Jason,
Here is my boot log:
(boot dva0.0.0.0.1 -flags A)
block 0 of dva0.0.0.0.1 is a valid boot block
reading 87 blocks from dva0.0.0.0.1
bootstrap code read in
base = 1d8000, image_start = 0, image_bytes = ae00
initializing HWRPB at 2000
initializing page table at 1ca000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
NetBSD/alpha 9.2 ustar Bootstrap, Revision 1.3 (Mon May 17 16:06:32 UTC 2021)
VMS PAL rev: 0x1000000010114
OSF PAL rev: 0x1000000020116
Switch to OSF PAL code succeeded.
Boot flags: A
11015216/
Please remove disk 1, insert disk 2, and press return...
\
Please remove disk 2, insert disk 3, and press return...
/
Please remove disk 3, insert disk 4, and press return...
+206128=0xab39a0
Entering netbsd at 0xfffffc0000a011a0...
[ 1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
[ 1.0000000] 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
[ 1.0000000] 2018, 2019, 2020 The NetBSD Foundation, Inc. All rights reserved.
[ 1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[ 1.0000000] The Regents of the University of California. All rights reserved.
[ 1.0000000] NetBSD 9.2 (INSTALL) #0: Mon May 17 09:26:17 PDT 2021
[ 1.0000000] thorpej@stinky:/home/thorpej/netbsd-9-2-RELEASE/objdir/alpha/sys/arch/alpha/compile/INSTALL
[ 1.0000000] Digital Personal WorkStation 500au, 500MHz, s/n NI93703328
[ 1.0000000] 8192 byte page size, 1 processor.
[ 1.0000000] total memory = 640 MB
[ 1.0000000] (1896 KB reserved for PROM, 638 MB used by NetBSD)
[ 1.0000000] avail memory = 618 MB
[ 1.0000000] mainbus0 (root)
[ 1.0000000] cpu0 at mainbus0: ID 0 (primary), 21164A-0
[ 1.0000000] cpu0: Architecture extensions: 0x1<BWX>
[ 1.0000000] cia0 at mainbus0: DECchip 2117x Core Logic Chipset (Pyxis), pass 2
[ 1.0000000] cia0: extended capabilities: 0x1<BWEN>
[ 1.0000000] cia0: using BWX for PCI config access
[ 1.0000000] pci0 at cia0 bus 0
[ 1.0000000] tlp0 at pci0 dev 3 function 0: DECchip 21143 Ethernet, pass 3.0
[ 1.0000000] tlp0: interrupting at dec 550 irq 0
[ 1.0000000] tlp0: DEC, Ethernet address 00:00:f8:75:f0:19
[ 1.0000000] nsphy0 at tlp0 phy 5: DP83840 10/100 media interface, rev. 1
[ 1.0000000] nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
[ 1.0000000] tlp0: 10baseT, 10baseT-FDX, 10base2, 10base5
[ 1.0000000] sio0 at pci0 dev 7 function 0: vendor 1080 product c693 (rev. 0x00)
[ 1.0000000] cypide0 at pci0 dev 7 function 1: Cypress 82C693 IDE Controller (rev. 0x00)
[ 1.0000000] cypide0: primary channel wired to compatibility mode
[ 1.0000000] cypide0: primary channel interrupting at isa irq 14
[ 1.0000000] atabus0 at cypide0 channel 0
[ 1.0000000] cypide1 at pci0 dev 7 function 2: Cypress 82C693 IDE Controller (rev. 0x00)
[ 1.0000000] cypide1: hardware does not support DMA
[ 1.0000000] cypide1: primary channel wired to compatibility mode
[ 1.0000000] cypide1: secondary channel interrupting at isa irq 15
[ 1.0000000] atabus1 at cypide1 channel 0
[ 1.0000000] vendor 1080 product c693 (USB serial bus, OHCI) at pci0 dev 7 function 3 not configured
[ 1.0000000] vga0 at pci0 dev 12 function 0: vendor 5333 product 8811 (rev. 0x00)
[ 1.0000000] wsdisplay0 at vga0 (kbdmux ignored)
[ 1.0000000] drm at vga0 not configured
[ 1.0000000] ppb0 at pci0 dev 20 function 0: vendor 1011 product 0024 (rev. 0x02)
[ 1.0000000] pci1 at ppb0 bus 1
[ 1.0000000] isa0 at sio0
[ 1.0000000] lpt0 at isa0 port 0x3bc-0x3bf irq 7
[ 1.0000000] com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
[ 1.0000000] com0: console
[ 1.0000000] com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
[ 1.0000000] pckbc0 at isa0 port 0x60-0x64
[ 1.0000000] fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
[ 1.0000000] mcclock0 at isa0 port 0x70-0x71: mc146818 compatible time-of-day clock
[ 1.0000000] stray isa irq 14
[ 1.1239962] stray isa irq 15
[ 4.0957795] fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
[ 5.0371902] wd0 at atabus0 drive 0
[ 5.0763950] wd0: <?>
[ 5.1065497] wd0: 16383 PB, 4151 cyl, 63 head, 12848 sec, 512 bytes/sect x 18446744072774503344 sectors
[ 5.2188295] atapibus0 at atabus1: 2 targets
[ 5.2696089] stray isa irq 15
[ 5.3194154] sd0 at atapibus0 drive 0: <\007\007x\003xx\000x, 0\000 6I HAD 02, \002> disk removable
[ 5.4453904] sd0(cypide1:0:0): Sense Error Code 0x64
[ 5.5023053] sd0: drive offline
[ 6.8604337] stray isa irq 14
[ 26.8917378] cypide0:0:0: geometry timed out
[ 26.9397306] wd0c: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), xfer 38, retry 0
[ 28.0440851] stray isa irq 14
[ 48.0753888] cypide0:0:0: geometry timed out
[ 48.1233752] wd0c: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), xfer 38, retry 1
[ 68.7238834] cypide0:0:0: geometry timed out
[ 68.7718769] wd0c: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), xfer 38, retry 2
I currently have a SATA-IDE bridge attached to the primary IDE interface and a standard IDE CD-ROM attached to the secondary IDE interface. I get similar issues with a standard IDE disk, specifically tested with a Seagate ST340016A 40GB drive.
Thanks!
- Alex