1.4's sysinst seems to think I have a 1MB disk, but it's about 1GB larger
than that.  I'm installing on sd1, sd0 is DU 4.0D.  Where does it think
it's getting this info, and how do I fix it?

I booted off of sd1, using the diskimage... so it is using the disklabel
from that to decide it is a 1MB disk?  I'd think that's not the desired
behavior.

# cat /kern/msgbuf
Copyright (c) 1996, 1997, 1998, 1999
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.4 (INSTALL) #1: Sat May  8 11:40:47 PDT 1999
    ross@netbsd.org:/usr/src/sys/arch/alpha/compile/INSTALL
AlphaStation 200 4/166, 166MHz
8192 byte page size, 1 processor.
real mem = 33554432 (2048000 reserved for PROM, 31506432 used by NetBSD)
avail mem = 21954560
using 384 buffers containing 3145728 bytes of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21064A ()
apecs0 at mainbus0: DECchip 21071 Core Logic chipset
apecs0: DC21071-CA pass 2, 64-bit memory bus
apecs0: DC21071-DA pass 2
pci0 at apecs0 bus 0
pci0: i/o enabled, memory enabled
ncr0 at pci0 dev 6 function 0: ncr 53c810 fast10 scsi
ncr0: interrupting at isa irq 11
ncr0: minsync=25, maxsync=206, maxoffs=8, 16 dwords burst, normal dma fifo
ncr0: single-ended, open drain IRQ driver
ncr0: restart (scsi reset).
scsibus0 at ncr0: 8 targets, 8 luns per target
sd0 at scsibus0 targ 0 lun 0: <DEC, RZ26F    (C) DEC, 630J> SCSI2 0/direct fixed
sd0(ncr0:0:0): 10.0 MB/s (100 ns, offset 8)
sd0: 1001MB, 3117 cyl, 8 head, 82 sec, 512 bytes/sect x 2050860 sectors
sd1 at scsibus0 targ 1 lun 0: <DEC, RZ26F    (C) DEC, 630J> SCSI2 0/direct fixed
sd1(ncr0:1:0): 10.0 MB/s (100 ns, offset 8)
sd1: 1001MB, 3117 cyl, 8 head, 82 sec, 512 bytes/sect x 2050860 sectors
cd0 at scsibus0 targ 4 lun 0: <DEC, RRD46   (C) DEC, 0557> SCSI2 5/cdrom removable
probe(ncr0:4:1): 10.0 MB/s (100 ns, offset 8)
sio0 at pci0 dev 7 function 0: vendor 0x8086 product 0x0484 (rev. 0x43)
de0 at pci0 dev 11 function 0
de0: interrupting at isa irq 5
de0: DEC 21040 [10Mb/s] pass 2.4
de0: address 00:00:f8:23:5a:1c
tga0 at pci0 dev 13 function 0: DC21030 step C, board type T32-88
tga0: 1280 x 1024, 32bpp, Bt463 RAMDAC
tga0: interrupting at isa irq 10
wsdisplay0 at tga0
isa0 at sio0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
lpt0 at isa0 port 0x3bc-0x3bf irq 7
pckbc0 at isa0 port 0x60-0x64
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
md0: internal 3072K image area
root on md0a dumps on md0b
WARNING: preposterous clock chip time
 -- CHECK AND RESET THE DATE!
root file system type: ffs
de0: enabling 10baseT port

Tracy J. Di Marco White
Project Vincent Systems Manager
gendalia@iastate.edu