Subject: eek, isp crash
To: None <port-alpha@netbsd.org>
From: Sean Doran <smd@ebone.net>
List: port-alpha
Date: 03/11/1999 00:11:37
What does oen make of this?

isp0: isp_control MBOX_ABORT failure (code 4001)
isp0: isp_watch failed to abort command
isp0: Ultra Mode Capable
isp0: Board Revision 1040B, loaded F/W Revision 7.55
isp0: Last F/W revision was 5.57
isp0: transport error
states->GOT_BUS GOT_TGT SENT_CDB 
status->Disconnect 
isp0: isp_mboxcmd timeout #2
isp0: isp_control MBOX_ABORT failure (code 0)
isp0: isp_watch failed to abort command
isp0: Ultra Mode Capable
isp0: Board Revision 1040B, loaded F/W Revision 7.55
isp0: Last F/W revision was 5.57
isp0: timeout initiated SCSI bus reset
isp0: command for target 3 lun 0 was aborted
isp0: command aborted for target 3 lun 0
isp0: isp_mboxcmd timeout #2
isp0: isp_control MBOX_ABORT failure (code 0)
isp0: isp_watch failed to abort command
isp0: Ultra Mode Capable
isp0: Board Revision 1040B, loaded F/W Revision 7.55
isp0: Last F/W revision was 5.57
isp0: isp_mboxcmd timeout #2
isp0: failed to set initiator id
    biu_conf1=34 biu_icr=6 biu_isr=0 biu_sema=0 risc_hccr=80
    cdma_conf=0 cdma_sts=8 cdma_fifostat=0
    ddma_conf=0 ddma_sts=2108 ddma_fifostat=288
    sxp_int=0 sxp_gross=4d00 sxp(scsi_ctrl)=6eac
    mbox regs: 4000 7 37 0 7
isp0: PCI Status Command/Status=2000157
isp0: isp_restart cannot restart ISP
isp0: adapter not ready
isp0: adapter not ready
isp0: adapter not ready
isp0: adapter not ready
isp0: async 4001
isp0: adapter not ready
isp0: adapter not ready
isp0: adapter not ready
isp0: adapter not ready

subsequent boot messages:

isp0: adapter not ready
isp0úff.fe.fd.fc.fb.fa.f9.f8.f7.f6.f5.
ef.df.ee.ed.ec.f4.eb.ea.e9.e8.e7.e6.....e5.
V6.9-4, built on Oct 12 1998 at 11:22:55
>>>boot -fl i
(boot dkb300.3.0.13.0 -file netbsd -flags i)
block 0 of dkb300.3.0.13.0 is a valid boot block
reading 15 blocks from dkb300.3.0.13.0
bootstrap code read in
base = 1f2000, image_start = 0, image_bytes = 1e00
initializing HWRPB at 2000
initializing page table at 1e4000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code

NetBSD/Alpha 1.3I Primary Boot +

.
Jumping to entry point...

NetBSD/Alpha Secondary Boot, Revision 1.9
(smd@alfa.smd.ebone.net, Fri Mar  5 02:26:37 CET 1999)

VMS PAL rev: 0x1000000010538
OSF PAL rev: 0x100000002012e
Switch to OSF PAL code succeeded.

Boot file: netbsd
Boot flags: i
Boot file: 

Loading netbsd...
1577192+307800 [85+106560+55809]

Entering netbsd at 0xfffffc0000301050...
Unrecognized boot flag 'i'.
[ preserving 163360 bytes of netbsd ELF symbol table ]
Copyright (c) 1996, 1997, 1998, 1999
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.3K (SMDALFA) #0: Thu Mar  4 19:21:53 CET 1999
    smd@alfa.smd.ebone.net:/usr/src/sys/arch/alpha/compile/SMDALFA
AlphaStation 200 4/233, 233MHz
8192 byte page size, 1 processor.
real mem = 83886080 (2048000 reserved for PROM, 81838080 used by NetBSD)
avail mem = 69484544
using 999 buffers containing 8183808 bytes of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21064A ()
apecs0 at mainbus0: DECchip 21071 Core Logic chipset
apecs0: DC21071-CA pass 2, 64-bit memory bus
apecs0: DC21071-DA pass 2
pci0 at apecs0 bus 0
pci0: i/o enabled, memory enabled
ncr0 at pci0 dev 6 function 0: ncr 53c810 fast10 scsi
ncr0: interrupting at isa irq 11
ncr0: minsync=25, maxsync=206, maxoffs=8, 16 dwords burst, normal dma fifo
ncr0: single-ended, open drain IRQ driver
ncr0: restart (scsi reset).
scsibus0 at ncr0: 8 targets, 8 luns per target
sio0 at pci0 dev 7 function 0: Intel 82378ZB System I/O (SIO) (rev. 0x84)
de0 at pci0 dev 11 function 0
de0: interrupting at isa irq 5
de0: DEC 21040 [10Mb/s] pass 2.4
de0: address 00:00:f8:21:68:c6
isp0 at pci0 dev 13 function 0
isp0: Ultra Mode Capable
isp0: Board Revision 1040B, loaded F/W Revision 7.55
isp0: Last F/W revision was 5.57
isp0: interrupting at isa irq 10
isp0: driver initiated bus reset
scsibus1 at isp0: 16 targets, 8 luns per target
sd0 at scsibus1 targ 3 lun 0: <SEAGATE, ST15230W SUN4.2G, 0738> SCSI2 0/direct fixed
sd0: 4095MB, 3992 cyl, 19 head, 110 sec, 512 bytes/sect x 8386733 sectors
isa0 at sio0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
lpt0 at isa0 port 0x3bc-0x3bf irq 7
wss0 at isa0 port 0x530-0x537 irq 9 drq 0: CS4231A
audio0 at wss0: half duplex
pcppi0 at isa0 port 0x61
isabeep0 at pcppi0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
root on sd0a dumps on sd0b
isp0: Target 3 at 10MHz Max Offset 8, 16 bit wide, Tagged Queueing Enabled
WARNING: clock gained 4 days -- CHECK AND RESET THE DATE!
de0: enabling 10baseT port
Enter pathname of shell or RETURN for sh: