This is a multi-part message in MIME format.

--Boundary_(ID_TZbTifqgyWkxB3dh6P9Fww)
Content-type: text/plain; charset=ISO-8859-1; format=flowed
Content-transfer-encoding: 7BIT

Hello,

I installed NetBSD 3.0 on a laptop but I've hit a wall trying to get the
OS to recognize my wireless card. I have a Compaq W110 card that I
*think* is compatible with the wi driver, but I've tried a different
type of card and I get the same messages regardless. During boot and
whenever I insert the card I receive the following messages:

cbb0: wait took 0.008594s
pcmcia0: ++enabled_count = 1
cis mem map cb0ae000
pcmcia0: CIS tuple chain:
   ff
CISTPL_END
cis mem map cb0ae000
CISTPL_LINKTARGET expected, code ff observed
pcmcia0: card appears to have bogus CIS
pcmcia0: --enabled_count = 0

I've attached my complete dmesg output. I'm running the GENERIC_LAPTOP
kernel slightly modified for more verbose debugging information. Does
anyone have any suggestions as to how I could get this to work?

Thank you very much,

Jonathan Voris





--Boundary_(ID_TZbTifqgyWkxB3dh6P9Fww)
Content-type: text/plain; name=dmesg.txt
Content-transfer-encoding: 7BIT
Content-disposition: inline; filename=dmesg.txt

NetBSD 3.0 (TECHNODROME) #2: Fri Apr 21 21:55:49 EDT 2006
	jvoris@technodrome:/usr/src/sys/arch/i386/compile/TECHNODROME
total memory = 383 MB
avail memory = 368 MB
BIOS32 rev. 0 found at 0xf0000
PCI BIOS rev. 2.1 found at 0xf0478
pcibios: config mechanism [1][x], special cycles [x][x], last bus 1
PCI IRQ Routing Table rev. 1.0 found at 0xf0970, size 0 bytes (-2 entries)
pcibios_pir_init: bad IRQ table size
PCI IRQ Routing Table rev. 1.0 found at 0xf9c70, size 224 bytes (12 entries)
PCI Interrupt Router at 000:07:0 (Intel 82371AB (PIIX4) PCI-ISA Bridge compatible)
PCI Exclusive IRQs: 11
------------------------------------------
  device vendor product pin PIRQ IRQ stage
------------------------------------------
000:04:0 0x104c 0xac1c   A  0x00  11  0    already assigned
000:04:1 0x104c 0xac1c   A  0x00  11  0    already assigned
000:07:2 0x8086 0x7112   D  0x03  11  0    already assigned
000:08:0 0x125d 0x1978   A  0x02  11  0    already assigned
000:09:0 0x8086 0x1229   A  0x02  11  0    already assigned
000:09:1 0x11c1 0x0445   A  0x02  11  0    already assigned
001:00:0 0x1002 0x4c4d   A  0x00  11  0    already assigned
------------------------------------------
PCI fixup examining 8086:7190
PCI fixup examining 8086:7191
PCI fixup examining 1002:4c4d
PCI bridge 0: primary 0, secondary 1, subordinate 1
PCI fixup examining 104c:ac1c
PCI bridge 1: primary 0, secondary 2, subordinate 2
PCI fixup examining 104c:ac1c
PCI bridge 2: primary 0, secondary 3, subordinate 3
PCI fixup examining 8086:7110
PCI fixup examining 8086:7111
PCI fixup examining 8086:7112
PCI fixup examining 8086:7113
PCI fixup examining 125d:1978
PCI fixup examining 8086:1229
PCI fixup examining 11c1:445
PCI bus #3 is the last bus
[System BIOS Setting]-----------------------
  device vendor product
  register space address    size
--------------------------------------------
000:00:0 0x8086 0x7190 
	10h mem  0x50000000 0x04000000
		[OK]
000:01:0 0x8086 0x7191 
		[OK]
000:04:0 0x104c 0xac1c 
	10h mem  0x41180000 0x00001000
		[OK]
000:04:1 0x104c 0xac1c 
	10h mem  0x41200000 0x00001000
		[OK]
000:07:0 0x8086 0x7110 
		[OK]
000:07:1 0x8086 0x7111 
	20h port 0x00003460 0x00000010
		[OK]
000:07:2 0x8086 0x7112 
	20h port 0x00003440 0x00000020
		[OK]
000:07:3 0x8086 0x7113 
		[OK]
000:08:0 0x125d 0x1978 
	10h port 0x00003000 0x00000100
		[OK]
000:09:0 0x8086 0x1229 
	10h mem  0x41280000 0x00001000
	14h port 0x00003400 0x00000040
	18h mem  0x41100000 0x00020000
		[OK]
000:09:1 0x11c1 0x0445 
	10h port 0x00003470 0x00000008
	14h mem  0x41300000 0x00001000
		[OK]
001:00:0 0x1002 0x4c4d 
	10h mem  0x40000000 0x01000000
	14h port 0x00002000 0x00000100
	18h mem  0x41000000 0x00001000
		[OK]
--------------------------[  0 devices bogus]
 Physical memory end: 0x17fec000
 PCI memory mapped I/O space start: 0x18000000
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium III (686-class), 896.14 MHz, id 0x68a
cpu0: features 383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR>
cpu0: features 383f9ff<PGE,MCA,CMOV,PAT,PSE36,MMX>
cpu0: features 383f9ff<FXSR,SSE>
cpu0: I-cache 16 KB 32B/line 4-way, D-cache 16 KB 32B/line 4-way
cpu0: L2 cache 256 KB 32B/line 8-way
cpu0: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: 8 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82443BX Host Bridge/Controller (rev. 0x03)
agp0 at pchb0: aperture at 0x50000000, size 0x4000000
ppb0 at pci0 dev 1 function 0: Intel 82443BX AGP Interface (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: ATI Technologies Rage Mobility (rev. 0x64)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
cbb0 at pci0 dev 4 function 0: Texas Instruments PCI1225 PCI-CardBus Bridge (rev. 0x01)
cbb1 at pci0 dev 4 function 1: Texas Instruments PCI1225 PCI-CardBus Bridge (rev. 0x01)
pcib0 at pci0 dev 7 function 0
pcib0: Intel 82371AB (PIIX4) PCI-ISA Bridge (rev. 0x02)
piixide0 at pci0 dev 7 function 1
piixide0: Intel 82371AB IDE controller (PIIX4) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel ignored (disabled)
uhci0 at pci0 dev 7 function 2: Intel 82371AB (PIIX4) USB Host Controller (rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Intel 82371AB (PIIX4) Power Management Controller (miscellaneous bridge, revision 0x03) at pci0 dev 7 function 3 not configured
esm0 at pci0 dev 8 function 0: ESS Technology Maestro 2E PCI Audio Accelerator (rev. 0x10)
esm0: interrupting at irq 11
esm0: ac97: SigmaTel STAC9721/23 codec; 18 bit DAC, 18 bit ADC, SigmaTel 3D
audio0 at esm0: full duplex, mmap, independent
fxp0 at pci0 dev 9 function 0: i82559S Ethernet, rev 9
fxp0: interrupting at irq 11
fxp0: Ethernet address 00:d0:59:4c:11:c3
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Lucent Technologies LTMODEM (serial communications) at pci0 dev 9 function 1 not configured
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2 device 0
pcmcia0 at cardslot0
cbb1: interrupting at irq 11
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 3 device 0
pcmcia1 at cardslot1
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com2 at isa0 port 0x3e8-0x3ef irq 5: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pms0: Synaptics touchpad version 5.6
pms0: Palm detect, Multi-finger
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
apm0 at mainbus0: Power Management spec V1.2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
Kernelized RAIDframe activated
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 1: <Compaq  DVD-ROM SD-C2402, 5100706747, 1A05> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
wd0 at atabus0 drive 0: <HITACHI_DK23CA-20>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 19077 MB, 38760 cyl, 16 head, 63 sec, 512 bytes/sect x 39070080 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
cd0(piixide0:0:1): using PIO mode 4, DMA mode 2 (using DMA)
cbb0: wait took 0.009115s
pcmcia0: ++enabled_count = 1
cis mem map cb095000
pcmcia0: CIS tuple chain:
 ff
CISTPL_END
cis mem map cb095000
CISTPL_LINKTARGET expected, code ff observed
pcmcia0: card appears to have bogus CIS
pcmcia0: --enabled_count = 0
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)



--Boundary_(ID_TZbTifqgyWkxB3dh6P9Fww)--