Is there a USB hard drive howto?

I just bought an ADS USB/Firewire external drive enclosure (and put a Seagate 80GB drive in it). The relevant dmesg output is as follows (complete is below).

 NetBSD 1.6 (GENERIC) #0: Sun Sep  8 19:43:40 UTC 2002
    autobuild@tgm.daemon.org:/autobuild/i386/OBJ/autobuild/src/sys/arch/i386/compile/GENERIC
 uhci0 at pci0 dev 7 function 2: Intel 82371AB USB Host Controller (PIIX4) (rev. 0x01)
 uhci0: interrupting at irq 11

 usb0 at uhci0: USB revision 1.0
 uhub0 at usb0
 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub0: 2 ports with 2 removable, self powered

 umass0 at uhub0 port 1 configuration 1 interface 0
 umass0: ADS Technologies lnc. USB2.0 Storage Device, rev 2.00/0.01, addr 2
 umass0: using SCSI over Bulk-Only

So how do I mount the drive? I've seen other posts that indicate that the drive shows up as a sdXX or a wdXX, but I have no such message in my dmesg.

Help!

Thanks in advance,


--
Brian



entire dmesg output

====================

NetBSD 1.6 (GENERIC) #0: Sun Sep  8 19:43:40 UTC 2002
    autobuild@tgm.daemon.org:/autobuild/i386/OBJ/autobuild/src/sys/arch/i386/compile/GENERIC
cpu0: Intel OverDrive Pentium/MMX (586-class), 200.46 MHz
cpu0: features 8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
cpu0: features 8001bf<MMX>
total memory = 191 MB
avail memory = 171 MB
using 2478 buffers containing 9912 KB of memory
BIOS32 rev. 0 found at 0xfb310
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82439TX System Controller (MTXC) (rev. 0x01)
pcib0 at pci0 dev 7 function 0
pcib0: Intel 82371AB PCI-to-ISA Bridge (PIIX4) (rev. 0x01)
pciide0 at pci0 dev 7 function 1: Intel 82371AB IDE controller (PIIX4) (rev. 0x01)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
wd0 at pciide0 channel 0 drive 0: <ST34323A>
wd0: drive supports 32-sector PIO transfers, LBA addressing
wd0: 4112 MB, 8912 cyl, 15 head, 63 sec, 512 bytes/sect x 8421840 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
wd1 at pciide0 channel 0 drive 1: <Maxtor 90840D6>
wd1: drive supports 16-sector PIO transfers, LBA addressing
wd1: 8010 MB, 16276 cyl, 16 head, 63 sec, 512 bytes/sect x 16406208 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
pciide0: secondary channel wired to compatibility mode
atapibus0 at pciide0 channel 1: 2 targets
cd0 at atapibus0 drive 1: <PCRW1208, , 12> type 5 cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
wd2 at pciide0 channel 1 drive 0: <MAXTOR 4K080H4>
wd2: drive supports 16-sector PIO transfers, LBA addressing
wd2: 76319 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd2: 32-bit data port
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
pciide0: secondary channel interrupting at irq 15
wd2(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
cd0(pciide0:1:1): using PIO mode 4, DMA mode 2 (using DMA data transfers)
uhci0 at pci0 dev 7 function 2: Intel 82371AB USB Host Controller (PIIX4) (rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Intel 82371AB Power Management Controller (PIIX4) (miscellaneous bridge, revision 0x01) at pci0 dev 7 function 3 not configured
tlp0 at pci0 dev 13 function 0: Lite-On 82C169 Ethernet, pass 2.0
tlp0: interrupting at irq 11
tlp0: Ethernet address 00:a0:cc:20:56:d7
ukphy0 at tlp0 phy 1: Generic IEEE 802.3u media interface
ukphy0: MTD972 10/100 media interface (OUI 0x00032d, model 0x0000), rev. 8
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vga1 at pci0 dev 15 function 0: Matrox MGA Millennium II 2164W (rev. 0x00)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
adv1 at pci0 dev 16 function 0: AdvanSys ABP-9xxU SCSI adapter
adv1: interrupting at irq 10
scsibus0 at adv1: 8 targets, 8 luns per target
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
biomask ef65 netmask ef65 ttymask ffe7
scsibus0: waiting 2 seconds for devices to settle...
Kernelized RAIDframe activated
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
pciide0:0:0: lost interrupt
	type: ata tc_bcount: 8192 tc_skip: 0
umass0 at uhub0 port 1 configuration 1 interface 0
umass0: ADS Technologies lnc. USB2.0 Storage Device, rev 2.00/0.01, addr 2
umass0: using SCSI over Bulk-Only