I'm having some trouble with keyboard locking up while booting.  The
keyboard works fine at the boot prompt.

This is on NetBSD-1.5 - dmesg included below.

The problem is intermitent and not reproducable.

Do some of your patches address this problem?
johnh...

> On Sun, 14 Jan 2001, Juergen Weiss wrote:
> 
> > Date: Sun, 14 Jan 2001 15:59:26 +0100 (MET)
> > From: Juergen Weiss <weiss@Uni-Mainz.DE>
> > To: John Hayward <John.C.Hayward@wheaton.edu>
> > Subject: Re: X Video Modes - Multia
> > 
> > 
> > 
> > I posted the following diffs a while ago. They fix various
> > problems on the multia, including your X problem.
...
dmesg below:
-----------------
[ preserving 220696 bytes of netbsd ELF symbol table ]
Copyright (c) 1996, 1997, 1998, 1999, 2000
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.5 (MULTIMA $) #7: Fri Jan 15 21:48:53 CST 2021
    johnh@alpha:/usr/src/sys/arch/alpha/compile/MULTIMA
(PCI ISA), 167MHz
8192 byte page size, 1 processor.
total memory = 24576 KB
(2296 KB reserved for PROM, 22280 KB used by NetBSD)
avail memory = 17800 KB
using 152 buffers containing 1216 KB of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), LCA-2 (21066 pass 2)
cpu0: VAX FP support, IEEE FP support, Primary Eligible
lca0 at mainbus0
pci0 at lca0 bus 0
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
siop0 at pci0 dev 6 function 0: Symbios Logic 53c810 (fast scsi)
siop0: interrupting at isa irq 11
scsibus0 at siop0: 8 targets, 8 luns per target
sio0 at pci0 dev 7 function 0: Intel 82378ZB System I/O (SIO) (rev. 0x03)
de0 at pci0 dev 8 function 0
de0: interrupting at isa irq 14
de0: DEC 21040 [10Mb/s] pass 2.3
de0: address 08:00:2b:e4:42:8b
unknown vendor 0x0001 product 0x0000 (miscellaneous prehistoric, revision
0x01)
at pci0 dev 9 function 0 not configured
tga0 at pci0 dev 11 function 0: DC21030 step B, board type T8-02
tga0: 1024 x 768, 8bpp, Bt485 RAMDAC
tga0: interrupting at isa irq 10
wsdisplay0 at tga0: console (std, vt100 emulation)
isa0 at sio0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0
lpt0 at isa0 port 0x3bc-0x3bf irq 7
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
isabeep0 at pcppi0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
stray isa irq 3
stray isa irq 4
scsibus0: waiting 2 seconds for devices to settle...
de0: enabling 10baseT port
sd0 at scsibus0 target 6 lun 0: <SEAGATE, ST15230W SUN4.2G, 0738> SCSI2 0/direct
 fixed
siop0: target 6 now synchronous at 10.0Mhz, offset 8
sd0: 4095 MB, 3992 cyl, 19 head, 110 sec, 512 bytes/sect x 8386733 sectors
root on sd0a dumps on sd0b
readclock: 21/1/16/4/5/32=>1610769932 (1610769086)
init: copying out flags `-s' 3
init: copying out path `/sbin/init' 11
------------------------------