oops this tested amd64 version is the 3.1 release.  sorry.  I'll try 
latest netbsd-4 snapshot and report back in here.

thanks


Quoting pierre-philipp braun (12/04/2007 18:23),
> Dear amd64 port maintainers,
> 
> 
> should amd64 SMP work fine on Intel Core 2 (Merom) ?
> "Merom is the first Intel mobile processor to feature the Intel 64 
> 64-bit architecture."
> http://en.wikipedia.org/wiki/Intel_Core_2
> There are several models.  dmesg says T5600.
> 
> 
> I've installed both, netbsd-4/i386 (20070411 sources), and 
> netbsd-4/amd64 (20070411 snapshot) on that recent HP Compaq laptop.
> 
> 
> As for netbsd-4/i386 GENERIC.MP,
>     - it boots and works perfectly fine
>     - SMP works, two cpus are recognized
>     - sound doesn't work (I will address this on another email to 
> port-i386.  this mail is just about SMP on amd64)
>     - see dmesg below
> 
> 
> As for netbsd-4/amd64 GENERIC.MP,
>     - need to disable "azalia" audio driver to let it boot (otherwise it 
> hangs before mentioning this driver.  I'll eventually address this 
> later, once the SMP question is cleared and once the driver actually 
> works on that Intel ADI Hight def sound card within i386)
>     - only one CPU recognized
>     - see dmesg below
> 
> 
> i386 dmesg,
> 
> booting hd0a:netbsd
> 8911888+407940+357940 [435232+417104]=0xa0c4a4
> kenter: 0x00002000
> acpi: wakecode is installed at 0x2000, size=376
> BIOS CFG: Model-SubM-Rev: fc-01-00, 0x74<EBDA,KBDINT,RTC,IC2>
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 
> 2005, 2006
>     The NetBSD Foundation, Inc.  All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>     The Regents of the University of California.  All rights reserved.
> 
> NetBSD 4.0_BETA2 (GENERIC.MP) #0: Thu Apr 12 01:53:53 CEST 2007
> 
> elge@niet.nethence.com:/home/elge/netbsd-4/src/sys/arch/i386/compile/obj
> 
> /GENERIC.MP
> total memory = 1015 MB
> rbus: rbus_min_start set to 0x40000000
> avail memory = 987 MB
> timecounter: Timecounters tick every 10.000 msec
> timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
> BIOS32 rev. 0 found at 0xf0000
> mainbus0 (root)
> cpu0 at mainbus0: apid 0 (boot processor)
> cpu0: Intel Core 2 (Merom) (686-class), 1828.90 MHz, id 0x6f6
> cpu0: "Intel(R) Core(TM)2 CPU         T5600  @ 1.83GHz"
> cpu0: using thermal monitor 1
> cpu0: Enhanced SpeedStep (1340 mV) 1833 MHz
> cpu0: unknown Enhanced SpeedStep CPU.
> cpu0: using only highest and lowest power states.
> cpu0: Enhanced SpeedStep frequencies available (MHz): 1833 1000
> cpu0: calibrating local timer
> cpu0: apic clock running at 166 MHz
> cpu1 at mainbus0: apid 1 (application processor)
> cpu1: starting
> cpu1: Intel Core 2 (Merom) (686-class), 1828.75 MHz, id 0x6f6
> cpu1: "Intel(R) Core(TM)2 CPU         T5600  @ 1.83GHz"
> cpu1: using thermal monitor 1
> cpu1: Enhanced SpeedStep (1340 mV) 1833 MHz
> cpu1: unknown Enhanced SpeedStep CPU.
> cpu1: using only highest and lowest power states.
> cpu1: Enhanced SpeedStep frequencies available (MHz): 1833 1000
> ioapic0 at mainbus0 apid 1 (I/O APIC)
> ioapic0: pa 0xfec00000, version 20, 24 pins
> ioapic0: misconfigured as apic 0
> ioapic0: remapped to apic 1
> acpi0 at mainbus0: Advanced Configuration and Power Interface
> ACPI Error (evgpeblk-0394): Unknown GPE method type: C267 (name not of 
> form _Lxx
>  or _Exx) [20060217]
> acpi0: fixed-feature power button present
> timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
> ACPI-Fast 24-bit timer
> mpacpi: could not get bus number, assuming bus 0
> ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
> ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
> PNP0C01 [System Board] at acpi0 not configured
> PNP0A08 [PCI Express/PCI-X Mode-2 Host Bridge] at acpi0 not configured
> acpiec0 at acpi0 (PNP0C09): ACPI Embedded Controller
> acpiec0: io 0x62,0x66
> PNP0A06 [Generic Container Device] at acpi0 not configured
> com3 at acpi0 (PNP0501)
> com3: io 0x3f8-0x3ff irq 4
> com: ns16550a, working fifo
> com3: console
> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
> lpt3 at acpi0 (PNP0401)
> lpt3: io 0x378-0x37f,0x778-0x77a irq 7 drq 1
> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
> IFX0102 at acpi0 not configured
> npx1 at acpi0 (PNP0C04)
> npx1: io 0xf0-0xff irq 13
> attimer1 at acpi0 (PNP0100): AT Timer
> attimer1: io 0x40-0x43 irq 0
> PNP0200 [AT DMA Controller] at acpi0 not configured
> pcppi1 at acpi0 (PNP0800)
> pcppi1: io 0x61
> pcppi1: children must have an explicit unit
> midi0 at pcppi1: PC speaker (CPU-intensive output)
> sysbeep0 at pcppi1
> PNP0B00 [AT Real-Time Clock] at acpi0 not configured
> pckbc1 at acpi0 (PNP0303): kbd port
> pckbc1: io 0x60,0x64 irq 1
> pckbc2 at acpi0 (SYN0112): aux port
> pckbc2: irq 12
> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
> PNP0000 [AT Interrupt Controller] at acpi0 not configured
> PNP0C02 [Plug and Play motherboard register resources] at acpi0 not 
> configured
> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
> PNP0C0F [PCI interrupt link device] at acpi0 not configured
> PNP0C0F [PCI interrupt link device] at acpi0 not configured
> PNP0C0F [PCI interrupt link device] at acpi0 not configured
> PNP0C0F [PCI interrupt link device] at acpi0 not configured
> PNP0C0F [PCI interrupt link device] at acpi0 not configured
> PNP0C0F [PCI interrupt link device] at acpi0 not configured
> PNP0C0F [PCI interrupt link device] at acpi0 not configured
> PNP0C02 [Plug and Play motherboard register resources] at acpi0 not 
> configured
> HPQ0006 at acpi0 not configured
> acpibat0 at acpi0 (PNP0C0A-1): ACPI Battery (Control Method)
> acpibat1 at acpi0 (PNP0C0A-2): ACPI Battery (Control Method)
> acpiacad0 at acpi0 (ACPI0003): ACPI AC Adapter
> acpibut0 at acpi0 (PNP0C0E): ACPI Sleep Button
> acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
> PNP0C14 at acpi0 not configured
> PNP0C02 [Plug and Play motherboard register resources] at acpi0 not 
> configured
> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
> ACPI Object Type 'Power' (0x0b) at acpi0 not configured
> PNP0C0B [ACPI Fan] at acpi0 not configured
> PNP0C0B [ACPI Fan] at acpi0 not configured
> PNP0C0B [ACPI Fan] at acpi0 not configured
> PNP0C0B [ACPI Fan] at acpi0 not configured
> acpitz0 at acpi0: ACPI Thermal Zone
> acpitz0: active cooling level 0: 80.0C
> acpitz0: active cooling level 1: 70.0C
> acpitz0: active cooling level 2: 60.0C
> acpitz0: active cooling level 3: 50.0C
> acpitz0:
> acpitz1 at acpi0: ACPI Thermal Zone
> acpitz1: critical 105.0C passive 79.0C
> acpitz2 at acpi0: ACPI Thermal Zone
> acpitz2: critical 105.0C
> acpitz3 at acpi0: ACPI Thermal Zone
> acpiec0: EcRead: timeout waiting for EC to send data
> ACPI Exception (evregion-0521): AE_ERROR, Returned
> ol] [20060217]
> ACPI Exception (dswexec-0568): AE_ERROR, While resolving operands for 
> [AE_NOT_CO
> NFIGURED] [20060217]
> ACPI Error (psparse-0626): Method parse/execution failed [\_TZ_.C30E] 
> (Node 0xc1
> f2b360), AE_ERROR
> ACPI Error (psparse-0626): Method parse/execution failed 
> [\_TZ_.TZ3_._TMP] (Node
>  0xc1f2dac0), AE_ERROR
> acpitz3: critical 105.0C passive -273.-3C
> acpiec0: EcRead: timeout waiting for EC to send data
> ACPI Exception (evregion-0521): AE_ERROR, Returned by Handler for 
> [EmbeddedContr
> ol] [20060217]
> ACPI Exception (dswexec-0568): AE_ERROR, While resolving operands for 
> [AE_NOT_CO
> NFIGURED] [20060217]
> ACPI Error (psparse-0626): Method parse/execution failed [\_TZ_.C30E] 
> (Node 0xc1
> f2b360), AE_ERROR
> ACPI Error (psparse-0626): Method parse/execution failed 
> [\_TZ_.TZ3_._TMP] (Node
>  0xc1f2dac0), AE_ERROR
> acpitz3: failed to evaluate _TMP
> acpitz4 at acpi0: ACPI Thermal Zone
> acpitz4: critical 110.0C
> pcppi1: attached to attimer1
> pckbd0 at pckbc1 (kbd slot)
> pckbc1: using irq 1 for kbd slot
> wskbd0 at pckbd0 mux 1
> pms0 at pckbc1 (aux slot)
> pckbc1: using irq 12 for aux slot
> wsmouse0 at pms0 mux 0
> pci0 at mainbus0 bus 0: configuration mode 1
> pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
> pchb0 at pci0 dev 0 function 0
> pchb0: Intel 82945GM/PM/GMS Host Bridge (rev. 0x03)
> agp0 at pchb0: detected 7932k stolen memory
> agp0: aperture at 0xd0000000, size 0x10000000
> vga1 at pci0 dev 2 function 0: Intel 82945GM/PM/GMS Integrated Graphics 
> Device (
> rev. 0x03)
> wsdisplay0 at vga1 kbdmux 1
> wsmux1: connecting to wsdispla
> wskbd0: connecting to wsdisplay0
> Intel 82945GM/PM/GMS Integrated Graphics Device (miscellaneous display, 
> revision
>  0x03) at pci0 dev 2 function 1 not configured
> azalia0 at pci0 dev 27 function 0: Generic High Definition Audio Controller
> azalia0: interrupting at ioapic0 pin 21 (irq 10)
> azalia0: host: Intel 82801GB/GR High Definition Audio Controller (rev. 1)
> azalia0: host: High Definition Audio rev. 1.0
> ppb0 at pci0 dev 28 function 0: Intel 82801GB/GR PCI Express Port #1 
> (rev. 0x01)
> 
> pci1 at ppb0 bus 8
> pci1: i/o space, memory space enabled, rd/line, wr/inv ok
> wpi0 at pci1 dev 0 function 0: Intel PRO/Wireless LAN 3945ABG Mini-PCI 
> Adapter (
> rev. 0x02)
> wpi0: interrupting at ioapic0 pin 16 (irq 11)
> wpi0: 802.11 address 00:18:de:bc:c9:3d
> wpi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
> wpi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
> wpi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 
> 24Mbps 36M
> bps 48Mbps 54Mbps
> ppb1 at pci0 dev 28 function 2: Intel 82801GB/GR PCI Express Port #3
> 
> pci2 at ppb1 bus 24
> pci2: i/o space, memory space enabled, rd/line, wr/inv ok
> ppb2 at pci0 dev 28 function 3: Intel 82801GB/GR PCI Express Port #4 
> (rev. 0x01)
> 
> pci3 at ppb2 bus 32
> pci3: i/o space, memory space enabled, rd/line, wr/inv ok
> uhci0 at pci0 dev 29 function 0: Intel 82801GB/GR USB UHCI Controller 
> (rev. 0x01
> )
> uhci0: interrupting at ioapic0 pin 20 (irq 10)
> usb0 at uhci0: USB revision 1.0
> uhub0 at usb0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self power
> uhci1 at pci0 dev 29 function 1: Intel 82801GB/GR USB UHCI Controller 
> (rev. 0x01
> )
> uhci1: interrupting at ioapic0 pin 21 (irq 11)
> usb1 at uhci1: USB revision 1.0
> uhub1 at usb1
> uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> uhci2 at pci0 dev 29 function 2: Intel 82801GB/GR USB UHCI Controller 
> (rev. 0x01
> )
> uhci2: interrupting at ioapic0 pin 18 (irq 11)
> usb2 at uhci2: USB revision 1.0
> uhub2 at usb2
> uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr
> uhub2: 2 ports with 2 removable, self powered
> uhci3 at pci0 dev 29 function 3: Intel 82801GB/GR USB UHCI Controller 
> (rev. 0x01
> )
> uhci3: interrupting at ioapic0 pin 19 (irq 10)
> usb3 at uhci3: USB revision 1.0
> uhub3 at usb3
> uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub3: 2 ports with 2 removable, self powered
> ehci0 at pci0 dev 29 function 7: Intel 82801GB/GR USB EHCI Controller 
> (rev. 0x01
> )
> ehci0: interrupting at ioapic0 pin 20 (irq 10)
> ehci0: BIOS has given up ownership
> ehci0: EHCI version 1.0
> ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
> usb4 at ehci0: USB revision 2.0
> uhub4 at usb4
> uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub4: 8 ports with 8 removable, self powered
> ppb3 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0xe1)
> pci4 at ppb3 bus 2
> pci4: i/o space, memory space enabled
> cbb0 at pci4 dev 6 function 0: Texas Instruments product 0x8039 (rev. 0x00)
> fwohci0 at pci4 dev 6 function 1: Texas Instruments product 0x803a (rev. 
> 0x00)
> fwohci0: interrupting at ioapic0 pin 19 (irq 10)
> fwohci0: OHCI version 1.10 (ROM=0)
> fwohci0: No. of Isochronous channels is 4.
> fwohci0: EUI64 00:02:3f:99:29:91:47:0c
> fwohci0: Phy 1394a available S400, 3 ports.
> fwohci0: Link S400, max_rec 2048 bytes.
> ieee1394if0 at fwohci0: IEEE1394 bus
> fwip0 at ieee1394if0: IP over IEEE1394
> fwohci0: Initiate bus reset
> Texas Instruments product 0x803b (miscellaneous mass storage) at pci4 
> dev 6 func
> tion 2 not configured
> Texas Instruments product 0x803c (SD Host Controller system)
> ion 3 not configured
> Texas Instruments product 0x803d (miscellaneous communications) at pci4 
> dev 6 fu
> nction 4 not configured
> bge0 at pci4 dev 14 function 0: Broadcom BCM5788 Gigabit Ethernet
> bge0: interrupting at ioapic0 pin 16 (irq 11)
> bge0: ASIC BCM5705 A3 (0x3003), Ethernet address 00:17:08:41:9a:1c
> bge0: setting short Tx thresholds
> brgphy0 at bge0 phy 1: BCM5705 1000BASE-T media interface, rev. 2
> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
> 1000baseT-FD
> X, auto
> cbb0: interrupting at i
> cardslot0 at cbb0 slot 0 flags 0
> cardbus0 at cardslot0: bus 3
> pcmcia0 at cardslot0
> pcib0 at pci0 dev 31 function 0
> pcib0: Intel 82801GBM LPC Interface Bridge (rev. 0x01)
> piixide0 at pci0 dev 31 function 2
> piixide0: Intel 82801GBM/GHM Serial ATA Controller (ICH7) (rev. 0x01)
> piixide0: bus-master DMA support present
> piixide0: primary channel wired to compatibility mode
> piixide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
> atabus0 at piixide0 channel 0
> piixide0: secondary channel wired to compatibility m
> piixide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
> atabus1 at piixide0 channel 1
> isa0 at pcib0
> isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
> isapnp0: no ISA Plug 'n Play devices found
> ioapic0: enabling
> WARNING: Callback scheduled before sysmon task queue thread present.
> WARNING: Callback scheduled before sysmon task queue thread present.
> fwohci0: node_id=0xc800ffc0, gen=2, CYCLEMASTER mode
> ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
> ieee1394if0: bus manager 0 (me)
> fwohci0: phy int
> timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
> azalia0: codec[0]: Analog Devices AD1981HD (rev. 2.0)
> azalia0: codec[0]: High Definition Audio rev. 1.0
> azalia0: playback: max channels=2, encodings=1<PCM>
> azalia0: playback: PCM 
> formats=e007f<24bit,20bit,16bit,48kHz,44.1kHz,32kHz,22.05
> kHz,16kHz,11.025kHz,8kHz>
> azalia0: recording: max channels=2, encodings=1<PCM>
> azalia0: recording: PCM 
> formats=6007f<20bit,16bit,48kHz,44.1kHz,32kHz,22.05kHz,1
> 6kHz,11.025kHz,8kHz>
> azalia0: codec[1]: 0x11c1/0x3026 (rev. 7.0)
> azalia0: codec[1]: High Definition Audio rev. 1.0
> azalia0: codec[1]: No support for modem function groups
> azalia0: codec[1] has no audio function groups
> audio0 at azalia0: full duplex, independent
> Kernelized RAIDframe activated
> uhub5 at uhub4 port 1
> uhub5: Standard Microsystems product 0x2503, class 9/0, rev 2.00/0.01, 
> addr 2
> uhub5: multiple transaction translators
> uhub5: 3 ports with 0 removable, self powered
> ubt0 at uhub5 port 1 configuration 1 interface 0
> ubt0: Broadcom Corp HP Integrated Module, rev 2.00/1.00, addr 3
> wd0 at atabus0 drive 0: <FUJITSU MHV2080BH PL>
> wd0: drive supports 16-sector PIO transfers, LBA48 addressing
> wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 
> sectors
> wd0: 32-bit data port
> wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
> wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using 
> DMA)
> atapibus0 at atabus1: 2 targets
> cd0 at atapibus0 drive 0: <TSSTcorpCD/DVDW TS-L632D, , HH15
> cd0: 32-bit data port
> cd0: drive supports PIO mode 4, DMA mode 2
> cd0(piixide0:1:0): using PIO mode 4, DMA mode 2 (using DMA)
> ugen0 at uhub5 port 2
> ugen0: AuthenTec Fingerprint Sensor, rev 1.10/6.23, addr 4
> boot device: wd0
> root on wd0a dumps on wd0b
> root file system type: ffs
> cpu1: CPU 1 running
> Thu Apr 12 19:12:08 CEST 2007
> 
> 
> amd64 dmesg,
> 
>  > boot -c
> booting hd0f:netbsd (howto 0x1000)
> 6588752+673616+377648 [475128+289536]=0x904a38
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005
>     The NetBSD Foundation, Inc.  All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>     The Regents of the University of California.  All rights 
> reserved.][filename] [-acdqsv]
>      (ex. "hd0a:
> 
> NetBSD 3.1 (GENERIC.MP) #0: Mon Oct 30 21:51:09 UTC 2006
> dev xd[N[x]]:
> consdev {pc|com[0123]|c
> 
> builds@b1.netbsd.org:/home/builds/ab/netbsd-3-1-RELEASE/amd64/2006103020 
> boot hd0a:netbsd
> booting hd0a:netbsd
> 89118
> 53Z-obj/home/builds/ab/netbsd-3-1-RELEASE/src/sys/arch/amd64/compile/GENERIC.MP 
> 
> kenter: 0x00002000
> acpi: wakecode is installed at 0x2
> total memory = 1015 MB
> avail memory = 962 MBFG: Model-SubM-Rev: f
> userconf: configure system autoconfiguration:
> uc> disable azalia1996, 1997, 1998,
> [149] azalia* disabled 2003, 2004, 2005, 200
> uc> exit
> Continuing...
> mainbus0 (root)
> cpu0 at mainbus0: (uniprocessor)nc.  All rights reserved.
> cpu0: features: bffbfbff<FXSR,SSE,SSE2,B27,B28,LONG,3DNOW>
> /GENERIC.MP
> cpu0: L2 cache 2 MB 64B/line 8-way
> rbus: rbus_min_start se
> cpu0: 64 page colors
> pci0 at mainbus0 bus 0: configuration mode 1
> timecounter: Timecounters tick ev
> pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv 
> okecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
> pchb0 at pci0 dev 0 function 0
> pchb0: Intel product 0x27a0 (rev. 0x03)
> mainbus0 (root)
> cpu0: using only highest and lowest power states.
> ision 0x01) at pci0 dev 27 function 0 not configuredp frequencies 
> available (MHz): 1833 1000
> ppb0 at pci0 dev 28 function 0: Intel 82801GB/GR PCI Express Port #1 
> (rev. 0x01)
> cpu0: apic clock running at 166 MHz
> 
> pci1 at ppb0 bus 8
> cpu1 at mainbus0:
> pci1: i/o space, memory space enabled, rd/line, wr/inv o
> cpu1: starting
> 
> pci2: i/o space, memory space enabled, rd/line, wr/inv ok1: using only 
> highest and lowest power states.
> ppb2 at pci0 dev 28 function 3: Intel 82801GB/GR PCI Express Port #4 
> (rev. 0x01)able (MHz): 1833 1000
> 
> pci3 at ppb2 bus 32us0 apid 1 (I/O API
> pci3: i/o space, memory space enabled, rd/line, wr/inv ok0000, version 
> 20, 24 pins
> uhci0 at pci0 dev 29 function 0: Intel 82801GB/GR USB UHCI Controller 
> (rev. 0x01ic0: remapped to apic 1
> 
> )
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> acpi0: fixed-feature power button p
> uhci1 at pci0 dev 29 function 1: Intel 82801GB/GR USB UHCI Controller 
> (rev. 0x01st" frequency 3579545 Hz quality 1000
> )
> uhci1: interrupting at irq 11Fast 24-bit timer
> usb1 at uhci1: USB revision 1.0 bus number, assuming bus 0
> uhub1 at usb1
> uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 10 not 
> configured
> uhub1: 2 ports with 2 removable, self powered0x0c) at acpi0 not configured
> uhci2 at pci0 dev 29 function 2: Intel 82801GB/GR USB UHCI 
> Controlleracpi0 not configured
> 
> usb2 at uhci2: USB revision 1.0
> uhub2 at usb2
> acpiec0 at
> uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> acpiec0: io 0x62,0x66
> uhub2: 2 ports with 2 removable, self poweredvice] at acpi0 not configured
> uhci3 at pci0 dev 29 function 3: Intel 82801GB/GR USB UHCI Controller 
> (rev. 0x01
> com3: io 0x3f8-0x3ff irq 4
> com: ns16550a, wor
> )n
> uhci3: interrupting at irq 10
> com3: console
> usb3 at uhci3: USB revision 1.0) at acpi0 not configured
> uhub3 at usb3
> uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> lpt3: io 0x378-0x37f,0x778-0x77a irq 7 drq 1
> uhub3: 2 ports with 2 removable, self poweredect Type 'Power' (0x0b) at 
> acpi0 not configur
> Intel 82801GB/GR USB EHCI Controller (USB serial bus, interface 
> 0x20acpi0 not configured
> 
> pcppi1 at acpi0
> Texas Instruments product 0x8039 (CardBus bridge) at pci4 dev 6 function 
> 0 not cn must have an explicit unit
> midi0 at
> onfiguredC speaker
> Texas Instruments product 0x803a (Firewire serial bus, interface 0x10) 
> at pci4 d0 at pcppi1
> PNP0B00 [AT Real-Time Clock] at acpi0 not configur
> ev 6 function 1 not configured
> pckbc1
> Texas Instruments product 0x803b (miscellaneous mass storage) at pci4 
> dev 6 func0x64 irq 1
> pckbc2 at acpi0 (SYN0112): aux port
> tion 2 not configured
> pckbc2: irq 12
> bge0: ASIC BCM5705 A3 (0x3003), Ethernet address 00:17:08:41:9a:1cpi0 
> not configured
> bge0: setting short Tx thresholds link device] at acpi0 not config
> brgphy0 at bge0 phy 1: BCM5705 1000BASE-T media interface, rev. 2P0C0F 
> [PCI interrupt link device] at acpi0 not configured
> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-F
> PNP0C0F [PCI interrupt link device] a
> pciide0 at pci0 dev 31 function 2
> pciide0: Intel product 0x27c4 (rev. 0x01) device] at acpi0 not configured
> pciide0: bus-master DMA support present, but unused (no driver support)y 
> motherboard register resources] at acpi0 not configured
> pciide0: primary channel wired to compatibility mode
> HPQ0006 at acpi0 not configured
> pciide0: primary channel interrupting at irq 14A-1): ACPI Battery 
> (Control Method)
> atabus0 at pciide0 channel 0
> acpibat1
> pciide0: secondary channel wired to compatibility mode
> pciide0: secondary channel interrupting at irq 15
> ac
> atabus1 at pciide0 channel 1PI Sleep Button
> isa0 at pcib0
> pckbc0 at isa0 port 0x60-0x64
> pckbd0 at pckbc0 (kbd slot)
> ACPI Object Type 'Pow
> pckbc0: using irq 1 for kbd slotd
> wskbd0 at pckbd0 mux 1
> ACPI Object Type 'Po
> wskbd0: connecting to wsdisplay0ed
> pms0 at pckbc0 (aux slot)ACPI Object Type 'Power'
> pckbc0: using irq 12 for aux slot
> wsmouse0 at pms0 mux 0 Object Type 'Power' (
> pcppi0 at isa0 port 0x61ured
> midi0 at pcppi0: PC speaker
> PNP0C0B [ACPI Fan]
> sysbeep0 at pcppi0ured
> Kernelized RAIDframe activatedP0C0B [ACPI Fan] at acpi0 not
> uhub4 at uhub0 port 1
> uhub4: Standard Microsystems product 0x2503, class 9/0,
> 
> wd0 at atabus0 drive 0: <FUJITSU MHV2080BH PL>
> acpitz0: active cooling level 2: 60.0C
> wd0: drive supports 16-sector PIO transfers, LBA48 addressing3: 50.0C
> acpitz0:
> wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 
> sectorsz1: critical 105.0C passive 79.0C
> acpitz
> wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) 
> critical 105.0C
> acpitz3 at acpi0: ACPI Thermal
> atapibus0 at atabus1: 2 targets
> acpiec0: EcRead: timeou
> cd0 at atapibus0 drive 0: <TSSTcorpCD/DVDW TS-L632D, , HH15> cdrom 
> removable
> ACPI Exception (evregion-0521): AE_ERROR, Returned
> Thu Apr 12 20:12:54 CEST 2007
> ACPI Error (psp
> swapctl: adding /dev/wd0b as swap device at priority 0TMP] (Node
> swapctl: adding /dev/wd0g as swap device at priority 0RROR
> acpitz3: critical 105.0C pa
> Checking for botched superblock upgrades: done.
> acpiec0: EcRead: timeout waiting for EC
> Starting file system checks:
> 
> 
> # dmesg | grep cpu
> cpu0 at mainbus0: (uniprocessor)
> cpu0: Intel(R) Core(TM)2 CPU         T5600  @ 1.83GHz, 1828.86 MHz
> cpu0: features: bffbfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
> cpu0: features: bffbfbff<PGE,MCA,CMOV,PAT,PSE36,MPC,NOX,B21,MMXX,MMX>
> cpu0: features: bffbfbff<FXSR,SSE,SSE2,B27,B28,LONG,3DNOW>
> cpu0: L2 cache 2 MB 64B/line 8-way
> cpu0: 64 page colors
> #
> 
> 
> Thanks
> 
> Pierre-Philipp Braun
>