>Date: Fri, 10 Dec 1999 18:19:18 +0100
>To: port-i386
>From: Richard PLOIX <richard.ploix@gsi.fr>
>Subject: I don'see where is my CDROM for mounting it?
>
>Hello,
>my config is : DELL Pentium 200 Pro, 1 SCSI disk 2.5 Go target 0, 1 SCSI
disk 8.4 Go target 1, 1 SCSI CDROM target 5.
>I don't see who is the CDROM.
>I've trying /dev/cd0a, /dev/cd0d, /dev/cd1a, /dev/cd1d, /dev/sd0a,
/dev/sd0d, /dev/sd1a, /dev/sd1d, /dev/sd5a, /dev/sd5d.
>nothing was good for mounting my CDROM by the command line : mount -rt
cd9660 /dev/sdxx /mnt/cdrom.
>the directory /mnt/cdrom exists.
>I've trying the same thing in the fstab file: /dev/xxxx /mnt/cdrom cd9660
ro,noauto 0 0.
>Here is my dmesg.log file:
>-------------------------->
>NetBSD 1.4.1 (GENERIC) #1: Tue Aug 10 00:03:09 MEST 1999
>
fvdl@struis:/usr/src/sys/arch/i386/compile/GENERIC
>cpu0: family 6 model 1
step 9
>cpu0: Intel Pentium Pro (686-class)
>real mem  = 66715648
>avail
mem = 58339328
>using 840 buffers containing 3440640 bytes of
memory
>mainbus0 (root)
>pci0 at mainbus0 bus 0: configuration mode
1
>pci0: i/o enabled, memory enabled
>pchb0 at pci0 dev 0 function
0
>pchb0: Intel 82441FX PCI and Memory Controller (PMC) (rev. 0x02)
>pcib0
at pci0 dev 13 function 0
>pcib0: Intel 82371SB PCI-to-ISA Bridge (PIIX3)
(rev. 0x01)
>pciide0 at pci0 dev 13 function 1: Intel 82371SB IDE Interface
(PIIX3)
>pciide0: bus-master DMA support present
>pciide0: primary channel
wired to compatibility mode
>pciide0: disabling primary channel (no
drives)
>pciide0: secondary channel wired to compatibility mode
>pciide0:
secondary channel ignored (disabled)
>ppb0 at pci0 dev 14 function 0:
Digital Equipment DECchip 21052 PCI-PCI Bridge (rev. 0x01)
>pci1 at ppb0
bus 1
>pci1: i/o enabled, memory enabled
>ex0 at pci1 dev 8 function 0:
3Com 3c905-TX 10/100 Ethernet
>ex0: interrupting at irq 11
>ex0: MAC
address 00:c0:4f:b6:5b:e0
>nsphy0 at ex0 phy 24: DP83840 10/100 media
interface, rev. 1
>nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
>ahc1 at pci1 dev 11 function 0
>ahc1: interrupting at irq 10
>ahc1:
aic7880 Wide Channel, SCSI Id=7, 16 SCBs
>scsibus0 at ahc1 channel 0: 16
targets, 8 luns per target
>ahc1: target 0 synchronous at 10.0MHz, offset =
0xf
>sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST32550N, 0019> SCSI2 0/direct
fixed
>sd0: 2047MB, 3511 cyl, 11 head, 108 sec, 512 bytes/sect x 4194058
sectors
>ahc1: target 1 synchronous at 10.0MHz, offset = 0xf
>sd1 at
scsibus0 targ 1 lun 0: <QUANTUM, FIREBALL SE8.4S, PJ0A> SCSI2 0/direct
fixed
>sd1: 8191MB, 7637 cyl, 8 head, 274 sec, 512 bytes/sect x 16777215
sectors
>ahc1: board is not responding
>cmd fail
>probe(ahc1:5:0): timed
out in datain phase, SCSISIGI == 0x44
>probe(ahc1:5:0): asserted ATN -
device reset in message buffer
>ahc1: board is not responding
>cmd
fail
>sd2 at scsibus0 targ 5 lun 0: <, , > SCSI0 0/direct fixed
>ahc1:
board is not responding
>ahc1: board is not responding
>sd2: mode sense (4)
returned nonsense; using fictitious geometry
>ahc1: board is not
responding
>cmd fail
>sd2: 40960MB, 40960 cyl, 64 head, 32 sec, 512
bytes/sect x 83886081 sectors
>vga1 at pci0 dev 16 function 0: S3 Trio32/64
(rev. 0x54)
>wsdisplay0 at vga1: console (80x25, vt100 emulation)
>isa0 at
pcib0
>com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
>com1 at
isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
>lpt0 at isa0 port
0x378-0x37b irq 7
>sb0 at isa0 port 0x220-0x237 irq 5 drq 1 drq2 5: dsp
v4.13
>audio0 at sb0: full duplex
>opl0 at sb0: model OPL3
>midi0 at opl0:
<SB Yamaha OPL3>
>pckbc0 at isa0 port 0x60-0x64
>pckbd0 at pckbc0 (kbd
slot)
>pckbc0: using irq 1 for kbd slot
>wskbd0 at pckbd0: console
keyboard
>opms0 at pckbc0 (aux slot)
>pckbc0: using irq 12 for aux
slot
>pcppi0 at isa0 port 0x61
>midi1 at pcppi0: <PC speaker>
>sysbeep0 at
pcppi0
>isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
>npx0
at isa0 port 0xf0-0xff: using exception 16
>fdc0 at isa0 port 0x3f0-0x3f7
irq 6 drq 2
>fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
>isapnp0:
no ISA Plug 'n Play devices found
>biomask 440 netmask c40 ttymask
1cc2
>wscons: wskbd0 glued to wsdisplay0 (console)
>sd0: no disk
label
>sd2(ahc1:5:0): timed out in dataout phase, SCSISIGI == 0x0
>ahc1:
Issued Channel A Bus Reset #1. 6 SCBs aborted
>findroot: can't open dev
sd2a (5)
>ahc1: target 0 synchronous at 10.0MHz, offset = 0xf
>ahc1: target
1 synchronous at 10.0MHz, offset = 0xf
>ahc1: target 5 synchronous at
10.0MHz, offset = 0xf
>boot device: sd1
>root on sd1a dumps on sd1b
>root
file system type: ffs
>wsdisplay0: screen 4 added (80x25, vt100
emulation)
>----------------------->
>