-current not detecting cd/dvd rw on compaq presario R3000

["Michael Litchard" <michael%schmong.org@localhost>]

Couldn't find anything about this via google. I figure the place to begin
is with a dmesg.
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.65 (GENERIC) #0: Wed Jun 18 09:15:17 PDT 2008
        
builds@wb28:/home/builds/ab/HEAD/amd64/200806180002Z-obj/home/builds/ab/H
EAD/src/sys/arch/amd64/compile/GENERIC
total memory = 1023 MB
avail memory = 974 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
SMBIOS rev. 2.31 @ 0xf09b0 (20 entries)
Hewlett-Packard  Presario R3200 (DP533AV)       (F.30)
mainbus0 (root)
cpu0 at mainbus0 apid 0: AMD 686-class, 797MHz, id 0xf4a
cpu0: erratum 86 present
cpu0: erratum 89 present
cpu0: erratum 97 present
cpu0: erratum 104 present
cpu0: erratum 101 present
cpu0: erratum 106 present
cpu0: erratum 107 present
cpu0: WARNING: errata present, BIOS upgrade may be
cpu0: WARNING: necessary to ensure reliable operation
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 11, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <PTLTD ,  RSDT  ,06040000>, AslId < LTP,00000000>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
WMID (pnp0c14) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
acpiacad0 at acpi0 (ACAD, ACPI0003): ACPI AC Adapter
acpiec0 at acpi0 (EC0, PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
acpibat0 at acpi0 (BAT1, PNP0C0A-1): ACPI Battery (Control Method)
acpibat0: battery info: Hewlett-Packard , Lion, Primary
attimer1 at acpi0 (PIT0, PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPK0, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
pckbc1 at acpi0 (PS2K, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, PNP0F13): aux port
pckbc2: irq 12
ECP1 (PNP0401) at acpi0 not configured
acpitz0 at acpi0 (THRM): critical 90.0C passive 31.0C, passive cooling
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x10de product 0x00d1 (rev. 0xa4)
agp0 at pchb0: 1 Miscellaneous Control unit(s) found.
agp0: aperture at 0xe8000000, size 0x8000000
pcib0 at pci0 dev 1 function 0
pcib0: vendor 0x10de product 0x00d0 (rev. 0xa6)
nfsmbc0 at pci0 dev 1 function 1: vendor 0x10de product 0x00d4 (rev. 0xa4)
nfsmb0 at nfsmbc0 SMBus 1
iic0 at nfsmb0: I2C bus
nfsmb1 at nfsmbc0 SMBus 2
iic1 at nfsmb1: I2C bus
ohci0 at pci0 dev 2 function 0: vendor 0x10de product 0x00d7 (rev. 0xa5)
LUS0: Picked IRQ 20 with weight 0
ohci0: interrupting at ioapic0 pin 20
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 2 function 1: vendor 0x10de product 0x00d7 (rev. 0xa5)
LUS1: Picked IRQ 21 with weight 0
ohci1: interrupting at ioapic0 pin 21
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
ehci0 at pci0 dev 2 function 2: vendor 0x10de product 0x00d8 (rev. 0xa2)
LUS2: Picked IRQ 22 with weight 0
ehci0: interrupting at ioapic0 pin 22
ehci0: EHCI version 1.0
ehci0: companion controllers, 4 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
auich0 at pci0 dev 6 function 0: nForce3 MCP-T AC-97 Audio
LACI: Picked IRQ 20 with weight 1
auich0: interrupting at ioapic0 pin 20
auich0: ac97: Analog Devices AD1981B codec; headphone, 20 bit DAC, no 3D stereo
auich0: ac97: ext id 605<AC97_22,AMAP,SPDIF,VRA>
vendor 0x10de product 0x00d9 (modem communications, revision 0xa2) at
pci0 dev 6
function 1 not configured
viaide0 at pci0 dev 8 function 0
viaide0: NVIDIA nForce3 IDE Controller (rev. 0xa5)
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at ioapic0 pin 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at ioapic0 pin 15
atabus1 at viaide0 channel 1
ppb0 at pci0 dev 10 function 0: vendor 0x10de product 0x00dd (rev. 0xa2)
pci1 at ppb0 bus 2
pci1: i/o space, memory space enabled
fwohci0 at pci1 dev 0 function 0: vendor 0x104c product 0x8026 (rev. 0x00)
LNK1: Picked IRQ 16 with weight 0
fwohci0: interrupting at ioapic0 pin 16
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 51:3f:02:00:51:3f:02:00
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
rtk0 at pci1 dev 1 function 0: Realtek 8139 10/100BaseTX (rev. 0x10)
LNK2: Picked IRQ 18 with weight 0
rtk0: interrupting at ioapic0 pin 18
rtk0: Ethernet address 00:0f:b0:48:cb:ca
rlphy0 at rtk0 phy 7: Realtek internal PHY
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vendor 0x14e4 product 0x4320 (miscellaneous network, revision 0x03) at
pci1 dev 2
 function 0 not configured
cbb0 at pci1 dev 4 function 0: vendor 0x104c product 0xac54 (rev. 0x01)
cbb1 at pci1 dev 4 function 1: vendor 0x104c product 0xac54 (rev. 0x01)
vendor 0x104c product 0x8201 (miscellaneous system, revision 0x01) at
pci1 dev 4
function 2 not configured
cbb0: cacheline 0x8 lattimer 0x40
cbb0: bhlc 0x824008
cbb0: secondary bus number uninitialized; try PCI_BUS_FIXUP
cbb0: interrupting at ioapic0 pin 16
cardslot0 at cbb0 slot 0 flags 0
pcmcia0 at cardslot0
cbb1: cacheline 0x8 lattimer 0x40
cbb1: bhlc 0x824008
cbb1: secondary bus number uninitialized; try PCI_BUS_FIXUP
cbb1: interrupting at ioapic0 pin 18
cardslot1 at cbb1 slot 1 flags 0
pcmcia1 at cardslot1
ppb1 at pci0 dev 11 function 0: vendor 0x10de product 0x00d2 (rev. 0xa4)
pci2 at ppb1 bus 1
pci2: i/o space, memory space enabled
vga0 at pci2 dev 0 function 0: vendor 0x10de product 0x0179 (rev. 0xa3)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
pchb1 at pci0 dev 24 function 0
pchb1: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb2 at pci0 dev 24 function 1
pchb2: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb3 at pci0 dev 24 function 2
pchb3: vendor 0x1022 product 0x1102 (rev. 0x00)
pchb4 at pci0 dev 24 function 3
pchb4: vendor 0x1022 product 0x1103 (rev. 0x00)
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
auich0: measured ac97 link rate at 47997 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
acpiacad0: AC adapter online.
uhub0 at usb0: vendor 0x10de OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: vendor 0x10de OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
uhub2 at usb2: vendor 0x10de EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 6 ports with 6 removable, self powered
wd0 at atabus0 drive 0: <TOSHIBA MK6025GAS>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 57231 MB, 116280 cyl, 16 head, 63 sec, 512 bytes/sect x 117210240 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex



What's the next step?

Michael Litchard