On 1/4/06 2:46 PM, "Manuel Bouyer" <bouyer@antioche.eu.org> wrote:
...
> But from your previous dmesg I see that you were running a MP kernel,
> did you try 3.0 GENERIC.MP ? It looks like the MP bios table has the
> correct information about the secondary channel interrupt.

That was it.  Getting the kernel on there was a sincere pain as the cdrom
drive refused to work under 3.0.  (Seemingly an ata controller issue which
I'll doco in a pr when I have sufficient info).

Thank you very much Manuel!

NetBSD 3.0 (GENERIC.MP) #4: Tue Dec 27 11:57:19 CST 2005
        
peter@buster:/builds/netbsd-3/i386/obj/builds/netbsd-3/src/sys/arch/i386/com
pile/GENERIC.MP
total memory = 1279 MB
avail memory = 1242 MB
BIOS32 rev. 0 found at 0xf0000
mainbus0 (root)
mainbus0: Intel MP Specification (Version 1.4) (COMPAQ   PROLIANT    )
cpu0 at mainbus0: apid 1 (boot processor)
cpu0: Intel Pentium III Xeon (686-class), 797.53 MHz, id 0x683
cpu0: features 383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features 383fbff<PGE,MCA,CMOV,PAT,PSE36,MMX>
cpu0: features 383fbff<FXSR,SSE>
cpu0: I-cache 16 KB 32B/line 4-way, D-cache 16 KB 32B/line 4-way
cpu0: L2 cache 256 KB 32B/line 8-way
cpu0: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: calibrating local timer
cpu0: apic clock running at 132 MHz
cpu0: 8 page colors
cpu1 at mainbus0: apid 0 (application processor)
cpu1: starting
cpu1: Intel Pentium III Xeon (686-class), 797.48 MHz, id 0x683
cpu1: features 383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu1: features 383fbff<PGE,MCA,CMOV,PAT,PSE36,MMX>
cpu1: features 383fbff<FXSR,SSE>
cpu1: I-cache 16 KB 32B/line 4-way, D-cache 16 KB 32B/line 4-way
cpu1: L2 cache 256 KB 32B/line 8-way
cpu1: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu1: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
mpbios: bus 0 is type PCI
mpbios: bus 2 is type PCI
mpbios: bus 5 is type PCI
mpbios: bus 15 is type ISA
ioapic0 at mainbus0 apid 8 (I/O APIC)
ioapic0: pa 0xfec00000, version 11, 35 pins
ioapic0: misconfigured as apic 0
ioapic0: remapped to apic 8
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: ServerWorks CNB20-HE PCI/AGP bridge (rev. 0x06)
pchb1 at pci0 dev 0 function 1
pchb1: ServerWorks CNB20-HE PCI/AGP bridge (rev. 0x06)
pci1 at pchb1 bus 2
pci1: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
cac0 at pci1 dev 6 function 0: Compaq Smart Array 431
cac0: interrupting at ioapic0 pin 24 (irq 10)
ld0 at cac0 unit 0: standalone disk or RAID0 array
ld0: 8670 MB, 4403 cyl, 64 head, 63 sec, 512 bytes/sect x 17756160 sectors
Compaq Advanced Systems Management Controller (miscellaneous system) at pci0
dev 3 function 0 not configured
vga1 at pci0 dev 5 function 0: ATI Technologies 3D Rage IIC (rev. 0x7a)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
fxp0 at pci0 dev 8 function 0: Intel i82557 Ethernet, rev 2
fxp0: interrupting at ioapic0 pin 31 (irq 5)
fxp0: May need receiver lock-up workaround
fxp0: Ethernet address 00:60:b0:67:24:9f
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 15 function 0
pcib0: ServerWorks OSB4 southbridge (rev. 0x4f)
rccide0 at pci0 dev 15 function 1
rccide0: ServerWorks OSB4 IDE Controller (rev. 0x00)
rccide0: bus-master DMA support present
rccide0: primary channel configured to compatibility mode
rccide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus0 at rccide0 channel 0
rccide0: secondary channel configured to compatibility mode
isa_intr_establish: no MP mapping found
rccide0: secondary channel interrupting at irq 15
atabus1 at rccide0 channel 1
pchb2 at pci0 dev 17 function 0
pchb2: ServerWorks CNB20-HE PCI/AGP bridge (rev. 0x06)
pci2 at pchb2 bus 255
pci2: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb3 at pci0 dev 17 function 1
pchb3: ServerWorks CNB20-HE PCI/AGP bridge (rev. 0x06)
pci3 at pchb3 bus 5
pci3: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
esiop0 at pci3 dev 4 function 0: Symbios Logic 53c896 (ultra2-wide scsi)
esiop0: using on-board RAM
esiop0: interrupting at ioapic0 pin 22 (irq 11)
scsibus0 at esiop0: 16 targets, 8 luns per target
esiop1 at pci3 dev 4 function 1: Symbios Logic 53c896 (ultra2-wide scsi)
esiop1: using on-board RAM
esiop1: interrupting at ioapic0 pin 21 (irq 15)
scsibus1 at esiop1: 16 targets, 8 luns per target
ahc1 at pci3 dev 5 function 0: Adaptec 29160 Ultra160 SCSI adapter
ahc1: interrupting at ioapic0 pin 26 (irq 15)
ahc1: aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsibus2 at ahc1: 16 targets, 8 luns per target
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
ioapic0: enabling
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
Kernelized RAIDframe activated
atapibus0 at atabus0: 2 targets
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
scsibus2: waiting 2 seconds for devices to settle...
cd0 at atapibus0 drive 0: <COMPAQ XM-6402B, , 1723> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(rccide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
(using DMA)
sd0 at scsibus2 target 0 lun 0: <IFT, 3102, 0223> disk fixed
sd0: 52098 MB, 52098 cyl, 64 head, 32 sec, 512 bytes/sect x 106698624
sectors
sd0: sync (50.00ns offset 16), 16-bit (40.000MB/s) transfers, tagged
queueing
boot device: ld0
root on ld0a dumps on ld0b
root file system type: ffs
cpu1: CPU 0 running
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
---

peter