ok, I have run 1.52 for sometime with great success
but the newest version is give me this error 2 times
now, I fear more will come. and it requires a reboot.

Not good.

here is the error message

uvm_fault(0xc6cb7df4, 0x0, 0, 1) -> e
kernel: page fault trap, code=0
stopped in pid 232 (bash) at uvmfault_anonget+0x61:
cmpw $0, 0x2a(%ebx)


here is my dmesg, as you guys always ask for.


NetBSD 1.6 (GENERIC) #0: Sun Sep  8 19:43:40 UTC 2002
   
autobuild@tgm.daemon.org:/autobuild/i386/OBJ/autobuild/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium/MMX (586-class), 166.41 MHz
cpu0: features 8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
cpu0: features 8001bf<MMX>
total memory = 65148 KB
avail memory = 53956 KB
using 839 buffers containing 3356 KB of memory
RTC BIOS diagnostic error 2
BIOS32 rev. 0 found at 0xf1b00
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line,
rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: VIA Technologies VT82C595 (Apollo VP2) Host-PCI
Bridge (rev. 0x03)
pcib0 at pci0 dev 7 function 0
pcib0: VIA Technologies VT82C586 (Apollo VP) PCI-ISA
Bridge (rev. 0x31)
pciide0 at pci0 dev 7 function 1: VIA Technologies
VT82C586 (Apollo VP) ATA33 controller
pciide0: bus-master DMA support present
pciide0: primary channel configured to compatibility
mode
wd0 at pciide0 channel 0 drive 0: <ST34342A>
wd0: drive supports 16-sector PIO transfers, LBA
addressing
wd0: 4103 MB, 8894 cyl, 15 head, 63 sec, 512
bytes/sect x 8404830 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA
mode 2 (Ultra/33)
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
(Ultra/33) (using DMA data transfers)
pciide0: secondary channel configured to compatibility
mode
pciide0: disabling secondary channel (no drives)
uhci0 at pci0 dev 7 function 2: VIA Technologies
VT83C572 USB Controller (rev. 0x02)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA Technologie UHCI root hub, class 9/0, rev
1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
VIA Technologies VT82C586 (Apollo VP) Power Management
Controller (miscellaneous prehistoric) at pci0 dev 7
function 3 not 

configured
vga1 at pci0 dev 15 function 0: S3 Trio64V2/DX (rev.
0x14)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100
emulation)
wsmux1: connecting to wsdisplay0
isa0 at pcib0
ep0 at isa0 port 0x300-0x30f irq 10: 3Com 3C509
Ethernet
ep0: address 00:60:08:07:da:10, 8KB byte-wide FIFO,
1:1 Rx:Tx split
ep0: 10baseT (default 10baseT)
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working
fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device
support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
biomask fb6d netmask ff6d ttymask ffef
Kernelized RAIDframe activated
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
IP Filter: v3.4.27 initialized.  Default = pass all,
Logging = enabled
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)



__________________________________________________
Do you Yahoo!?
Yahoo! Tax Center - File online, calculators, forms, and more
http://tax.yahoo.com