Hi,

Thanks to a different network and some help from a couple folks, I was
able to get this laptop installed.  Still, it hangs when I insert the
wireless card.

The full dmesg, without the wireless card, is attached below.  The
card in question is a very standard WaveLAN 11MB Gold, which the other
BSDs seem to pick right up.

I'm running on the GENERIC_LAPTOP kernel.  (I installed using the
GENERIC kernel, then built and installed the GENERIC_LAPTOP kernel.)

Any suggestions?

Thanks,
==ml


etBSD 1.6 (GENERIC_LAPTOP) #0: Thu Jan  2 07:49:54 EST 2003
    root@crashbox.blackhelicopters.org:/usr/src/sys/arch/i386/compile/GENERIC_LAPTOP
cpu0: Intel Pentium III (Coppermine) Celeron (686-class), 646.85 MHz
cpu0: I-cache 16 KB 32b/line 4-way, D-cache 16 KB 32b/line 2-way
cpu0: L2 cache 128 KB 32b/line 4-way
cpu0: features 383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR>
cpu0: features 383f9ff<PGE,MCA,CMOV,FGPAT,PSE36,MMX>
cpu0: features 383f9ff<FXSR,SSE>
total memory = 319 MB
avail memory = 291 MB
using 4115 buffers containing 16460 KB of memory
BIOS32 rev. 0 found at 0xfe0db
PCI BIOS rev. 2.1 found at 0xff85c
pcibios: config mechanism [1][x], special cycles [x][x], last bus 21
PCI IRQ Routing Table rev. 1.0 found at 0xf0460, size 128 bytes (6 entries)
PCI Interrupt Router at 000:05:0 (Intel 82371FB PCI-to-ISA Bridge (PIIX))
------------------------------------------
  device vendor product pin PIRQ IRQ stage
------------------------------------------
000:05:2 0x8086 0x7112   D  0x03  11  0    already assigned
000:08:0 0x8086 0x1229   A  0x02  11  0    already assigned
000:08:1 0x115d 0x00d4   A  0x02  11  0    already assigned
000:11:0 0x1179 0x0617   A  0x00  11  0    fixed up
000:11:1 0x1179 0x0617   B  0x01  11  0    fixed up
000:12:0 0x1073 0x0012   A  0x01  11  0    already assigned
001:00:0 0x5333 0x8c12   A  0x00  11  0    already assigned
------------------------------------------
PCI fixup examining 8086:7190
PCI fixup examining 8086:7191
PCI fixup examining 5333:8c12
PCI bridge 0: primary 0, secondary 1, subordinate 1
PCI fixup examining 8086:7110
PCI fixup examining 8086:7111
PCI fixup examining 8086:7112
PCI fixup examining 8086:7113
PCI fixup examining 8086:1229
PCI fixup examining 115d:d4
PCI fixup examining 1179:617
PCI bridge 1: primary 0, secondary 2, subordinate 2
PCI fixup examining 1179:617
PCI bridge 2: primary 0, secondary 3, subordinate 3
PCI fixup examining 1073:12
PCI bus #3 is the last bus
[System BIOS Setting]-----------------------
  device vendor product
  register space address    size
--------------------------------------------
000:00:0 0x8086 0x7190 
	10h mem  0xd0000000 0x10000000
		[OK]
000:01:0 0x8086 0x7191 
		[OK]
000:05:0 0x8086 0x7110 
		[OK]
000:05:1 0x8086 0x7111 
	20h port 0x0000fff0 0x00000010
		[OK]
000:05:2 0x8086 0x7112 
	20h port 0x0000ff80 0x00000020
		[OK]
000:05:3 0x8086 0x7113 
		[OK]
000:08:0 0x8086 0x1229 
	10h mem  0xeffff000 0x00001000
	14h port 0x0000ff40 0x00000040
	18h mem  0xeffc0000 0x00020000
		[OK]
000:08:1 0x115d 0x00d4 
	10h port 0x0000ff38 0x00000008
	14h mem  0xefdff000 0x00001000
		[OK]
000:11:0 0x1179 0x0617 
	10h mem  0x00000000 0x00001000
		[NG]
000:11:1 0x1179 0x0617 
	10h mem  0x00000000 0x00001000
		[NG]
000:12:0 0x1073 0x0012 
	10h mem  0xefdf0000 0x00008000
	14h port 0x0000fec0 0x00000040
	18h port 0x0000febc 0x00000004
		[OK]
001:00:0 0x5333 0x8c12 
	10h mem  0xf0000000 0x08000000
		[OK]
--------------------------[  2 devices bogus]
 Physical memory end: 0x13fde000
 PCI memory mapped I/O space start: 0x14000000
[PCIBIOS fixup stage]-----------------------
  device vendor product
  register space address    size
--------------------------------------------
000:00:0 0x8086 0x7190 
	10h mem  0xd0000000 0x10000000
		[OK]
000:01:0 0x8086 0x7191 
		[OK]
000:05:0 0x8086 0x7110 
		[OK]
000:05:1 0x8086 0x7111 
	20h port 0x0000fff0 0x00000010
		[OK]
000:05:2 0x8086 0x7112 
	20h port 0x0000ff80 0x00000020
		[OK]
000:05:3 0x8086 0x7113 
		[OK]
000:08:0 0x8086 0x1229 
	10h mem  0xeffff000 0x00001000
	14h port 0x0000ff40 0x00000040
	18h mem  0xeffc0000 0x00020000
		[OK]
000:08:1 0x115d 0x00d4 
	10h port 0x0000ff38 0x00000008
	14h mem  0xefdff000 0x00001000
		[OK]
000:11:0 0x1179 0x0617 
	10h mem  0x14000000 0x00001000
		[OK]
000:11:1 0x1179 0x0617 
	10h mem  0x14001000 0x00001000
		[OK]
000:12:0 0x1073 0x0012 
	10h mem  0xefdf0000 0x00008000
	14h port 0x0000fec0 0x00000040
	18h port 0x0000febc 0x00000004
		[OK]
001:00:0 0x5333 0x8c12 
	10h mem  0xf0000000 0x08000000
		[OK]
--------------------------[  0 devices bogus]
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82443BX Host Bridge/Controller (rev. 0x03)
agp0 at pchb0: aperture at 0xd0000000, size 0x8000000
ppb0 at pci0 dev 1 function 0: Intel 82443BX AGP Interface (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: S3 Savage/IX+MV (rev. 0x11)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
pcib0 at pci0 dev 5 function 0
pcib0: Intel 82371AB PCI-to-ISA Bridge (PIIX4) (rev. 0x02)
pciide0 at pci0 dev 5 function 1: Intel 82371AB IDE controller (PIIX4) (rev. 0x01)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
wd0 at pciide0 channel 0 drive 0: <TOSHIBA MK4018GAP>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 38154 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 78140160 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
pciide0: secondary channel wired to compatibility mode
atapibus0 at pciide0 channel 1: 2 targets
cd0 at atapibus0 drive 0: <TOSHIBA DVD-ROM SD-C2402, Z000500169, 1317> type 5 cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
pciide0: secondary channel interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
uhci0 at pci0 dev 5 function 2: Intel 82371AB USB Host Controller (PIIX4) (rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Intel 82371AB Power Management Controller (PIIX4) (miscellaneous bridge, revision 0x03) at pci0 dev 5 function 3 not configured
fxp0 at pci0 dev 8 function 0: i82559S Ethernet, rev 9
fxp0: interrupting at irq 11
fxp0: Ethernet address 00:10:a4:10:28:ae
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Xircom product 0x00d4 (serial communications, interface 0x02) at pci0 dev 8 function 1 not configured
cbb0 at pci0 dev 11 function 0: Toshiba ToPIC100 CardBus-PCI Bridge (rev. 0x20)
cbb1 at pci0 dev 11 function 1: Toshiba ToPIC100 CardBus-PCI Bridge (rev. 0x20)
yds0 at pci0 dev 12 function 0: Yamaha 754 (DS-1E) Audio (rev. 0x00)
yds0: interrupting at irq 11
yds0: Asahi Kasei AK4543 codec; headphone, 18 bit DAC, 18 bit ADC, AKM 3D
audio0 at yds0: full duplex, mmap, independent
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2 device 0
pcmcia0 at cardslot0
cbb1: interrupting at irq 11
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 3 device 0
pcmcia1 at cardslot1
opl0 at yds0: model OPL3
midi1 at opl0: DS-1 integrated Yamaha OPL3
mpu0 at yds0
midi2 at mpu0: Yamaha DS-1 MIDI UART
apm0 at mainbus0: Power Management spec V1.2
biomask ef7d netmask ef7d ttymask ffff
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)



-- 
Michael Lucas		mwlucas@FreeBSD.org, mwlucas@BlackHelicopters.org
http://www.oreillynet.com/pub/q/Big_Scary_Daemons

           Absolute BSD:   http://www.AbsoluteBSD.com/