Greetings.  I'm doing a new install of NetBSD 1.5.3 on to a Compaq DS10
"sarasvati".  All but the X installation sets were installed (from
sysinst). The first boot of NetBSD as installed hangs.

Here's how i got this far:

1) I netbooted the DS10  (via BOOTP and TFTP from a NetBSD
1.5.3 SPARC "brahma") using this file:
ftp://ftp.netbsd.org/pub/NetBSD/arch/alpha/netboot-1.5

2) Root was NFS mounted from the brahma.  The 1.5.3 kernel loaded was this
file:

ftp://ftp.netbsd.org/pub/NetBSD/NetBSD-1.5.3/alpha/installation/instkernel/netbsd.gz

 (gunzip'd into the file system that sarasvati NFS mounted on / )

 This worked well -- sysinst started automatically, and the new disk was
 partitioned, sets were selected, and everything installed.

For the output of the 1st boot after installation, see the attached.  The
boot really does stop right at "/etc/rc.conf is ".

I can hit the interrupt switch on the front of the DS10 and drop to the
SRM prompt, but i know very little about SRM, and am not sure how to get
anything useful out of it.  if it type "bpt" to invoke the console
debugger i get:

>>>bpt

Brk 0 at 001AB498

For comparison, i've also include the output from functional "boot ewa"
(netboot into sysinst). It's after my signature, the second set of
output. The first set of output below is the boot from disk that hangs.

Anyone have any ideas?


 -johan

>>>boot
(boot dka0.0.0.15.0 -flags a)
block 0 of dka0.0.0.15.0 is a valid boot block
reading 15 blocks from dka0.0.0.15.0
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 1e00
initializing HWRPB at 2000
initializing page table at 3ff46000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code

NetBSD/alpha 1.5.3 FFS Primary Bootstrap
Jumping to entry point...

NetBSD/alpha 1.5.3 Secondary Bootstrap, Revision 1.10
(he@albatross.urc.uninett.no, Jun 13 03:42:00 MEST 2002)

VMS PAL rev: 0x100420001014f
OSF PAL rev: 0x1003b00020148
Switch to OSF PAL code succeeded.

Boot flags: a
4723120+337024 [85+284904+167713]=0x542218

Entering netbsd at 0xfffffc00003010c0...
[ preserving 453608 bytes of netbsd ELF symbol table ]
consinit: not using prom console
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.5.3 (GENERIC) #59: Mon Jul  1 21:23:57 MEST 2002
    he@albatross.urc.uninett.no:/usr/src/sys/arch/alpha/compile/GENERIC
COMPAQ AlphaServer DS10 466 MHz
8192 byte page size, 1 processor.
total memory = 1024 MB
(2800 KB reserved for PROM, 1021 MB used by NetBSD)
avail memory = 943 MB
using 6548 buffers containing 52384 KB of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21264-4 (pass 3)
cpu0: Architecture extensions: 303<PAT,MVI,FIX,BWX>
tsc0 at mainbus0: 21272 Core Logic Chipset, Cchip rev 0
tsc0: 2 Dchips, 1 memory bus of 16 bytes
tsc0: arrays present: 512MB, 512MB, 0MB, 0MB, Dchip 0 rev 1
tsp0 at tsc0
pci0 at tsp0 bus 0
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
ohci0 at pci0 dev 1 function 0: Acer Labs M5237 USB Host Controller (rev. 0x03)
ohci0: interrupting at isa irq 10
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Acer Labs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
sio0 at pci0 dev 7 function 0: Acer Labs M1543 PCI-ISA Bridge (rev. 0xc3)
de0 at pci0 dev 9 function 0
de0: interrupting at dec 6600 irq 29
de0: DEC 21143 [10-100Mb/s] pass 4.1
de0: address 08:00:2b:86:77:93
de1 at pci0 dev 11 function 0
de1: interrupting at dec 6600 irq 30
de1: DEC 21143 [10-100Mb/s] pass 4.1
de1: address 08:00:2b:86:77:a8
de1: enabling 10baseT port
pciide0 at pci0 dev 13 function 0: Acer Labs M5229 UDMA IDE Controller (rev. 0xc1)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
pciide0: disabling primary channel (no drives)
pciide0: secondary channel wired to compatibility mode
atapibus0 at pciide0 channel 1
cd0 at atapibus0 drive 0: <COMPAQ  CDR-8435, , 0013> type 5 cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
pciide0: secondary channel interrupting at isa irq 15
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
siop0 at pci0 dev 15 function 0: Symbios Logic 53c895 (ultra2-wide scsi)
siop0: using on-board RAM
siop0: interrupting at dec 6600 irq 39
scsibus0 at siop0: 16 targets, 8 luns per target
isa0 at sio0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
lpt0 at isa0 port 0x3bc-0x3bf irq 7
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
isabeep0 at pcppi0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
stray isa irq 10
stray isa irq 10
stray isa irq 10
stray isa irq 10
stray isa irq 10; stopped logging
siop0: switching to single-ended mode
scsibus0: waiting 2 seconds for devices to settle...
siop0: target 0 using tagged queuing
sd0 at scsibus0 target 0 lun 0: <IBM, DDYS-T09170N, S93E> SCSI3 0/direct fixed
siop0: target 0 using 16bit transfers
siop0: target 0 now synchronous at 20.0Mhz, offset 31
sd0: 8748 MB, 15110 cyl, 3 head, 395 sec, 512 bytes/sect x 17916240 sectors
siop0: target 1 using tagged queuing
sd1 at scsibus0 target 1 lun 0: <IBM, DDYS-T09170N, S93E> SCSI3 0/direct fixed
siop0: target 1 using 16bit transfers
siop0: target 1 now synchronous at 20.0Mhz, offset 31
sd1: 8748 MB, 15110 cyl, 3 head, 395 sec, 512 bytes/sect x 17916240 sectors
de0: enabling 10baseT port
root on sd0a dumps on sd0b
root file system type: ffs
/etc/rc.conf is 

======================================================================
======================================================================

>>>boot ewa
(boot ewa0.0.0.9.0 -flags a)

Trying BOOTP boot.

Broadcasting BOOTP Request...
Received BOOTP Packet File Name is: //boot.netbsd.alpha
local inet address: 64.124.107.152
remote inet address: 64.124.107.153
TFTP Read File Name: //boot.netbsd.alpha
netmask = 255.0.0.0
Server is on same subnet as client.
.
bootstrap code read in
base = 200000, image_start = 0, image_bytes = efb0
initializing HWRPB at 2000
initializing page table at 3ff46000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code

NetBSD/alpha 1.5 Network Bootstrap, Revision 1.7
(root@frau-farbissina.shagadelic.org, Nov 22 01:41:53 PST 2000)

VMS PAL rev: 0x100420001014f
OSF PAL rev: 0x1003b00020148
Switch to OSF PAL code succeeded.

Boot flags: a
boot: ethernet address: 08:00:2b:86:77:93
boot: client addr: 64.124.107.152
boot: client name: sarasvati
boot: server addr: 64.124.107.153
boot: server path: /local/export/sarasvati/root
7826720+250640]=0x7b4388

Entering netbsd at 0xfffffc00003010c0...
[ netbsd ELF symbol table not valid ]
[ no symbol table formats found ]
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.5.3 (INSTALL) #38: Mon Jul  1 21:26:00 MEST 2002
    he@albatross.urc.uninett.no:/usr/src/sys/arch/alpha/compile/INSTALL
COMPAQ AlphaServer DS10 466 MHz
8192 byte page size, 1 processor.
total memory = 1024 MB
(2800 KB reserved for PROM, 1021 MB used by NetBSD)
avail memory = 940 MB
using 6548 buffers containing 52384 KB of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21264-4 (pass 3)
cpu0: Architecture extensions: 303<PAT,MVI,FIX,BWX>
tsc0 at mainbus0: 21272 Core Logic Chipset, Cchip rev 0
tsc0: 2 Dchips, 1 memory bus of 16 bytes
tsc0: arrays present: 512MB, 512MB, 0MB, 0MB, Dchip 0 rev 1
tsp0 at tsc0
pci0 at tsp0 bus 0
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
vendor 0x10b9 product 0x5237 (USB serial bus, interface 0x10, revision 0x03) at pci0 dev 1 function 0 not configured
sio0 at pci0 dev 7 function 0: vendor 0x10b9 product 0x1533 (rev. 0xc3)
de0 at pci0 dev 9 function 0
de0: interrupting at dec 6600 irq 29
de0: DEC 21143 [10-100Mb/s] pass 4.1
de0: address 08:00:2b:86:77:93
de1 at pci0 dev 11 function 0
de1: interrupting at dec 6600 irq 30
de1: DEC 21143 [10-100Mb/s] pass 4.1
de1: address 08:00:2b:86:77:a8
de1: enabling 10baseT port
pciide0 at pci0 dev 13 function 0: Acer Labs M5229 UDMA IDE Controller (rev. 0xc1)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
pciide0: disabling primary channel (no drives)
pciide0: secondary channel wired to compatibility mode
atapibus0 at pciide0 channel 1
cd0 at atapibus0 drive 0: <COMPAQ  CDR-8435, , 0013> type 5 cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
pciide0: secondary channel interrupting at isa irq 15
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
siop0 at pci0 dev 15 function 0: Symbios Logic 53c895 (ultra2-wide scsi)
siop0: using on-board RAM
siop0: interrupting at dec 6600 irq 39
scsibus0 at siop0: 16 targets, 8 luns per target
isa0 at sio0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
lpt0 at isa0 port 0x3bc-0x3bf irq 7
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
siop0: switching to single-ended mode
scsibus0: waiting 2 seconds for devices to settle...
siop0: target 0 using tagged queuing
sd0 at scsibus0 target 0 lun 0: <IBM, DDYS-T09170N, S93E> SCSI3 0/direct fixed
siop0: target 0 using 16bit transfers
siop0: target 0 now synchronous at 20.0Mhz, offset 31
sd0: 8748 MB, 15110 cyl, 3 head, 395 sec, 512 bytes/sect x 17916240 sectors
siop0: target 1 using tagged queuing
sd1 at scsibus0 target 1 lun 0: <IBM, DDYS-T09170N, S93E> SCSI3 0/direct fixed
siop0: target 1 using 16bit transfers
siop0: target 1 now synchronous at 20.0Mhz, offset 31
sd1: 8748 MB, 15110 cyl, 3 head, 395 sec, 512 bytes/sect x 17916240 sectors
de0: enabling 10baseT port
md0: internal 4650K image area
root on md0a dumps on md0b
WARNING: clock gained 33 days -- CHECK AND RESET THE DATE!
root file system type: ffs
Terminal type? [vt100]