ioapic0 pin 15
atabus3 at viaide1 channel 1
uhci0 at pci0 dev 16 function 0: vendor 0x1106 product 0x3038 (rev. 0x81)
uhci0: interrupting at ioapic0 pin 21
usb0 at uhci0: USB revision 1.0
usb0: WARNING: power management not supported
uhci1 at pci0 dev 16 function 1: vendor 0x1106 product 0x3038 (rev. 0x81)
uhci1: interrupting at ioapic0 pin 21
usb1 at uhci1: USB revision 1.0
usb1: WARNING: power management not supported
uhci2 at pci0 dev 16 function 2: vendor 0x1106 product 0x3038 (rev. 0x81)
uhci2: interrupting at ioapic0 pin 21
usb2 at uhci2: USB revision 1.0
usb2: WARNING: power management not supported
uhci3 at pci0 dev 16 function 3: vendor 0x1106 product 0x3038 (rev. 0x81)
uhci3: interrupting at ioapic0 pin 21
usb3 at uhci3: USB revision 1.0
usb3: WARNING: power management not supported
ehci0 at pci0 dev 16 function 4: vendor 0x1106 product 0x3104 (rev. 0x86)
ehci0: interrupting at ioapic0 pin 21
ehci0: dropped intr workaround enabled
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
usb4: WARNING: power management not supported
viapcib0 at pci0 dev 17 function 0: vendor 0x1106 product 0x3227 (rev. 0x00)
viapcib0: SMBus found at 0x500 (revision 0x0)
iic0 at viapcib0: I2C bus
auvia0 at pci0 dev 17 function 5: VIA Technologies VT8237 AC'97 Audio
(rev 0x60)
auvia0: interrupting at ioapic0 pin 22
auvia0: ac97: Avance Logic ALC655 codec; no 3D stereo
auvia0: ac97: ext id 0x9c4<AC97_23,LDAC,SDAC,CDAC,SPDIF>
audio0 at auvia0: full duplex, playback, capture, independent
pchb6 at pci0 dev 24 function 0: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb7 at pci0 dev 24 function 1: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb8 at pci0 dev 24 function 2: vendor 0x1022 product 0x1102 (rev. 0x00)
amdtemp0 at pci0 dev 24 function 3: AMD CPU Temperature Sensors (K8:
core rev BH-G1, socket AM2)
amdtemp0: Workaround enabled
isa0 at viapcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
Initializing SSP: 357df5b0 c9e0498f 3742b076 d4e4365c c61fd586 a3b43357
5632a8eb 90b6f459
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
cpu1: TSC skew=-104489 drift=-21
TSC not known safe on this CPU
timecounter: Timecounter "TSC" frequency 2099936640 Hz quality -100
cpu1: running
acpicpu0: ACPI CPUs started (cap 0x00, flags 0x011621)
uhub0 at usb0: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb3: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb4: vendor 0x1106 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 8 ports with 8 removable, self powered
uhub4 at usb2: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
viaide0 port 1: device present, speed: 1.5Gb/s
wd0 at atabus1 drive 0: <ST31000333AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 931 GB, 1938021 cyl, 16 head, 63 sec, 512 bytes/sect x 1953525168
sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(viaide0:1:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
atapibus0 at atabus2: 2 targets
cd0 at atapibus0 drive 0: <PIONEER DVD-RW  DVR-109, EADL078870WL, 1.58>
cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd1 at atabus2 drive 1: <FUJITSU MPF3102AT>
wd1: drive supports 16-sector PIO transfers, LBA addressing
wd1: 9773 MB, 19857 cyl, 16 head, 63 sec, 512 bytes/sect x 20015856 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
cd0(viaide1:0:0): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA)
wd1(viaide1:0:1): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA)
uhidev0 at uhub3 port 4 configuration 1 interface 1
uhidev0: Afatech DVB-T, rev 2.00/2.00, addr 2, iclass 3/0
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub0 port 1 configuration 1 interface 0
wd2 at atabus3 drive 0: <WDC WD3200JB-00KFA0>
wd2: drive supports 16-sector PIO transfers, LBA48 addressing
wd2: 298 GB, 620181 cyl, 16 head, 63 sec, 512 bytes/sect x 625142448 sectors
wd2: 32-bit data port
wd2: drive supports PIO mode 4uhidev1: PATEN USB/PS2 Combo Receiver, rev
1.10/1.04, addr 2, iclass 3/1
, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd2(viaide1:1:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
crypto: assign driver 0, flags 2
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 19 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 20 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 21 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
crypto: driver 0 registers alg 22 flags 0 maxoplen 0
raidattach: Asked for 8 units
Kernelized RAIDframe activated
Searching for RAID components...
ums0 at uhidev1: 3 buttons and Z dir
wsmouse1 at ums0 mux 0
boot device: wd1
root on wd1a dumps on wd1b
root file system type: ffs
Tue Jan 11 09:41:02 CET 2011
Starting root file system check:
/dev/rwd1a: file system is clean; not checking
swapctl: adding /dev/wd1b as swap device at priority 0
Starting file system checks:
/dev/rwd1a: file system is mounted read-write on /; not checking
Setting tty flags.
Setting sysctl variables:
kern.no_sa_support: 1 -> 1
ddb.onpanic: 1 -> 0
net.inet.ip.forwarding: 0 -> 1
Starting network.
References:
- ACPI call for testing (take two)
  - From: Jukka Ruohonen
- Re: ACPI call for testing (take two)
  - From: thilo
- Re: ACPI call for testing (take two)
  - From: Joerg Sonnenberger
- Re: ACPI call for testing (take two)
  - From: Thilo Jeremias
- Re: ACPI call for testing (take two)
  - From: Jukka Ruohonen
Prev by Date: Re: ACPI call for testing (take two)
Next by Date: miniroot.kmod install fs + amd64cd.iso changes
Previous by Thread: Re: ACPI call for testing (take two)
Next by Thread: Re: ACPI call for testing (take two)
Indexes:
Home | Main Index | Thread Index | Old Index