Hi,

I'm trying to mount my fujifilm finepix camera under NetBSD.  It's
recognized by the umass driver.  Can anyone tell me how this is done?
I'm not entirely sure it's possible since I get an error at boot saying:

probe(umass0:0:0): generic HBA error

I've included the dmesg below.

Thanks!
-Nathan

------------dmesg-----------
NetBSD 1.6 (GENERIC_LAPTOP) #0: Sun Sep  8 19:55:58 UTC 2002

autobuild@tgm.daemon.org:/autobuild/i386/OBJ/autobuild/src/sys/arch/i386/compile/GENERIC_LAPTOP
cpu0: Intel Pentium III (Coppermine) (686-class), 498.81 MHz
cpu0: I-cache 16 KB 32b/line 4-way, D-cache 16 KB 32b/line 2-way
cpu0: L2 cache 256 KB 32b/line 8-way
cpu0: features 383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR>
cpu0: features 383f9ff<PGE,MCA,CMOV,FGPAT,PSE36,MMX>
cpu0: features 383f9ff<FXSR,SSE>
total memory = 255 MB
avail memory = 232 MB
using 3296 buffers containing 13184 KB of memory
BIOS32 rev. 0 found at 0xfd820
PCI BIOS rev. 2.1 found at 0xfd94f
pcibios: config mechanism [1][x], special cycles [x][x], last bus 7
PCI IRQ Routing Table rev. 1.0 found at 0xfdee0, size 208 bytes (11
entries)
PCI Interrupt Router at 000:07:0 (Intel 82371FB PCI-to-ISA Bridge (PIIX))
------------------------------------------
  device vendor product pin PIRQ IRQ stage
------------------------------------------
000:02:0 0x104c 0xac1b   A  0x00  11  0    already assigned
000:02:1 0x104c 0xac1b   B  0x01  10  0    already assigned
000:03:0 0x8086 0x1229   A  0x02   9  0    already assigned
000:03:1 0x115d 0x000c   A  0x02   9  0    already assigned
000:05:0 0x1013 0x6003   A  0x00  11  0    already assigned
000:07:2 0x8086 0x7112   D  0x03   9  0    already assigned
001:00:0 0x1002 0x4c4d   A  0x00  11  0    already assigned
------------------------------------------
PCI fixup examining 8086:7190
PCI fixup examining 8086:7191
PCI fixup examining 1002:4c4d
PCI bridge 0: primary 0, secondary 1, subordinate 1
PCI fixup examining 104c:ac1b
PCI bridge 1: primary 0, secondary 2, subordinate 2
PCI fixup examining 104c:ac1b
PCI bridge 2: primary 0, secondary 3, subordinate 3
PCI fixup examining 8086:1229
PCI fixup examining 115d:0c
PCI fixup examining 1013:6003
PCI fixup examining 8086:7110
PCI fixup examining 8086:7111
PCI fixup examining 8086:7112
PCI fixup examining 8086:7113
PCI bus #3 is the last bus
[System BIOS Setting]-----------------------
  device vendor product
  register space address    size
--------------------------------------------
000:00:0 0x8086 0x7190
	10h mem  0xf8000000 0x04000000
		[OK]
000:01:0 0x8086 0x7191
		[OK]
000:02:0 0x104c 0xac1b
	10h mem  0x50000000 0x00001000
		[OK]
000:02:1 0x104c 0xac1b
	10h mem  0x50100000 0x00001000
		[OK]
000:03:0 0x8086 0x1229
	10h mem  0xf4120000 0x00001000
	14h port 0x00001800 0x00000040
	18h mem  0xf4100000 0x00020000
		[OK]
000:03:1 0x115d 0x000c
	10h port 0x00001840 0x00000008
	14h mem  0xf4121000 0x00001000
		[OK]
000:05:0 0x1013 0x6003
	10h mem  0xf4122000 0x00001000
	14h mem  0xf4000000 0x00100000
		[OK]
000:07:0 0x8086 0x7110
		[OK]
000:07:1 0x8086 0x7111
	20h port 0x00001850 0x00000010
		[OK]
000:07:2 0x8086 0x7112
	20h port 0x00001860 0x00000020
		[OK]
000:07:3 0x8086 0x7113
		[OK]
001:00:0 0x1002 0x4c4d
	10h mem  0xf5000000 0x01000000
	14h port 0x00002000 0x00000100
	18h mem  0xf4200000 0x00001000
		[OK]
--------------------------[  0 devices bogus]
 Physical memory end: 0x0ffee000
 PCI memory mapped I/O space start: 0x10000000
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82443BX Host Bridge/Controller (rev. 0x03)
agp0 at pchb0: aperture at 0xf8000000, size 0x4000000
ppb0 at pci0 dev 1 function 0: Intel 82443BX AGP Interface (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: ATI Technologies Rage Mobility (rev. 0x64)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
cbb0 at pci0 dev 2 function 0: Texas Instruments PCI1450 PCI-CardBus
Bridge (rev. 0x03)
cbb1 at pci0 dev 2 function 1: Texas Instruments PCI1450 PCI-CardBus
Bridge (rev. 0x03)
fxp0 at pci0 dev 3 function 0: i82559S Ethernet, rev 9
fxp0: interrupting at irq 9
fxp0: Ethernet address 00:02:b3:04:58:2c
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Xircom WinGlobal Modem (serial communications, interface 0x02) at pci0 dev
3 function 1 not configured
clcs0 at pci0 dev 5 function 0: Cirrus Logic CS4280 CrystalClear Audio
Interface (rev. 0x01)
clcs0: interrupting at irq 11
clcs0: CRY20 codec; headphone, 20 bit DAC, 18 bit ADC, Crystal Semi 3D
audio0 at clcs0: full duplex, independent
midi0 at clcs0: CS4280 MIDI UART
pcib0 at pci0 dev 7 function 0
pcib0: Intel 82371AB PCI-to-ISA Bridge (PIIX4) (rev. 0x02)
pciide0 at pci0 dev 7 function 1: Intel 82371AB IDE controller (PIIX4)
(rev. 0x01)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
wd0 at pciide0 channel 0 drive 0: <IC25N010ATDA04-0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 9590 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 19640880
sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA
data transfers)
pciide0: secondary channel wired to compatibility mode
atapibus0 at pciide0 channel 1: 2 targets
cd0 at atapibus0 drive 0: <CD-224E, , 2.7B> type 5 cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
pciide0: secondary channel interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA
data transfers)
uhci0 at pci0 dev 7 function 2: Intel 82371AB USB Host Controller (PIIX4)
(rev. 0x01)
uhci0: interrupting at irq 9
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Intel 82371AB Power Management Controller (PIIX4) (miscellaneous bridge,
revision 0x03) at pci0 dev 7 function 3 not configured
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2 device 0
pcmcia0 at cardslot0
cbb1: interrupting at irq 10
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 3 device 0
pcmcia1 at cardslot1
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
lpt2 at isa0 port 0x3bc-0x3bf irq : polled
pcppi0 at isa0 port 0x61
midi1 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
apm0 at mainbus0: Power Management spec V1.2
biomask effd netmask effd ttymask ffff
umass0 at uhub0 port 1 configuration 1 interface 0
umass0: Fuji Photo Film USB Mass Storage, rev 1.10/10.00, addr 2
umass0: using ATAPI over CBI
atapibus1 at umass0 channel 0: 2 targets
probe(umass0:0:0): generic HBA error
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)