Hello,

I installed NetBSD on a UP1000　for the first time.
I found transfer error in dmesg, and Ultra-DMA mode 2 (Ultra/33) could 
not activate. I tried a new 80 pin short cable, but it was no go.
Do anyone have the same problem?
Is this a hardware problem, or software one?

Thank you in advance,

Best Regards,

Hiroshi

[ using 560896 bytes of netbsd ELF symbol table ]
consinit: not using prom console
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003
     The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
     The Regents of the University of California.  All rights reserved.

NetBSD 1.6.2_RC3 (GENERIC) #0: Sat Nov 29 22:19:16 JST 2003
     hako@eco-math20:/usr/src/sys/arch/alpha/compile/GENERIC
API UP1000 699 MHz, s/n
8192 byte page size, 1 processor.
total memory = 768 MB
(2728 KB reserved for PROM, 765 MB used by NetBSD)
avail memory = 704 MB
using 4910 buffers containing 39280 KB of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21264A-8
cpu0: Architecture extensions: 307<PAT,MVI,CIX,FIX,BWX>
irongate0 at mainbus0: AMD 751 Core Logic + AGP Chipset, rev. 37
agp0 at irongate0pci_mem_find: void region
: can't map aperture
pci0 at irongate0 bus 0
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
ppb0 at pci0 dev 1 function 0: Advanced Micro Devices AMD751 PCI-to-PCI 
Bridge (rev. 0x01)
pci1 at ppb0 bus 2
pci1: i/o space, memory space enabled
sio0 at pci0 dev 7 function 0: Acer Labs M1543 PCI-ISA Bridge (rev. 
0xc3)
vga0 at pci0 dev 8 function 0: 3D Labs GLINT Permedia 2V (rev. 0x01)
pci_mem_find: void region
pci_mem_find: void region
pci_mem_find: void region
wsdisplay0 at vga0 (kbdmux ignored): console (80x25, vt100 emulation)
tlp0 at pci0 dev 10 function 0: Lite-On 82C169 Ethernet, pass 2.1
tlp0: interrupting at isa irq 10
tlp0: Ethernet address 00:a0:cc:3a:ee:a6
lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 0
lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pciide0 at pci0 dev 16 function 0: Acer Labs M5229 UDMA IDE Controller 
(rev. 0xc1)
pciide0: bus-master DMA support present
pciide0: primary channel configured to compatibility mode
wd0 at pciide0 channel 0 drive 0: <IBM-DTLA-307030>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 29314 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 60036480 
sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd1 at pciide0 channel 0 drive 1: <IBM-DTLA-307030>
wd1: drive supports 16-sector PIO transfers, LBA addressing
wd1: 29314 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 60036480 
sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
pciide0: primary channel interrupting at isa irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using 
DMA data transfers)
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using 
DMA data transfers)
pciide0: secondary channel configured to compatibility mode
atapibus0 at pciide0 channel 1: 2 targets
cd0 at atapibus0 drive 1: <Pioneer CD-ROM ATAPI Model DR-944   010, , 
E1.07> type 5 cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
pciide0: secondary channel interrupting at isa irq 15
cd0(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using 
DMA data transfers)
Acer Labs M7101 Power Management Controller (miscellaneous prehistoric) 
at pci0 dev 17 function 0 not configured
isa0 at sio0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 (mux ignored): console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 (mux ignored)
lpt0 at isa0 port 0x3bc-0x3bf irq 7
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
spkr0 at pcppi0
isabeep0 at pcppi0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
Kernelized RAIDframe activated
root on wd0a dumps on wd0b
wd0: transfer error, downgrading to Ultra-DMA mode 1
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 1 (using DMA data 
transfers)
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using 
DMA data transfers)
wd0a: DMA error reading fsbn 16 of 16-31 (wd0 bn 16; cn 0 tn 0 sn 16), 
retrying
wd0: soft error (corrected)
root file system type: ffs
wd1: transfer error, downgrading to Ultra-DMA mode 1
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 1 (using DMA data 
transfers)
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 1 (using DMA data 
transfers)
wd1a: DMA error reading fsbn 16 of 16-31 (wd1 bn 16; cn 0 tn 0 sn 16), 
retrying
wd1: soft error (corrected)