This is a dmesg from one of these with 6 bnx devices, but I think it
shows that 610/710 are similar.
Have you tried ping flooding your router from the web server?
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 5.0_STABLE (GENERIC) #6: Sun Feb 28 15:26:26 EST 2010
gdt%ir.bbn.com@localhost:/n0/obj/gdt-5/amd64/sys/arch/amd64/compile/GENERIC
total memory = 4086 MB
avail memory = 3945 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
SMBIOS rev. 2.6 @ 0xcf79c000 (83 entries)
Dell Inc. PowerEdge R610
mainbus0 (root)
cpu0 at mainbus0 apid 16: Intel 686-class, 1862MHz, id 0x106a5
cpu1 at mainbus0 apid 20: Intel 686-class, 1862MHz, id 0x106a5
ioapic0 at mainbus0 apid 0: pa 0xfec00000, version 20, 24 pins
ioapic1 at mainbus0 apid 1: pa 0xfec80000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <DELL ,PE_SC3 ,00000001>, AslId <DELL,00000001>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
ACPI-Safe 24-bit timer
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x5f irq 0
COMA (PNP0501) at acpi0 not configured
COMB (PNP0501) at acpi0 not configured
hpet0 at acpi0 (HPET, PNP0103-0): mem 0xfed00000-0xfed003ff
timecounter: Timecounter "hpet0" frequency 14318179 Hz quality 2000
ipmi0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x3403 (rev. 0x13)
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x3408 (rev. 0x13)
ppb0: unsupported PCI Express version
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
bnx0 at pci1 dev 0 function 0: Broadcom NetXtreme II BCM5709 1000Base-T
bnx0: interrupting at ioapic1 pin 4
brgphy0 at bnx0 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bnx1 at pci1 dev 0 function 1: Broadcom NetXtreme II BCM5709 1000Base-T
bnx1: interrupting at ioapic1 pin 16
brgphy1 at bnx1 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ppb1 at pci0 dev 3 function 0: vendor 0x8086 product 0x340a (rev. 0x13)
ppb1: unsupported PCI Express version
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
bnx2 at pci2 dev 0 function 0: Broadcom NetXtreme II BCM5709 1000Base-T
bnx2: interrupting at ioapic1 pin 0
brgphy2 at bnx2 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8
brgphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bnx3 at pci2 dev 0 function 1: Broadcom NetXtreme II BCM5709 1000Base-T
bnx3: interrupting at ioapic1 pin 10
brgphy3 at bnx3 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8
brgphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ppb2 at pci0 dev 7 function 0: vendor 0x8086 product 0x340e (rev. 0x13)
ppb2: unsupported PCI Express version
pci3 at ppb2 bus 4
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
bnx4 at pci3 dev 0 function 0: Broadcom NetXtreme II BCM5709 1000Base-T
bnx4: interrupting at ioapic1 pin 6
brgphy4 at bnx4 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8
brgphy4: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bnx5 at pci3 dev 0 function 1: Broadcom NetXtreme II BCM5709 1000Base-T
bnx5: interrupting at ioapic1 pin 13
brgphy5 at bnx5 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8
brgphy5: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ppb3 at pci0 dev 9 function 0: vendor 0x8086 product 0x3410 (rev. 0x13)
ppb3: unsupported PCI Express version
pci4 at ppb3 bus 5
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x8086 product 0x342e (interrupt system, revision 0x13) at pci0 dev 20
function 0 not configured
vendor 0x8086 product 0x3422 (interrupt system, revision 0x13) at pci0 dev 20
function 1 not configured
vendor 0x8086 product 0x3423 (interrupt system, revision 0x13) at pci0 dev 20
function 2 not configured
uhci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x2937 (rev. 0x02)
uhci0: interrupting at ioapic0 pin 17
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: vendor 0x8086 product 0x2938 (rev. 0x02)
uhci1: interrupting at ioapic0 pin 18
usb1 at uhci1: USB revision 1.0
ehci0 at pci0 dev 26 function 7: vendor 0x8086 product 0x293c (rev. 0x02)
ehci0: interrupting at ioapic0 pin 19
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1
usb2 at ehci0: USB revision 2.0
ppb4 at pci0 dev 28 function 0: vendor 0x8086 product 0x2940 (rev. 0x02)
pci5 at ppb4 bus 3
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
mpt0 at pci5 dev 0 function 0: vendor 0x1000 product 0x0058
mpt0: interrupting at ioapic0 pin 16
mpt0: Phy 0: Link Rate 3.0 Gbps
scsibus0 at mpt0: 112 targets, 8 luns per target
uhci2 at pci0 dev 29 function 0: vendor 0x8086 product 0x2934 (rev. 0x02)
uhci2: interrupting at ioapic0 pin 21
usb3 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 1: vendor 0x8086 product 0x2935 (rev. 0x02)
uhci3: interrupting at ioapic0 pin 20
usb4 at uhci3: USB revision 1.0
ehci1 at pci0 dev 29 function 7: vendor 0x8086 product 0x293a (rev. 0x02)
ehci1: interrupting at ioapic0 pin 21
ehci1: EHCI version 1.0
ehci1: companion controllers, 2 ports each: uhci2 uhci3
usb5 at ehci1: USB revision 2.0
ppb5 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0x92)
pci6 at ppb5 bus 6
pci6: i/o space, memory space enabled
vga0 at pci6 dev 3 function 0: vendor 0x102b product 0x0532 (rev. 0x0a)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x2918 (rev. 0x02)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
piixide0 at pci0 dev 31 function 2
piixide0: Intel 82801I Serial ATA Controller (ICH9) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel configured to native-PCI mode
piixide0: using ioapic0 pin 23 for native-PCI interrupt
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to native-PCI mode
atabus1 at piixide0 channel 1
isa0 at ichlpcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
attimer1: attached to pcppi0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 1862131240 Hz quality 3000
scsibus0: waiting 2 seconds for devices to settle...
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
uhub3 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub5: 4 ports with 4 removable, self powered
uhub6 at uhub2 port 3: vendor 0x0424 product 0x2514, class 9/0, rev 2.00/0.00,
addr 2
uhub6: multiple transaction translators
uhub6: 3 ports with 3 removable, self powered
sd0 at scsibus0 target 0 lun 0: <ATA, FUJITSU MHZ2080B, 8A22> disk fixed
sd0: 76319 MB, 76320 cyl, 16 head, 127 sec, 512 bytes/sect x 156301488 sectors
probe(mpt0:0:8:0): generic HBA error
uhidev0 at uhub3 port 2 configuration 1 interface 0
uhidev0: Avocent USB Composite Device-0, rev 1.10/0.00, addr 2, iclass 3/1
ukbd0 at uhidev0
uhub7 at uhub6 port 2: Mitsumi Electric Hub in Apple Extended USB Keyboard,
class 9/0, rev 1.10/4.10, addr 3
uhub7: 3 ports with 2 removable, bus powered
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub3 port 2 configuration 1 interface 1
uhidev1: Avocent USB Composite Device-0, rev 1.10/0.00, addr 2, iclass 3/1
ums0 at uhidev1: 3 buttons and Z dir
wsmouse0 at ums0 mux 0
uhidev2 at uhub7 port 2 configuration 1 interface 0
uhidev2: Logitech Apple Optical USB Mouse, rev 2.00/3.40, addr 4, iclass 3/1
ums1 at uhidev2: 1 button
wsmouse1 at ums1 mux 0
uhidev3 at uhub7 port 3 configuration 1 interface 0
uhidev3: Mitsumi Electric Apple Extended USB Keyboard, rev 1.10/4.10, addr 5,
iclass 3/1
ukbd1 at uhidev3
wskbd2 at ukbd1 mux 1
wskbd2: connecting to wsdisplay0
uhidev4 at uhub7 port 3 configuration 1 interface 1
uhidev4: Mitsumi Electric Apple Extended USB Keyboard, rev 1.10/4.10, addr 5,
iclass 3/0
uhidev4: 3 report ids
uhid0 at uhidev4 reportid 2: input=1, output=0, feature=0
uhid1 at uhidev4 reportid 3: input=3, output=0, feature=0
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 0: <TEAC DVD-ROM DV-28SW, 10020512162737, R.2A> cdrom
removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
cd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
ipmi0: version 2.0 interface KCS iobase 0xca8/8 spacing 4
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio0 at pad0: half duplex, playback, capture
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
ipmi0: critical over limit on 'Temp6'
Attachment:
pgpKox4Euxi0j.pgp
Description: PGP signature