I'm interested in putting an Adaptec 1542CF in my PC64-275 under NetBSD
1.5.2 (well...the latest snapshot, actually).  Doesn't seem to work with my
GENERIC kernel.  FWIW...there is an ISA WD Ethernet card that does seem to
work in this box.  I've not diddled with ISACFG, as I can't seem to find the 
apropos doco. 

I've tried it at 0x330 & 0x334, with & without BIOS enabled.  The LED on the 
card gives a steady, 1Hz blink. 

Any clues? 

FWIW...here is a dmesg. 

pc64# dmesg
[ using 513576 bytes of netbsd ELF symbol table ]
consinit: not using prom console
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001
  The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
  The Regents of the University of California.  All rights reserved. 

NetBSD 1.5Y (GENERIC) #2: Thu Nov  1 15:41:54 EST 2001
  root@pc64.seefried.com:/export/NetBSD/src/sys/arch/alpha/compile/GENERIC
Digital AlphaPC 64 274 MHz, s/n
8192 byte page size, 1 processor.
total memory = 320 MB
(2040 KB reserved for PROM, 318 MB used by NetBSD)
avail memory = 289 MB
using 2048 buffers containing 16384 KB of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21064A-2
apecs0 at mainbus0: DECchip 21072 Core Logic chipset
apecs0: DC21071-CA pass 2, 128-bit memory bus
apecs0: DC21071-DA pass 2
pci0 at apecs0 bus 0
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
de0 at pci0 dev 5 function 0
de0: interrupting at eb64+ irq 2
de0: 21140A [10-100Mb/s] pass 2.2
de0: address 00:40:05:a3:41:ed
vga0 at pci0 dev 7 function 0: S3 Trio32/64 (rev. 0x54)
wsdisplay0 at vga0: console (80x25, vt100 emulation)
sio0 at pci0 dev 8 function 0: Intel 82378ZB System I/O (SIO) (rev. 0x84)
siop0 at pci0 dev 9 function 0: Symbios Logic 53c825 (fast wide scsi)
siop0: interrupting at eb64+ irq 3
scsibus0 at siop0: 16 targets, 8 luns per target
isa0 at sio0
depca: address not found
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0
wdc0 at isa0 port 0x1f0-0x1f7 irq 14
wd0 at wdc0 channel 0 drive 0: <WDC AC310100B>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 9671 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 19807200 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
we1 at isa0 port 0x300-0x31f iomem 0xcc000-0xcffff irq 10
we1: WD8013WC Ethernet (16-bit)
we1: Ethernet address 00:00:c0:28:8c:47
lpt0 at isa0 port 0x3bc-0x3bf irq 7
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
spkr0 at pcppi0
isabeep0 at pcppi0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <SEAGATE, ST31200W SUN1.05, 8724> SCSI2
0/direct fixed
sd0: 1006 MB, 2700 cyl, 9 head, 84 sec, 512 bytes/sect x 2061108 sectors
sd0: sync (100.0ns offset 8), 16-bit (20.000MB/s) transfers, tagged queueing
cd0 at scsibus0 target 5 lun 0: <PLEXTOR, CD-ROM PX-8XCS, 7t02> SCSI2
5/cdrom removable
cd0: sync (100.0ns offset 8), 8-bit (10.000MB/s) transfers
root on sd0a dumps on sd0b
root file system type: ffs
de0: autosense failed: cable problem?
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
pc64#